基于激波风洞的超声速磁流体动力技术实验系统

开展磁流体(MHD)动力技术实验研究,实验系统必须满足两项基本的条件:一是超声速或高超声速气流;二是气流必须是导电流体.基于此,介绍了基于激波风洞的超声速磁流体动力技术实验系统的基本组成、设计思想和调试情况.设计了马赫数Ma=2的超声速喷管及实验段;采用氦气驱动氩气,在平衡接触面运行方式下得到高温气体,通过在低压段注入...     

SiO_2-C复合气凝胶的制备及其结构

以间苯二酚(R)和甲醛(F)为碳源,以3-胺丙基三乙氧基硅烷(APTES)为硅源,一步溶胶一凝胶法简单快捷地合成了SiO_2-RF复合气凝胶,高温碳化后得到SiO_2-C复合气凝胶,并用扫描电镜、比表面分析仪对所得样品的结构进行了研究,并讨论了不同投料比对气凝胶结构的影响.结果表明碳化前,投料比APTES/R=1时,所得气凝胶具有最大的比表面积(S_(BET)=606.1 m~2/g),碳化后,由于体积收缩和酚醛热解产生新孔隙双重因素的影响,投料比AFTES/R=1/2时样品的比表面积达到最大(S_(BET)=704.2 m~2/g).     

Al－Al_3Ni自生复合材料的高周疲劳损伤断裂机制及其应力比的影响

实验观察和研究了Ａｌ－Ａｌ３Ｎｉ自生复合材料的高周疲劳损伤断裂行为以及应力比Ｒ的影响,结果显示在Ｒ＝－１疲劳过程中孔洞沿界面区基体的优先萌生、联接和扩展是其损伤断裂的主要机制;并且发现Ｒ对疲劳寿命及断裂过程有明显影响,当Ｒ＝０时滑移带裂纹生长相对容易,寿命减小,而Ｒ＝∞时,裂纹集中在类似于压缩变形的宏观形变带内发展,寿命很长     

Detection Performance of Logarithmic Receivers Employing Video Integrators

The detection performance of logarithmic receivers in Rayleigh and non-Gaussian clutter is investigated. In Rayleigh clutter the performance is determined for steady, Swerling case 1, and Swerling case 2 targets. The detection loss of logarithmic receivers is generally less than the ? log n loss conjectured by Green, but consistent with the 1.08-dB asymptotic loss established by Hansen. The Swerling case 2 loss, important in frequency- agility applications, canbe severe for a small number of integrated pulses and high Pd, and apparently approaches the 1.08-dB asymptotic loss as a lower bound. Graphs of GramCharlier series cumulants are provided to allow determination of logarithmic-receiver performance. Curves are presented to allow the detection performance of logarithmic receivers in log-normal and Weibull clutter to be determineds.     

Polar format algorithm for bistatic SAR

Matched filtering (MF) of phase history data is a mathematically ideal but computationally expensive approach to bistatic synthetic aperture radar (SAR) image formation. Fast backprojection algorithms (BPAs) for image formation have recently been shown to give improved O(N/sup 2/ log/sub 2/N) performance. An O(N/sup 2/ log/sub 2/N) bistatic polar format algorithm (PFA) based on a bistatic far-field assumption is derived. This algorithm is a generalization of the popular PFA for monostatic SAR image formation and is highly amenable to implementation with existing monostatic image formation processors. Limits on the size of an imaged scene, analogous to those in monostatic systems, are derived for the bistatic PFA.     

Phase-Lock Loop Jump Phenomenon in the Presence of Two Signals

Jump phenomena are known to exist in many non-linear systems [I], [2], [3]. The non-linear analysis presented in this paper explains and predicts the conditions for the jump phenomenon that is observed in a phase-locked loop (PLL) preceded by an automatic gain control (AGC). The jump phenomenon occurs when the frequency separation AM of two sinusoids at the input to the AGC is greater than the bandwidth B of the linearized PLL. If the loop is initially locked to the stronger signal, the weaker signal will frequency-modulate the PLL voltage-controlled oscillator (VCO) with a modulation frequency AI. The amplitude S2 of the weaker signal al can be increased until it becomes greater than the amplitude Si of the signal being tracked, without causing the loop to lose lock; i. e., the VCO continues to track the original signal. However, if the ratio of the amplitudes S2 S1 = R is increased above some critical value RC > 1, the loop will lose lock on the original signal, and jump to track the interfering signal. If the frequency separation is at least twice the PLL bandwidth, a good approximation for this critical ratio is Rc ? ?w/B.     

