带肋回转变截面通道内换热特性的实验研究

用实验方法研究了某航空发动机涡轮叶片内部带肋变截面180°回转通道壁面的换热特性,分析了上下面带60°平行斜肋和带60°交叉肋两种分布形式对换热的影响。实验结果表明:通道的努赛尔数随着雷诺数的增加而增大。在低雷诺数下两者的通道平均换热效果是相近的;在高雷诺数下交叉肋通道平均换热效果好于平行斜肋通道。变截面通道的壁面温度分布没有严格的以肋间距为周期的变化规律;交叉肋通道壁面温度沿流体流向的梯度要比平行肋通道的小。     

Hot deformation behavior and microstructure evolution of the laser solid formed TC4 titanium alloy

Hot compressive experiments of the laser solid formed (LSFed) TC4 titanium alloy were conducted at a wide temperature range of 650–950 °C and strain rate of 0.01–10 s⁻¹. The Arrhenius-type constitutive models of the LSFed TC4 alloy were established at the temperature range of 800–950 °C and of 650–800 °C, respectively. The average relative error between the predicted stresses and experimental values in those two temperature ranges are 10.4% and 8.3%, respectively, indicating that the prediction models constructed in this paper are in a good agreement with experimental data. Processing maps were established by the principle of dynamic materials modeling on the basis of the data achieved from the hot compression experiments. The processing parameters corresponding to the stable and unstable regions of material deformation can be determined from the processing maps. The microstructure evolution of the stable and unstable regions of the samples after tests were observed. Finally, the effect of hot compressive parameters on the microstructure were investigated to research the dynamic recrystallization and the texture of the deformed LSFed TC4 alloy.     

单向C/C复合材料高温氧化环境力学性能试验

为研究高温氧化环境单向C/C复合材料力学特性,对C/C复合材料单向板开展了700℃和900℃的氧化试验以及室温、700℃和900℃的拉伸试验.结果 表明:无涂层单向C/C复合材料在相同温度下,失重率随着氧化时间的增加而增大,在相同氧化时间内,温度越高,氧化失重率越大;无涂层单向C/C复合材料在700℃氧化4h后失重率为...     

姿/ 轨控液体火箭发动机推力室高温抗氧化涂层

概述了国内外姿/轨控液体火箭发动机高温抗氧化涂层的研究和应用进展,研制过程涉及多种材料体系,但仅有几类广泛应用于型号,包括Nb基材表面硅化物材料体系、Pt-Rh合金、Re基材表面Ir涂层。随着对发动机性能要求的提高,Re/Ir材料体系成为目前主要的研究方向。     

Surface Recrystallization in Nickel Base Single Crystal Superalloy DD6

The samples of single crystal superalloy DD6 are grit blasted and then heat treated either with the standard heat treatment procedure or in the temperature range of 1 000-1 250 °C for 4-16 h at vacuum atmosphere, then the recrystallization behavior of DD6 alloy is investigated. The results show that the equiaxed recrystallization grains form in the γ phase region where the as-cast γ′ phases have been dissolved completely, and cellular recrystallization forms in the region where the as-cast γ′ phases have been dissolved partially. The cellular recrystallization area consists of cellular grains, and the cellular grain consists of cubic γ′ phase, lamellar γ′ phase and γ+γ′ The coexistence of the equiaxed recrystallization zones and cellular recrystallization zones is a recrystallized characteristic of the cold worked single crystal samples which are heat treated at a temperature lower than the solution temperature. When the heating temperature is higher than 1 150 °C, with the increase of heat treating temperature, the equiaxed recrystallization zone expands, whereas the cellular recrystallization zone shrinks. All the deformed regions are consumed by equiaxed recrystallization after annealing at solution temperature.     

