High Power Radar Implementation of Coherent Waveforms

The radar use of coherent burst waveforms to obtain clutter suppression is summarized and problems arising from the high power implementation of such waveforms are discussed. These problems arise from the nonlinear nature of the typical high power radar transmitter and result in loss of subpulse-to-subpulse amplitude and phase accuracies, causing clutter suppression degradation. adaptive control loop used to measure transmission errors and provide continuous updating to minimize such errors is proposed. Residual transmission errors resulting via use of the control loop are calculated and shown to have an insignificant effect upon the clutter suppression properties of the coherent waveform. Experimental verification of control loop performance is presented.     

SAR resolution in the presence of phase errors

The author analyzes the effects of phase errors on synthetic aperture radar (SAR). The theory is applied to the following question: how does the achievable resolution vary with the carrier frequency when optimum quadratic focus and/or optimum processing interval (synthetic aperture length) are used? Numerous related results are given, so that much of the material is tutorial. For phase errors corresponding to uncompensated motion, the best achievable RMS resolution with any phase error spectrum satisfies the derived equation. For motion-induced phase errors it is seen that resolution improves with increasing carrier frequency when the first term in the expression applies (e.g. for phase errors concentrated at low frequencies) and resolution is independent of carrier frequency when R δ/v/v is the smaller term (e.g. with broad band or high frequency phase errors)     

Synthetic Aperture Radar

The general theory of side-looking synthetic aperture radar systems is developed. A simple circuit-theory model is developed; the geometry of the system determines the nature of the prefilter and the receiver (or processor) is the postfilter. The complex distributed reflectivity density appears as the input, and receiver noise is first considered as the interference which limits performance. Analysis and optimization are carried out for three performance criteria (resolution, signal-to-noise ratio, and least squares estimation of the target field). The optimum synthetic aperture length is derived in terms of the noise level and average transmitted power. Range-Doppler ambiguity limitations and optical processing are discussed briefly. The synthetic aperture concept for rotating target fields is described. It is observed that, for a physical aperture, a side-looking radar, and a rotating target field, the azimuth resolution is ?/? where ? is the change in aspect angle over which the target field is viewed, The effects of phase errors on azimuth resolution are derived in terms of the power density spectrum of the derivative of the phase errors and the performance in the absence of phase errors.     

Digital beamforming calibration for FMCW radar

Three sources of beamforming deterioration are identified for an FMCW radar. These all relate to time-of-arrival and cable delays. There are small range-dependent phase errors at the receiver outputs. The delays cause frequency shifts, which produce phase errors at the discrete Fourier transform (DFT) outputs after ranging. These frequency shifts cause amplitude errors when the signals are resolved into the same range bin. Two methods of compensating for phase and amplitude errors are proposed. The first corrects for phase errors prior to beamforming. Amplitude errors are ignored but the residual error is usually small. The second method aligns the receiver frequencies digitally before ranging. This eliminates the phase errors and the amplitude errors at the DFT range estimates     

Analysis of the Switched Self-Balancing Comparsion Radiometer

Analysis of the switched self-balancing comparison radiometer with coupling between the channels is given. The comparison source is a stationary, zero-mean white noise generator of known spectral density. An expression for the power spectrum at the output of the radiometer is derived. It is shown that measurement errors due to interchannel coupling can be corrected by phase switching. Radiometer sensitivity is also calculated. The switched version of the radiometer has been simulated at low frequencies and is under construction at X-band.     

Phased array of large reflectors for deep-space communication

In this paper the problem of uplink array calibration for deep-space communication is considered. A phased array of many modest-size reflectors antennas is used to drastically improve the uplink effective isotropic radiated power of a ground station. A radar calibration procedure for the array phase distribution is presented using a number of in-orbit targets. Design of optimal orbit and the number of calibration targets is investigated for providing frequent calibration opportunities needed for compensating array elements phase center movements as the array tracks a spacecraft. Array far-field focusing based on the near-filed in-orbit (low Earth orbit (LEO)) calibration targets is also presented and array gain degradation analysis based on the position error of the array elements and in-orbit targets has been carried out. It is shown that errors in the in-orbit targets positions significantly degrade the far-field array gain while the errors in array elements positions are not very important. Analysis of phase errors caused by thermal noise, system instability, and atmospheric effects show insignificant array gain degradation by these factors     

Polarization Mismatch Errors in Radio Phase Interferometers

An analysis is presented which deals with the effects of polarization mismatch errors on the accuracy of a phase interferometer used for position location of unknown emitters relative to known calibration emitters. Closed-form expressions for the induced phase difference between interferometer antennas are derived for several combinations of receiving and transmitting antenna polarizations. Errors contributed by mechanical misalignment between antennas, as well as effects of power loss attributable to polarization mismatch, are also considered. The analysis leads to the conclusion that circularly polarized interferometer and transmitter antennas are best suited for the position location application, if it is assumed that polarization tracking of the interferometer antennas is not available. It is shown that a reasonable amount of ellipticity can be tolerated before the phase error becomes significant.     

