溶胶-凝胶法制备SiO2 -TiO2 / 聚酰亚胺杂化材料及其性能

采用溶胶-凝胶法制备了纳米SiO2-TiO2溶胶,然后通过共混法制得SiO2-TiO2/聚酰亚胺杂化材料,SEM、DMTA和TGA等方法研究了无机组分的含量对聚酰亚胺性能的影响。结果表明:SiO2-TiO2/聚酰亚胺杂化材料的冲击强度和弯曲强度随无机粒子含量变化而变化,当无机粒子含量为3%(质量分数)时二者出现最大值,其冲击强度较纯树脂提高了177%,弯曲强度提高了54.6%。另外,随着SiO2-TiO2无机材料的增加,杂化材料热稳定性亦有所提高。     

Fe_2O_3掺杂原位合成Al_2O_3/TiAl复合材料的组织与性能

利用Ti-Al-TiO2-Fe2O3体系的放热反应,原位热压合成了Fe掺杂的Al2O3/TiAl复合材料。借助XRD和SEM研究了复合材料的物相组成和显微结构以及Fe2O3引入量对复合材料结构和力学性能的影响。结果表明:产物主要由γ-TiAl,α2-Ti3Al,Al2O3相构成,Al2O3颗粒分布于基体交界处,存在一定的团聚;随Fe2O3的掺杂量增大,Al2O3颗粒呈细小弥散分布,同时基体晶粒尺寸也减小,较好地改善了材料的力学性能,复合材料的相对密度和洛氏硬度逐渐增大。Fe2O3掺杂量为0.84%(质量分数)时,复合材料弯曲强度和断裂韧度达到最大值,分别为624MPa和6.63 MPa·m1/2。     

硅烷偶联剂改性Al2 O3p/TDE-85 的力学性能

利用硅烷偶联剂对Al2O3颗粒进行表面改性,制备了Al2O3颗粒增强的TDE-85树脂基复合材料,研究了表面改性对其力学性能的影响,采用差热分析仪测定复合材料的固化反应温度,并计算了固化反应活化能。利用扫描电子显微镜分析了拉伸断口形貌。研究发现,当Al2O3用量为2wt%时,固化反应速度较快,硅烷偶联剂用量为4wt%时,冲击强度为13.2 kJ/m2;拉伸强度为65.2 MPa;弹性模量为2.66 GPa;最大伸长率为3.35%,此时对Al2O3颗粒的表面改性综合效果最好。     

热处理对Pt-PtRh13薄膜热电偶绝缘层性能的影响及机理分析

为了测量航空发动机高温部件表面温度,利用离子束溅射镀膜技术制备了拥有多层薄膜结构的Pt-PtRh13薄膜热电偶,包括Ni基合金基底、Ni Cr Al Y黏结层、Al2O3过渡层、Al2O3绝缘层、Pt/Pt Rh13薄膜热电偶和Al2O3保护层。研究了热处理对Pt-PtRh13薄膜热电偶绝缘层性能的影响,并利用扫描电子显微镜(SEM)、X射线衍射分析(XRD)等手段对薄膜热电偶绝缘层性能下降的机理进行了分析。研究结果表明:利用Al2O3绝缘薄膜开发的Pt-PtRh13薄膜热电偶只用于900℃以下测温,在900℃以上长时间应用可能会出现测温不稳定问题,高温诱发Al2O3绝缘层发生晶型转变是主要原因。     

反应烧结制备六方氮化硼陶瓷

解决六方氮化硼的难烧结性,是提高其性能的关键.本文探讨了以硼粉为基体,Y2O3,、Al2O3为添加剂,在N2气氛下,反应烧结制备六方氮化硼陶瓷的工艺过程.研究结果表明,硼粉和氮气反应剧烈进行的温度区间在1 050～1 350℃,在1 550℃反应得到进一步完善.当烧结助剂的质量分数为20%,且w(Al2O3):w(Y2O3)=3:2,1 850℃保温2 h,试样有较高强度及较低气孔率,且h-BN晶粒形状大小分布均匀.     

ZrO2对C/Al2O3陶瓷多功能复合材料性能的影响

采用基体改性的方法,向AlCl3溶胶中添加ZrO2粉,制得含ZrO2的C/Al2O3复合材料,探讨了添加ZrO2对C/Al2O3多功能复合材料性能的影响.结果表明添加少量的ZrO2,可产生基体的相变及在基体内产生微裂纹,这可改善C/Al2O3陶瓷基体间界面性能,提高材料强度,降低材料热导率.同时对ZrO2添加量进行了优化处理,最终确定ZrO2的最佳含量为1%(质量分数),使材料强度值提高39%,材料热导率降低至0.902 W/(m·K)以下.     

亚微米晶NiAl-Al2O3复合材料的制备及其烧结-锻造短流程成形

以Ni粉和Al粉为原料,通过机械合金化和真空热压烧结制备了高致密的NiAl-5％Al2O3(体积分数,下同)复合材料,并利用烧结-锻造技术制成了该材料的前缘模拟件.机械球磨后,粉末颗粒充分细化,Ni和Al发生原位反应,并最终生成NiAl-5％Al2O3复合材料粉末.经1300℃真空热压烧结,获得致密的NiAl-Al2O...     

原位反应合成Nb掺杂Al2O3/TiAl复合材料的显微结构分析

利用Al-Ti-TiO2体系原位反应合成了Nb掺杂Al2O3／TiAl复合材料。借助XRD和SEM研究了Nb掺杂Al2O3／TiAl的显微结构以及Nb引入量对复合材料显微结构的影响。结果表明，复合材料由TiAl、Ti3Al、Al2O3、Nb和NbAl3相构成，细小Al2O3颗粒分布于基体晶粒交界处，存在一定的团聚；Nb元素引入量的高低，可调节产物中TiAl和Ti3Al的相对含量，随Nb含量的增大，TiAl含量逐渐减少，Ti3Al则逐渐增大；同时，基体晶粒和Al2O3颗粒均有所细化，且分布逐渐均匀，材料的均匀性得到改善。     

周期换向脉冲法快速电沉积 Al2 O3／Ni 复合镀层

以 Al2 O3微粒为分散相,进行了周期换向脉冲复合电沉积工艺研究,快速电沉积出了 Al2 O3／Ni 复合镀层。利用扫描电镜及能谱分析技术对 Al2 O3／Ni 复合镀层的微观形貌及组成进行了表征,考察了脉冲参数对复合镀层中Al2 O3含量及镀层微观形貌的影响;并就周期换向脉冲电沉积与直流电沉积复合镀层的微观形貌、镀层应力及沉积速率进行比较。结果表明：采用周期换向脉冲法快速电沉积可以得到组织致密、内应力小、沉积速率高的 Al2 O3／Ni复合镀层。     

热压压力对B/Al复合材料组织结构及力学性能的影响

使用表面覆有B4C涂层的硼纤维，采用大气等离子喷涂法制备连续硼纤维增强铝基复合材料预制片，结合真空热压扩散焊制备了纤维均匀分布的B／Al复合材料。探讨在接近铝基体熔点温度的条件下热压压力对复合材料力学性能与B／Al界面结合的影响，分析了B／Al界面结合状态与断口形貌及力学性能之间的关系。研究表明：热压压力对制备的B／Al复合材料的纤维体积分数、B纤维与Al基体的界面结合状态和拉伸强度有显著的影响；纤维表面的B4c涂层有效地防止了B纤维与Al基体间的界面反应，在温度6500C、压力10MPa的条件下，制备的纤维体积分数为42％的B／Al复合材料拉伸强度达到968MPa，达到了纤维理想强度的77％。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.