Degradation of Signal-to-Noise Ratio Due to IF Filtering

A receiver for biphase modulated signals using an integrate-and-dump filter is optimum only if the IF filter bandwidth is infinite. Finite IF filter bandwidth results is a performance degradation. Using the predetection signal-to-noise ratio as the performance criterion, a lower bound on this quantity is determined as a function of the ratio (IF filter bandwidth)/(bit rate). The corresponding upper bound on the error probability is also presented.     

A hardware-efficient, multirate, digital channelized receiverarchitecture

An approach is presented to realizing a digital channelized receiver for signal intercept applications that provides a hardware efficient implementation of a uniform filter bank in which the number of filters K is greater than the decimation factor M. The proposed architecture allows simple channel arbitration logic to be used and provides reliable instantaneous frequency measurements, even in adjacent channel crossover regions. In the proposed implementation of the filter bank, K is related to M by K=FM where F is an integer. It is shown that the optimum selection of F allows the instantaneous frequency measurement to be made in the channel crossover region and the arbitration function to be based solely on the instantaneous frequency measurement. The development of a filter bank structure which combines the flexibility of the short-time Fourier transform (STFT) with the implementation efficiency of the polyphase filter bank decomposition, meeting these requirements and leading to a hardware-efficient implementation, is presented     

Degradation of Probability of Error Due to IF Filtering

The probability of error P(e) is computed in a binary communication system with a single-pole IF filter. The effect of time-bandwidth product foT and IF frequency to band width ratio f1/Ifo on P(e) is shown. The sampling time is optimized and the effect of nonoptimal sampling time on P(e) is calculated.     

Adjacent Channel Interference in a Binary Bandpass Communication System

The effect of adjacent channel interference on the probability of error in a binary bandpass communication system with an integrating and dumping detector is investigated. Narrowband filters are assumed in the receiver of the main signal and transmitters of both main and interfering signals. Plots of the probability of error as a function of signal to noise ratio in the main channel or as a function of carrier frequency difference between the main and interfering signals are presented, assuming that the filters are of the Butterworth type. These figures are helpful in the selection of minimal frequency spacing of adjacent channels.     

Binary Communication with Large Bandwidth to IF Frequency Ratios

The effect of I F filter bandwidth to I F frequency ratio on the probability of error in a binary bandpass communication system with nonreturn-to-zero (NRZ) and split-phase (SP) signals is investigated. ed. Explicit results are given for the case when the bandpas I F filter is transformed from a single-pole low-pass filter.     

Optimal and Suboptimal Perfomance of a PCM/FM Communication System

Theoretical results are presented on probability of error in the detection of binary FM signals for various frequency deviations with fixed bit rate, restricted predetection filter bandwidth, ideal limiterdiscriminator reception, and integrate-and-dump postdetection filter decision. The results show that suboptimal system performance can be achieved by choosing the largest possible value of deviation index which lies approximately at 0.7 + 2n, where n = 0, 1,...,k. k is determined by the reconstructability of signal after the bandpass filter.     

Effects of a Finite-Width Decision Threshold on Binary CPSK and FSK Communication Systems

The function of the receiver in a binary digital communication system is to make a binary (?space?, ?mark? or ?"0?, ?1?) decision by comparing the signal values from the mark and space filters (or correlators) at known successive time intervals (?bit? or ?baud? time intervals). When the signal value out of the mark filter is greater than that out of the space filter, it is decided that mark or 1 is transmitted, and vice versa. It is of fundamental importance to know the exact instant of time at which the two filter outputs are to be compared. This is the problem of synchronization between the transmitter and the receiver. In this paper, we assume a system that is perfectly synchronized. In a practical system, the difference between the two filter outputs must differ from a threshold by some finite amount in order to cause the device to respond reliably. The examination of the effects of this dead zone (finite-width decision threshold) on digital transmission systems is of important practical interest. Its effects on binary differentially coherent phase-shift-keying, and m-level phase-shift-keying systems have been investigated previously. In this paper we consider its effects on binary coherent phase-shift-keying (CPSK), coherent orthogonal (CFSK), and noncoherent orthogonal (NCFSK) systems. The probability of bit error and the channel capacity of each system is obtained in terms of the dead zone threshold.     

On the Acquisition Time for an Apollo Ranging Code

An Apollo ranging system is considered whose phase reference is obtained by a phase-locked loop for bit synchronization. The bit phase reference is noisy, and the error probability for the ranging code is shown to depend on the input signal energy per bit to noise density ratio. The procedure of computing the acquisition time for the ranging code is then presented and the acquisition time for a lunar ranging code is plotted versus the input signal-to-noise density ratio.     

Imperfect Carrier Recovery Effect on Filtered PSK Signals

Coherent demodulation of a PSK signal requires the generation of a local carrier phase reference. Methods are given to determine the detection loss caused by noisy phase recovery and its use in the coherent detection of filtered BPSK and QPSK signals. It is assumed that the phase noise can have a static part and a random component with a Tikhonov-type distribution. The static part is mostly due to offset frequency tracking of the PLL used to recover the carrier, while the random component is due to thermal noise present in the carrier recovery loop and is also due to the random nature of the phase modulation. It is shown that the probability of error of BPSK and QPSK can be expressed as a finite sum of a set of strictly alternating converging series when the number of ISI terms is finite. Upper and lower bounds on the probability of error have been derived when this number becomes infinite and we show how this error rate can be computed with any desired accuracy. Numerical results are presented for various values of static error and phase noise variance when the transmit and receive filters are 4-pole Butterworth filters. For filtered PSK signals and for a bit error rate of 10-6, our results show that the additional degradation in presentday receiver systems due to imperfect carrier recovery can be less than 0.1 dB for BPSK and less than 1 dB for QPSK.     