射频仿真幅相控制误差对目标位置精度的影响分析

在射频仿真系统中,精确的目标位置通过“三元组”幅相控制实现,幅相控制误差直接影响阵列上目标位置的模拟精度。详细推导了角闪烁方程,以此建立了幅控误差传播模型,提出了相控误差传播的等效分析方法,分析了幅相控误差对目标位置精度影响的基本规律。基本分析结论经仿真验证正确,具有工程指导意义。     

惯导装置精度试验火箭橇弹道设计

以9km 火箭橇试验设施为基础, 就惯导装置精度试验所需的长时、大过载 弹道条件, 提出了一种火箭橇弹道的设计方法。建立了火箭橇主动段和刹车段运动方 程, 针对火箭发动机推力、气动力、摩擦力和刹车力等主要动力学因素, 结合工程经 验,提出了选取原则和方法。以某惯导装置精度试验为背景,设计了火箭橇试验弹道, 通过试验验证,设计结果与实测数据基本一致,满足总体要求,并对其中出现的主要误 差进行了分析和评估。该研究能够为惯导装置开展精度试验奠定良好的火箭橇弹道设计 基础。     

Error Analysis of the Optimal Antenna Array Processors

The optimal weights of an antenna array processor, which maximizes the output signal-to-noise ratio (SNR) in the absence of errors, are computed using the noise-alone matrix inverse (NAMI) and the steering vector in the look direction or the signal-plus-noise matrix inverse (SPNMI) and the steering vector. In practice the estimated steering vector as well as the estimated optimal weights are corrupted by random errors. This paper has analyzed the effects of these errors on the performance of the NAMI processor and the SPNMI processor by deriving analytic expressions for the output signal power, output noise power, output SNR, and the array gain as a function of the error variance. The treatment is for a general array configuration and no assumption about a particular array geometry is made.     

Analysis and design optimization of monopulse receivers forsecondary surveillance radar

The sensitivity to calibration and component errors of the receiver configurations used for monopulse processing of secondary surveillance radar (SSR) replies is analyzed. The effects of video gain error in amplitude processors and large Gaussian perturbations in phase processors are discussed. Phase processors are shown to be robust to variations in antenna difference pattern null depth. A half-angle phase processor that yields the benefits of phase processing without the sensitivity to system errors associated with conventional implementations is described     

Performance Analysis of the Modulation Cancellation Altimeter

The performance of the modulation cancellation altimeter is investigated. Several sources of error are considered, specifically: 1) terrain averaging error; 2) output noise fluctuations; 3) errors due to phase shifts; and 4) acquisition ambiguities. The predominant parameters affecting these errors are investigated with a view towards optimizing the performance of the altimeter.     

双基地聚束SAR运动误差分析

将三维坐标系引入运动误差分析,建立了对任意匀速直线航迹双基地聚束SAR运动误差统一、清晰的分析方法;在此三维坐标系下,推导出各种运动误差引起的相位误差的计算公式。推导基于一般的双基地聚束SAR回波模型,可适用于任意匀速直线航迹的双基地聚束SAR,并且将通常的单基地SAR的运动误差分析作为一种特例也涵盖在内。给出了位置误差、速度误差和加速度误差所造成的相位误差计算公式。从推导结果得出结论:位于不同平台的同一误差,引起的相位误差是不同的;在小场景假设下,双基地聚束SAR的运动误差是空不变的,与目标位置无关。计算机仿真验证了误差分析的正确性。     

Strapdown inertial measurement units for motion compensation forsynthetic aperture radars

It is shown that synthetic-aperture radar (SAR) motion can be compensated by using an antenna-mounted strapdown inertial measurement unit (IMU) as the motion sensing system, but sensor and system errors affect SAR image quality. A strapdown IMU consists of three accelerator channels and three gyro channels. Strapdown IMU errors include gyro-scale and accelerometer-scale factor and bias errors, velocity error, platform tilt, and errors induced by limited inertial sensor bandwidth. The effects of these errors on the SAR image quality are presented in terms of the SAR impulse response. IMU errors that cause low-frequency phase errors (less than one cycle per array time) are categorized in terms of quadratic and cubic phase errors. IMU errors that cause high-frequency phase errors (greater than one cycle per array time) are categorized in terms of the integrated sidelobe ratio and peak sidelobe ratio. A motion compensation system conceptualization is described wherein a strapdown IMU is attached to an antenna and transfer-aligns to the aircraft's master navigator     