HIP-Re 组织及力学性能

采用粉末冶金热等静压技术制备了HIP-Re纯铼材料,分析了不同热处理状态对材料微观结构及室温和高温性能的影响。结果表明,热处理温度对材料拉伸性能影响较大,经1 800℃/1.5 h真空处理HIP-Re抗拉强度达到1 196 MPa,伸长率为19.1%;2 000℃抗拉强度达到69 MPa,伸长率达17%以上。粉末冶金铼的晶粒组织多为2～8μm细小等轴晶,HIP-Re断裂方式为沿晶断裂与穿晶断裂共同作用,高温断裂方式为晶间断裂与滑移断裂,在拉伸形变过程中,Re材料内部产生了大量协变的裂纹及微孔,裂纹扩展连接导致断裂。     

High-temperature oxidation behavior and analysis of impedance spectroscopy of 7YSZ thermal barrier coating prepared by plasma spray-physical vapor deposition

Quasi-columnar structure 7YSZ(yttria stabilized zirconia) thermal barrier coatings(TBCs) are prepared by plasma spray-physical vapor deposition(PS-PVD) onto pretreated and un-pretreated bond coating, respectively. An isothermal oxidation experiment of 7YSZ TBCs is carried out in the atmosphere of 950 °C in order to simulate the high-temperature oxidation process of engine blades. The isothermal oxidation process of 7YSZ thermal barrier coatings is investigated systematically by impedance spectroscopy. The electrochemical physical model and equivalent circuit of columnar 7YSZ coatings are established. Results show that the isothermal oxidation kinetic curve of columnar 7YSZ thermal barrier coatings appears to follow the parabolic law. A pretreatment of bond coating can reduce the growth rate of the thermally grown oxide(TGO) layer, restraining the initiation and propagation of microcracks between YSZ and TGO layers. The oxidation rate constants of 7YSZ coatings with pretreated and un-pretreated bond coating are 0.101×10~(-12) cm~2·s~(-1) and 0.115 × 10~(-13) cm~2 ·s~(-1), respectively. Impedance analysis shows that the content of oxygen vacancies decreases and the density increases after the TGO layer is oxidized for 150 h. In addition, shrinkage microcracks formed by sintering during the oxidation process is the main reason for an increase of the capacitance and a decrease of the resistance in the grain boundary of YSZ.     

Ni47Ti44Nb9形状记忆合金耐蚀性能和抗氧化性能研究

采用高温氧化、电化学腐蚀测试,并结合SEM,XRD等分析手段,研究了Ni47Ti44Nb9合金的氧化性能和抗腐蚀性能。结果表明,Ni47Ti44Nb9合金在450℃下氧化非常轻微,600～800℃下合金的氧化增重曲线近似符合抛物线规律。经高温氧化后,合金表面形成的氧化层具有分层结构,氧化截面由外氧化层和过渡层组成。电化学腐蚀结果表明,溶液中NaCl含量越低,溶液温度越低,合金的腐蚀电流密度越小,腐蚀电位正移,保护膜的稳定性提高。     

Oxidation Properties in CO2 of Inconel Alloy 600 Coated by Simultaneous Aluminizing-Chromizing Process

IN 600 alloy was coated with two different types of coatings, Cr-modified aluminide coating this is called aluminizing-chromizing and Y-doped chromium modified aluminide coating this is called aluminizing-chromizing-yttriumizing. Diffusion coating was carried at 1 050 ℃ for 8 h under Ar atmosphere by simultaneous aluminizing-chromizing process and by simultaneous aluminizing-chromizing- yttriumizing. Cyclic oxidation tests were conducted on the uncoated and on the coated Inconel 600 alloy in the temperature range 800- 1 000 ℃ in CO2 for 100 h at 10 h cycle.The results showed that the oxidation kinetics for uncoated Inconel 600 alloy in CO2 is parabolic and the phases present are NiO, (Fe, Cr)2O3 , NiFe2O4 and NiCrO4. The oxidation kinetics for both coated systems in CO2 was found to be parabolic and the value of kP for both coated systems were found to be lower than that for uncoated Inconel 600 alloy. Oxide phases that formed on coated systems are Al2O3 and NiCrO4. The role of yttrium can be attributed to its ability to improve the adherence of the oxide scale.     

固体火箭发动机HTPB推进剂燃速性能老化研究

为研究某型固体火箭发动机高燃速端羟基聚丁二烯(HTPB)推进剂在全寿命期内的燃烧性能——燃速,通过高温加速老化实验和活化能理论推测出发动机推进剂在常温25℃下和高温70℃下的老化速度;由此,通过高温70℃的加速老化实验来获得不同贮存期的发动机推进剂试验样本;通过推进剂燃烧实验,测试了不同贮存期的推进剂的燃速,结果表明,随着发动机贮存时间的延长,HTPB推进剂燃速逐渐降低。     

驻涡燃烧室发散冷却方案试验

设计了两种适用于驻涡燃烧室的发散冷却结构,发散孔的倾角分别为30?和150?,并通过试验研究了两种冷却结构在不同位置处,不同温比及吹风比条件下的冷却效果.试验结果表明,两种冷却结构均具有较高的绝热效率;两种结构的绝热效率随主流温度或吹风比的变化规律相同;凹腔前壁面的绝热效率最高,后壁面的绝热效率最低;在相同试验条件下,倾角150?冷却结构的绝热效率高于倾角30?冷却结构的绝热效率;随着冷却气量的减小,两者之间的差距逐渐增大.最后,通过数值计算方法对试验结果进行了分析.      

