基于预估-反馈联合处理的射频噪声干扰抑制算法

针对强射频（RF）噪声干扰下脉压雷达目标检测概率较低的问题,提出了一种基于预估-反馈联合处理的射频噪声干扰抑制算法。首先,对回波信号进行盲源分离预处理,并利用分数阶傅里叶变换（FRFT）的特性对目标回波信号进行参数估计以及窄带滤波处理,滤除大部分干扰和噪声的能量;然后,在数据层运用M/N逻辑法进行点迹处理,并结合径向速度方向判决,实现对目标航迹的预估检测;最后,利用数据层对航迹状态的反馈实时修正滤波器参数,从而在信号层更好地滤除干扰能量,并对中断航迹进行剔除,完成射频噪声干扰的抑制。仿真结果表明：与现有射频噪声干扰抑制技术相比,所提算法具有更优的干扰抑制效果。     

基于误码率准则的窄带干扰抑制算法性能分析

采用有效的窄带干扰抑制技术,可极大地改善扩频通信系统的性能.首先详细介绍了频域干扰抑制算法的基本思想,给出了算法实现的模块框图;其次具体分析了算法实现的关键技术：重叠加窗,背景噪声估计,干扰门限确定及干扰消除策略;最后以误码率作为干扰消除算法性能的评判标准,仿真分析了频域窄带干扰抑制技术中干扰强度、干扰频带宽度、干扰频率位置、干扰消除门限、陷幅值、加窗重叠度等因素对系统误码率的影响,为在不同条件下算法最佳参数的选取提供了依据.仿真结果表明：当干扰消除门限值取4aF,陷幅值取2σF～6σF,加窗重叠度为50％时,该算法可获得最佳抗干扰性能.     

一种多系统兼容卫星导航抗窄带干扰专用芯片设计

卫星导航信号由于其自身特点,经过长距离传输到达地面信号功率十分微弱,所以很容易受到外来同频窄带信号干扰。主要介绍了一种满足北斗、GPS多系统兼容的卫星导航抗窄带专用芯片的设计方案。其采用模数转换、抗干扰处理集成单颗芯片设计架构,可直接替换原有卫星导航终端的A/D芯片,实现抗窄带干扰功能;并着重对抗干扰算法的多系统兼容设计、低功耗干扰检测技术进行了介绍;经流片测试,该芯片抗北斗B1、B3频点和GPS L1频点窄带干扰干信比大于60d B,北斗S频点抗窄带干扰干信比大于55d B,双路同时工作最大功耗小于260m W,可有效满足手持、车载、弹载等小型低功耗卫星导航终端的应用需求。     

基于apFFT的罗兰-C窄带干扰频域抑制方法

针对现有罗兰-C接收机普遍采用固定陷波电路抑制窄带干扰的情况,提出了基于全相位谱分析(apFFT)的频域精确自适应陷波罗兰-C窄带干扰抑制方法,设计了基于双相移组合全相位法的FIR频域陷波器。在对窄带干扰进行精确谱分析的基础上,设计相应频点的陷波器对多个窄带干扰进行抑制。基于MATLAB的仿真结果表明:该方法能够根据罗兰-C窄带干扰频率的变化,实现频点任意控制的频域自适应陷波,有效恢复出罗兰-C信号,为增强型罗兰-C接收机的设计提供了一种简单有效的窄带干扰抑制方法。     

自适应干扰对消在扩频抗窄带干扰中的应用

讨论了自适应对消实现扩频抗窄带干扰的基本原理,并进行了仿真实验,得出了采用干扰跟踪器来提高对消效果的结论.在航天704所开发的扩频应答机样机上进行了抗窄带干扰实验,结果表明：在扩频接收机中采用自适应对消器以及干扰检测和跟踪器后,至少可以做到43dB的抗窄带干扰能力.     

GPS信号FFT自适应抗干扰技术的FPGA工程实现

针对自适应抗干扰技术展开研究,提出了易于FPGA实现的FFT自适应窄带抗干扰技术.这种方法减小了数字信号处理部分的计算量,提高了系统处理的实时性,降低了系统的复杂程度.实验表明在有宽带干扰存在的情况下,使用所提出的方法可以自适应检测并剔除窄带干扰.与GPS接收机的对接测试表明,该技术能大大提高接收机的抗干扰能力.     

基于四阶累积量和小波降噪的干扰抑制算法

针对盲信号分离算法在低信噪比下分离效果较差的情况,提出了一种基于四阶累积量和小波降噪的含噪盲分离算法,并将该算法用于卫星通信干扰抑制。首先,利用基于四阶累积量的盲分离算法进行信扰盲分离;然后对分离出的已被噪声污染的通信信号进行小波降噪处理。最后,对提出的算法在单音干扰下进行了性能仿真。仿真结果表明,该算法不仅使抗噪性能提高了3dB左右,而且在低信噪比下对强单音干扰具有较好的抑制效果。     

GNSS干扰信号检测方法研究

研究了GNSS导航接收机在干扰源条件下的干扰检测和识别技术。除常见的卫星干扰如脉冲干扰、扫频干扰、BPSK干扰、宽带高斯白噪声干扰外,还添加了QPSK和8PSK干扰进行建模分析,并提取了常见的特征参数,如信号3dB带宽和频谱峰度等。通过研究,高阶累积量被提取作为MPSK干扰类内识别的特征参数。研究了基于决策树和BP神经网络等分类器算法的干扰盲识别,并分析比较了这些分类算法的识别准确率,为抗干扰领域的研究提供了重要参考。     

基于概率统计的DS/FH系统干扰检测算法

基于时频分布的干扰检测算法是DS/FH（Direct Sequence/Frequency Hopping,直接序列扩频/跳频扩频）系统干扰检测的传统手段,针对其运算量大、实时性差,以及无法检测某些特殊干扰信号等问题,提出一种基于概率统计的干扰检测算法.通过统计DS/FH系统频谱图中各频率的幅值出现位置,以DS/FH信号与干扰信号频谱分布规律的差别为判决依据,完成DS/FH系统中干扰信号的检测.分析和仿真结果表明：该检测算法能够有效识别DS/FH系统中的典型干扰信号,与传统基于时频分布的检测算法相比,能够实现某些特殊干扰信号的有效检测;同时,由于该算法不需要进行复杂的时频联合分析,其运算复杂度大大降低,能够实现DS/FH系统干扰信号的快速检测.     

自适应滤波抑制电子设备窄带干扰的研究

针对电子设备内部、外部普遍存在的窄带干扰问题,提出了采用自适应滤波的手段抑制这种干扰信号的设想,分析了其抑制扩频信号多窄带干扰的性能,并对其做出了理论论证。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.