False alarm analysis of the envelope detection GO-CFAR processor

The greatest of constant false alarm rate processor (GO CFAR) is a useful architecture for adaptively setting a radar detection threshold in the presence of clutter edges. The GO CFAR input is often the envelope detected in-phase (I) and quadrature (Q) channels of the baseband signal (x_e=√(I²+Q²)). This envelope detection can also be approximated using x=a max{|I|,|Q|}+b min{|I|,|Q|} which requires less complex hardware (a and b are simple multiplying coefficients). The envelope GO CFAR processor and several envelope approximation GO CFAR processors are compared in terms of the probability of false alarm (PFA) performance. Closed-form expressions which describe the PFA performance are given and their accuracy evaluated. It is shown that for all cases, the PFA is proportional to the number of reference cells n for small threshold multiplier T and inversely proportional to n for large T. A region of intersection occurs where the PFA is the same for two different values of n. For example, at T'=1.68 in the |I|+|Q| GO CFAR (a=1, b=1) the PFA for n=1 is equal to the optimal n=∞ fixed-threshold PFA (PFA=0.112)     

Thermal Noise Errors in DF Monopulse Systems Having Log Amplifiers

An analysis of the effects of thermal noise on the accuracy of direction finding (DF) monopulse systems which employ logarithmic amplifiers is presented. Numerical results are presented which indicate that a simple model may be used to compute rms thermal errors for a wide range of signal levels. Analytical results obtained in the limit of large signal-to-noise ratios are compared with standard results used to analyze monopulse systems employing automatic gain control (AGC) circuitry instead of log amplifiers.     

Wind asymmetries in massive stars

We are in the process of surveying the linear polarization in luminous, early-type stars. We here report on new observations of the B [e] stars S 18 and R 50, and of the Luminous Blue Variables HR Car, R 143, and HD 160529. Together with previously published data, these observations provide clear evidence for the presence of intrinsic polarization in 1 B[e] star (HD 34664) and in 5 LBVs ( Car, P Cyg, R 127, AG Car, and HR Car). The data indicate that anisotropic stellar winds are a common occurrence among massive stars in these particular evolutionary stages. For such stars, mass-loss rates estimated using the assumption of a spherical, homogeneous and stationary outflow may be in error.     

TiBw/TA15复合材料板材超塑变形行为研究

研究了TiB_w/TA15复合材料板材在900~960℃、5×10^-4~10^-2s^-1条件下的超塑变形行为。结果表明,TiB_w/TA15复合材料流变应力随拉伸温度的升高和应变速率的减小而降低,在940℃、5×10^-3s^-1变形条件下获得的最大超塑性伸长率为439%。利用Zener-Hollomn参数和Arrhenius方程所建立的峰值应力本构方程为ε·=3.55×10⁸[sinh(2.0×10^-2σ)]^1.99×exp(-6.381×10⁵/RT),其变形激活能Q=638.1kJ/mol。复合材料超塑性变形组织与拉伸温度和应变速率密切相关。高温低应变速率有利于基体α相的动态再结晶以及晶须与基体处孔洞的愈合,低温高应变速率下,孔洞更易萌生于增强相与基体结合界面的端部。动态再结晶对复合材料超塑性的发挥起着关键作用。     

STATIC AND FATIGUE BEHAVIOR OF IMPACTED AS4/PEEK THERMOPLASTIC COMPOSITES UNDER COMPRESSION LOAD

Static and fatigue tests under compression load were made on impacted AS4/PEEK and T300/913C graphite/epoxy with ［45/90/-45/0］_5S stacking sequence. The comparison of the damage tolerance assessment for thermosetting and thermoplastic composites shows that thermoplastics are more damage tolerant under compression. Impacted thermoplastic composites have excellent compression-compression fatigue behavior. The damage growth life is only a few percent of their total fatigue life and no regular damage growth can be found. Some design principles for thermosetting composite structures may still be used.     