Microstructure and Oxidation Behavior of Modified Aluminide Coating on Ni3Al-based Single Crystal Superalloy

Al, Al-Si and Cr-Al-Si coatings are prepared onto IC20 alloy by powder pack cementation to improve the oxidation resistance of the alloy. The isothermal oxidation behaviors of the coatings and the uncoated IC20 alloy at 1 100 °C are comparatively investigated. For the coatings, less weight gains are obtained compared to the uncoated alloy after 100 h thermal exposure. The Al-Si coating exhibits the best oxidation resistance, while the addition of Cr accelerates the scale spallation. Phase transformation from β-NiAl to γ and γ′ occurs in the coating after oxidation for extended periods. The oxidation protection and degradation mechanisms for these coatings are discussed.     

进气角度对旋转盘冷却效果的影响

为了研究不同的预旋角度对高位进气转静系旋转盘冷却与换热特性的影响,分别在三种预旋进气角度(0°,15°,30°)下对转盘的冷却效果进行了试验。通过试验,得到了每种预旋角度下的温度分布、盘面局部努赛尔特数分布、盘面平均努赛尔特数、转盘无量纲总体平均温度和转盘无量纲径向平均温差等参数。试验结果显示:高位垂直进气的冷却效果最好,预旋15°次之,预旋30°最低。并且流量变化对转盘的冷却效果影响较大,而转盘旋转影响较小。     

Thermal Fatigue Behavior of Ni_3Al Based Superalloy IC6E

The thermal fatigue behavior of Ni3Al based superalloy IC6E during the cycles between 900 ℃/1 000 ℃ and the room tempera-ture was investigated. The experimental results indicate that the primary and secondary thermal fatigue cracks initiate inside or round the borides and then spread away along grain boundaries and/or in interdendritic areas. The fracture of borides and their separation from the matrix at interfaces are mainly responsible for the crack initiation and its spreading. At temperatures higher than 1 000 ℃, the grain boundary oxidation combined with cyclic stresses accelerates the crack growth.     

Effects of different aging treatments on microstructures and mechanical properties of Al-Cu-Li alloy joints welded by electron beam welding

Post-weld single aging treatment(solution treatment at 510 ℃ for 1 h, water quenching,and aging at 155 ℃ for 16 h) and post-weld double aging treatment(solution treatment at 510 ℃ for 1 h, water quenching, aging at 155 ℃ for 16 h, and aging at 130 ℃ for 12 h) are carried out on Al-Cu-Li alloy joints by electron beam welding(EBW) respectively. The effects of aging treatments on microstructures and mechanical properties of welded joints are investigated. Results show that the mechanical properties of welded joints are obviously improved after both aging treatments. The strength coefficient of joints is increased from 0.64 in an as-welded condition(AW) to 0.90 after post-weld double aging treatment. Microstructure analysis shows that the precipitates of the fusion zone within grains and grain boundaries are less in the AW condition. After post-weld heat treatment(PWHT), a lot of fine needle-like phases T_1(Al_2 Cu Li) precipitate in grain boundaries of the fusion zone, and more horseshoe-shaped β' (Al_3 Zr) particles precipitate within grains. In addition,grains of the fusion zone are refined after post-weld double aging treatment, which leads to an effect of grain refinement strengthening. Consequently, the mechanical properties of welded joints are greatly improved.     