Adaptive Radar Beacon Forming

Propagation errors along paths between an array radar and a distribution of targets cause degradations in angle measurements and detection range. The overall objective of the research described in this paper was to analyze and demonstrate the use of conjugate reflections for compensating adverse effects of path errors. The effect of reflecting the conjugate of an incident wave is described mathematically and is demonstrated by computer simulation. Repeated conjugate reflections are shown to result in the formation of a single beam usually focussed on a target highlight. Echoes from this spatial reference, or "beacon" are shown to provide the means by which aperture phase errors may be effectively compensated. Results of radar simulations include two-way patterns computed for an example involving a distribution of three-point targets and half-wave-length Gaussian aperture errors. Without compensation a gain loss of 12 dB is computed; with error correction, based on echoes from an adaptively focussed beam, the two-way pattern is within a small fraction of a dB of the ideal pattern. The effect of noise on adaptive beacon forming was considered for a case involving one target. Repeated conjugate reflections improve signal-to-noise ratio as long as the effect of noise is less than the effect of aperture dephasing on the power reflected back to the target. An example is presented in which signal-to-noise ratio at the output of the receiver combining network is increased from 4 to 11.8 dB.     

轴对称火焰温度场的全息干涉计量

本文对轴对称位相物体的全息干涉计量中光线在位相物体中的折射引起的计量误差进行了计算分析,并且介绍了一种修正这种误差的简单方法。根据这一原理对酒精灯火焰和氢气火焰的温度分布进行了全息干涉计量。在干涉条纹的细化搜索中,采用了计算机图像处理方法。      

一种MIMO雷达幅相误差估计方法

 针对单基地相关多输入多输出(MIMO)雷达中存在的阵列幅相误差问题进行了研究。给出了单基地相关MIMO雷达的阵列模型,并提出了一种MIMO雷达幅相误差估计方法。利用发射正交信号对阵列接收信号进行匹配滤波,可分离得到类似传统阵列的"虚拟阵列",利用分时信源数据将该阵列中真实导向矢量中信源波达方向(DOA)引起的相位与幅相误差分离开,通过构造代价函数得到波达方向估计值,进而分别得到发射阵与接收阵的幅相误差的估计值,同时给出了误差引入量分析。最后通过仿真验证了该方法的有效性。本文介绍的方法简单可行,适用于任意构型MIMO雷达的幅相误差估计。     

弧齿锥齿轮功率分流传动系统建模与承载特性分析

针对齿轮功率分流的平行轴传动,星型传动和行星传动形式,提出了一种新型交叉轴传动形式的弧齿锥齿轮功率分流传动系统并介绍了其构成及工作状态.在此基础上,计算了系统各齿轮副的传递功率,分析了系统在各安装误差作用下的功率分流情况.研究表明,在输入齿轮、其相对的输出齿轮的轴交角误差或其相邻的输出齿轮的轴向误差单独影响下,系统主承载齿轮副传递的功率减小,可大大提高系统承载能力,并有利于功率分流均载;系统各齿轮都具有安装误差时,各齿轮副承载情况受误差累加或相反作用的影响.      

星载DBF接收天线误差校正算法

 提出了一种改进的基于子空间的星载数字波束形成（DBF）接收天线的误差校正方法。根据阵列互耦效应主要取决于阵元间的几何距离这一特点,利用阵元空间排布的对称性简化了天线的互耦模型,将天线的互耦效应及射频(RF)通道失配统一为通道间的幅相不一致。通过在基带注入特定的阵内相位差降低了子空间算法的计算复杂度。在建立7单元正六边形平面阵仿真模型的基础上,分析不同信噪比(SNR)环境下校正算法的性能,经比较得出可以通过提高发射信号功率改善误差估计的精度,验证了算法的有效性。仿真分析结果表明该算法在卫星通信系统中有一定的工程应用价值。     

Performance of phased-array antennas with mechanical errors

The performance of planar phase-array antennas with mechanical errors is investigated. Errors in array element positions as a result of structural distortions are considered as deterministic and predictable. Detailed calculations for two assumed modes of distortion reveal that their effects on antenna performance are the loss of peak response in the scan direction and the broadening of the mainlobe, while the far-out sidelobe structure remains relatively intact. For large antennas, performance improvement can be expected by suitable phase compensation. Performance of antennas with random errors in their element positions must be treated statistically. Expressions of average directivity and sidelobe level corresponding to arbitrary error magnitudes in element position, amplitude and phase of excitation as well as finite rate of failure of element modules were derived and verified by direct numerical calculations from the antenna directivity patterns. For a planar phased-array antenna typical for space-based radars, the standard deviation of element position errors must not exceed 1% of the operating wavelength in order to maintain a -10 dBi sidelobe level