可压缩流体恒温热线风速仪校准方法

开展了恒温(CT)热线风速仪校准方法的研究,以满足可压缩流体中湍流度测量需求。将对数函数与多元回归技术相结合,建立了恒温热线风速仪校准的数学模型,并进行了风洞湍流度测量试验验证。在马赫数Ma=0.3~0.55范围内进行了校准试验,根据建立的数学模型对试验数据进行拟合,拟合优度R2=0.999 82,平均绝对速度偏差Δu=0.18m/s,基本满足了恒温热线风速仪校准精度要求。对马赫数Ma=0.55条件下流场进行了湍流度测量,速度测量偏差为0.034%,流场湍流度Tu=0.14%。试验结果证明了恒温热线风速仪应用于可压缩流体速度测量的可行性。     

15%SiC_P/8009铝基复合材料热压缩流变应力行为

采用Gleeble-3500热模拟试验机对15%Si CP/8009铝基复合材料在温度为400~550℃和应变速率为0.001~1 s~(-1)条件下的热变形流变行为进行研究。结果表明:流变应力在开始阶段随应变的增加而增大,出现峰值后逐渐趋于平稳;流变应力随温度的升高而降低,随应变速率的增大而升高,呈现出正应变速率敏感性;流变应力行为可以用双曲正弦模型来描述,其热变形激活能为488.3853 k J/mol,应力指数为7.19022。     

定向凝固Ni-44Ti-5Al-2Nb-1Mo合金的组织特征

采用液态金属冷却定向凝固方法制备了Ni-44Ti-5 Al-2 Nb-1 Mo(原子分数,％)合金,分析了加热温度为1 550℃,抽拉速率为0.3、1.2、3.0、6.0、18.0 mm/min时的定向凝固组织特征.结果表明,定向凝固没有改变合金的相组成,但改变了组成相的形态.定向凝固组织均由初生的NiTi相与晶间析出...     

A Logarithmic Frequency Allocation Algorithm for Wideband Discrete Frequency Pulse Trains

It is shown that signal waveforms utilizing discrete frequency modulation (DFM) which are generated using a narrowband or frequency shift algorithm have ambiguity sidelobe distortion which is caused by the approximation of time compression by frequency shift. A logarithmic frequency allocation algorithm is presented which couches the signal design problem in terms of band and step ratios, rather than in terms of bandwidth and frequency steps, and is consistent with the wideband formulation of the ambiguity function. The algorithm makes use of the same basic code generating sequence used for narrowband frequency allocation, but the resulting signal will have invariant ambiguity sidelobe positions for any receiver realization in the delay-time compression plane.     

自适应滤波方法研究

证明Ｓａｇｅ－Ｈｕｓａ的自适应卡尔曼滤波算法不能同时估计Ｑ和Ｒ,并分析了该法导致滤波发散的原因。介绍了一种新的自适应卡尔曼滤波算法,该法当Ｒ（或Ｑ）已知时可以准确地估计出Ｑ（或Ｒ）。该法的独特之处在于当对Ｑ（或Ｒ）进行修正估计时,只采用矩阵的乘运算和求逆运算,而不进行加减法运算,因此消除了滤波发散现象。数字仿真表明效果良好。     

A new analysis model for the effective stiffness of stiffened metallic panels under combined compression and shear stress