Thermal stability improvement of sprayable fast-responding pressure-sensitive paint for measurement above 100 °C

The thermal stability of sprayable fast-responding Pressure-Sensitive Paint (fast PSP) was investigated to explore the possibility for application in turbomachinery and hypersonic research with temperature above 100 °C. The first part of the study focused on a widely-used Polymer Ceramic PSP (PC-PSP). The effects of thermal degradation on its key sensing properties, including luminescent intensity, pressure sensitivity and response time, were examined for a temperature range from 60 to 100 °C. Severe degradation in intensity and pressure sensitivity was found as temperature reached 70 °C or higher, which would cause failure of PSP application in these conditions. Subsequently, a fast-responding Mesoporous-Particle PSP (MP-PSP) was developed which did not show degradation effects until 140 °C. The greatly improved thermal stability of MP-PSP was attributed to: selection of polymer with higher glass transition temperature (polystyrene) to delay the saturation effect of oxygen quenching as temperature increased; porous and hollow structure of particles for luminophore deposition that minimizes polymer–luminophore interaction. This new paint formulation has significantly raised the upper temperature limit of fast PSP and offers more opportunities for applications in harsh environment.     

大湍流度对超低雷诺数下翼型受力及绕流的影响

实验测量了超低雷诺数(Re=5 300)下 NACA 0012翼型在自由来流下的升力系数和阻力系数,重点研究来流的湍流度对升力系数和阻力系数的影响,并进一步通过对翼犁流场的研究揭示湍流度对翼型受力产生影响的机理.结果显示,低湍流度下升力系数和阻力系数均无失速特征;当湍流度提高,升力系数和阻力系数在12°～15°迎角下表...     

Corrosion Inhibition of SiC_p/5A06 Aluminum Metal Matrix Composite by Cerium Conversion Treatment

This article studies the effects of the CeCl₃ concentrations in conversion solutions with and without addition of NaCl, pH-values of conversion solution, drying temperature, time and temperature of immersion on the Ce-conversion coatings for corrosion protection of the SiC_p/5A06 Al-MMC and 5A06 Al-alloy in the 3.5% NaCl aqueous solution at room temperature. Potentiodynamic polarization tests reveal that the Ce-conversion treatment could markedly improve the pitting corrosion resistance of the composite and the matrix alloy in chloride containing environment. The best corrosion resistance effects are obtained for the samples treatment in 1‰ CeCl₃·7H₂O/ 3.5% NaCl solution at 45 °C for 60 min, followed by drying at 100 °C for 30 min. Examinations by means of scanning electron microscopy (SEM), energy dispersion spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS) indicate that this behavior is due to the precipitation of Ce-oxides/hydroxides on the cathodic intermetallics and the Al-oxide film on the rest of the metal matrix.     

0Cr15Ni5Cu2Ti钢的高温氧化行为

 采用增重法研究了0Cr15Ni5Cu2Ti钢在500,600,700和800 ℃下的高温氧化行为。利用扫描电镜（SEM）、能谱分析（EDS）、X射线衍射分析（XRD）以及金相显微分析等技术,对氧化膜的形貌、化学形态和组成以及基体组织的特点进行了研究。试验结果表明,在700 ℃以下,0Cr15Ni5Cu2Ti钢的氧化动力学符合抛物线规律,表面生成的氧化膜具有良好的保护性。800 ℃氧化时,随氧化膜厚度的增加内应力迅速增大,氧化膜容易破裂,甚至剥落;不锈钢基体中发生马氏体向奥氏体的逆转变,使贫铬层厚度增加,促进了失稳氧化发生,导致试样表面局部区域容易生成氧化物“瘤”,而加剧氧化。     

Temperature effect on buckling properties of ultra-thin-walled lenticular collapsible composite tube subjected to axial compression

This paper seeks to outline the temperature effect on the buckling properties of ultra-thin-walled lenticular collapsible composite tube(LCCT) subjected to axial compression.The buckling tests of the LCCT specimens subjected to axial compression were carried out on INSTRON-500 N servo-hydraulic machine in dry state and at the temperatures of 25 C, 100 C and 80 C. The load–displacement curves and buckling initiation loads were measured and the buckling initiation mechanism was discussed from experimental observations. Experiments show that the buckling initiation load, on average, is only about 2.2% greater at the low temperature of 80 C than at the room temperature of 25 C due to the material hardening, demonstrating an insignificant increase in the buckling initiation load, whereas it is about 19.5% lower at the high temperature of 100 C than at the room temperature owing to the material softening, implying a significant decrease in the buckling initiation load. The failure mode of the LCCT in axial compression tests at three different temperatures can be reckoned to be characteristic of the buckling initiation and propagation around the central region until rupture. The finite element(FE) model is presented to simulate the buckling initiation mechanism based on the eigenvalue-based methodology. Good correlation between experimental and numerical results is achieved.