The paper deals with the analysis of the effective stiffness of stiffened metallic panels under combined compression and shear stress as used, e.g. in aircraft fuselages. An important criterion for sizing and certification of aircraft fuselages is the local and global buckling behaviour. For optimisation of stiffened metallic panels it is necessary to know the buckling and postbuckling behaviour as accurately as possible. Due to the fact that nonlinear FE analyses of a whole aircraft fuselage are too time consuming, a very fast quasi nonlinear FE analysis with a coarse mesh under consideration of semi-empirical methods for the effective skin-stiffness are used. At this point the effective stiffness method derived in this paper is used. Admittedly previous semi-empirical methods like the effective width method [J. Wiedemann, Leichtbau 1: Elemente, second ed., 1996; M.C.Y. Niu, Airframe Stress Analysis and Sizing, second ed., Commilit. Press Ltd., 1999] (only for pure compression load) or the method of Kuhn [P. Kuhn, J.P. Peterson, L.R. Levin, A summary of diagonal tension part I – methods of analysis, Technical Note 2661, NACA, 1952] (only for pure shear load) have disadvantages for the general combined compression and shear load case. This is improved in the current method.The first part of the paper deals with the realisation of the compression and shear test facility in a finite element model. The verification of the finite element model is important for subsequent parameter variations. The second part of the paper presents the approach of how to assess the effective skin-stiffness. In comparison to the paper in [M. Heitmann, P. Horst, D. Fitzsimmons, Effective stiffness of postbuckled stiffened metallic panels under combined compression and shear stress, J. Strain Anal. 38 (6) (2003) 534–555] many new parameters have been analysed. Therefore the new approach for the geometrically nonlinear analysis derived from the finite element results for combined compression and shear stress is considerably improved. At the end of the paper the great benefit of the new approach is shown. The results of very fast quasi nonlinear FE analyses under consideration of the new approach for the effective skin-stiffness on a coarse panel mesh agree well with the results of time expensive nonlinear FE analysis on a very fine panel mesh. Further studies are necessary to expand the new method to the influence of plasticity.     

CLF-1钢X数字射线照相等效系数的确定

针对聚变堆结构材料拟采用的新材料CLF-1(low-activated ferritic/martensitic steel)钢在进行射线检测过程中没有特定标准参考的问题,采用等效法在相同透照条件开展了不同厚度CLF-1钢和Q235钢的X数字射线等效透照实验研究。基于相同成像条件下两种材料对应的X射线图像具有相同灰度即透照系数相同,通过对比拥有相同图像灰度值的两种材料的厚度,得出CLF-1钢对应于Q235钢的等效透照系数。试验设计了4~20 mm,递增0.5 mm的阶梯厚度的CLF-1钢和Q235钢在100~400 kV(递增50 kV)管电压条件下进行了透照实验,获得了对应电压下CLF-1钢相对于Q235钢的X射线透照等效系数为1.10~1.13。该研究结果对CLF-1钢在进行X射线检测时的检测技术参数的确定具有指导意义。     

液浮磁悬浮摆式加速度计数字伺服电路设计

液浮磁悬浮摆式加速度计的研制主要包括高性能铍材结构设计和工艺、磁悬浮稳定支承、高精度温控补偿及高精度伺服控制等关键技术,具有精度高、抗干扰能力强、体积小等特点,可应用于航海、航天、航空等多种领域的惯性系统,并直接决定着导航和制导系统的性能和精度。结合液浮磁悬浮摆式加速度计高精度伺服控制需求,本文主要介绍了一种基于18位A/D采集、具备浮点运算功能的TMS320F28335[1-5]、半桥式力矩驱动电路等硬件设计的数字伺服控制技术,为液浮磁悬浮摆式加速度计提供高精度伺服控制方案。     

流线追踪Busemann进气道设计参数的选择

为了研究型面设计马赫数、唇口偏移量对流线追踪Busemann进气道设计点性能的影响规律,寻求最佳性能的进气道,对设计马赫数为6,具有不同型面设计马赫数和唇口偏移量的流线追踪进气道进行了数值模拟。研究表明:选取低于马赫数6的型面设计马赫数,可获得较高的流量系数和增压比,而其压缩效率并不低;进气道唇口偏移量增大,会导致流量系数、增压比变小,但却有利于减小进气道内的分离程度,还会影响隔离段内的流动,因此唇口偏移量的选取需要综合考虑。