Subspace array processing for the suppression of FM jamming in GPS receivers

The mitigation of FM interference in GPS receivers is considered. In difference to commonly assumed wideband and narrowband interferers, the FM interferers are wideband, but instantaneously narrowband, and as such, have clear time-frequency (TF) signatures that are distinct from the GPS coarse acquisition (C/A) spread spectrum code. In the proposed technique, the estimate of the FM interference instantaneous frequency (IF) and the interference spatial signature are used to construct the spatiotemporal interference subspace. The IF estimates can be provided using existing effective linear or bilinear TF methods. The undesired signal arrival is suppressed by projecting the input data on the interference orthogonal subspace. With a multisensor receiver, the distinctions in both the spatial and TF signatures of signal arrivals allow effective interference suppressions. The deterministic nature of the signal model is considered and the known underlying structure of the GPS C/A code is utilized. We derive the receiver signal-to-interference-plus-noise ratio (SINR) under exact and perturbed IF values. The effect of IF estimation errors on both pseudorange measurements and navigation data recovery is analyzed. Simulation results comparing the receiver performances under IF errors in single and multiantenna GPS receivers are provided.     

On Signal and Noise Level Estimation in a Coherent PCM Channel

Joint maximum likelihood estimators are presented for the signal amplitude and noise power density in a coherent PCM channel with white Gaussian noise and a correlation receiver. The estimates are based upon the correlation coefficient outputs of the receiver. From these estimators, an estimator for the quantity (received signal energy)/bit/,(noise power)/(unit bandwidth) upon which the error probabilities depend, is derived. This estimator is shown to be useful as 1) a point estimator for the signal-to-noise ratio for the higher values of this ratio (about 4 dB or greater), and 2) an easily calculated statistic upon which to base data acceptance or rejection criteria. The acceptance or rejection levels are obtained by the use of confidence interval curves in conjunction with word error probability data.     

Poly-phase codes and optimal filters for multiple user ranging

A technique is introduced to select poly-phase codes and optimal filters of a pulse compression system that have specific temporal and frequency characteristics. In the particular problem under study, multiple vehicles are assigned unique codes and receiver filters that have nearly orthogonal signatures. Narrowband users, that act as interference, are also present within the system. A code selection algorithm is used to select codes which have low autocorrelation sidelobes and low cross correlation peaks. Optimal mismatched filters are designed for these codes which minimize the peak values in the autocorrelation and the cross correlation functions. An adjustment to the filter design technique produces filters with nulls in their frequency response, in addition to having low correlation peaks. The method produces good codes and filters for a four-user system with length 34 four-phase codes. There is considerable improvement in cross and autocorrelation sidelobe levels over the matched filter case with only a slight decrease in the signal-to-noise ratio (SNR) of the system. The mismatched filter design also allows the design of frequency nulls at any frequency with arbitrary null attenuation, null width, and sidelobe level, at the cost of a slight decrease in processing gain     

Signal Resolution via Digital Inverse Filtering

Research in numerous areas is directed toward the resolution of multiple overlapping signals in a noisy environment. These areas include radar, sonar, speech, seismology, and electrophysiology. Sometimes matched filters are used; other times inverse filters are employed. This paper discusses one approach to the analysis of the resolution of inverse filters. Our method is to compromise the trade-off between signal resolution and the output signal-to-noise ratio (SNR). A performance measure for the inverse or deconvolution filter is defined as a quantity proportional to the harmonic mean of the resolution and the SNR. An optimum output pulse duration is obtained using this criterion, where the pulse shape has been previously selected and the input signal waveform is known. In addition, upper and lower bounds for the output pulse duration are presented. Graphs are given which allow the designer to select the optimum inverse filter output pulse duration for a desired signal resolution and an estimated SNR.     

The Effect of a Pulsed Interference Signal on an Adaptive Array

The performance of a least mean square (LMS) adaptive array in the presence of a pulsed interference signal is examined. It is shown that a pulsed interference signal has two effects. First, it causes the array to modulate the desired signal envelope (but not its phase). Second, it causes the array output signal-to-interferenceplus-noise ratio (SINR) to vary with time. The desired signal modulation is evaluated as a function of signal arrival angles, powers and interference pulse-repetition frequency (PRF) and pulsewidth. It is shown that the signal modulation is small except when the interference arrives close to the desired signal. To evaluate the effect of the time-varying SINR, it is assumed that the array is used in a differential phase-shift keyed (DPSK) communication system. It is shown that the SINR variation causes a noticeable but not disastrous increase in the bit error probability.     

Adaptive Maximum Likelihood Receiver for Direct-Ranging Applications

Recent interest in direct-ranging navigation methods has prompted new research into practical receiver structures which provide improved signal processing. Maximum likelihood receivers are compared with conventional phase-locked receivers by theoretical and simulation methods as phase estimators based on signal measurements only. Signal-to-noise ratio (SNR) enhancement is examined and filter recommendations made. An adaptive maximum likelihood receiver is then developed which uses both signal measurements and a priori data to improve phase estimation accuracy. Simulation results indicate a 33.3 dB processing gain yielding a ranging error standard deviation of ±15 feet for zero dB received SNR. Nonadaptive and adaptive receivers are fabricated, flight tested, and experimental results reported.     

北斗导航接收机频率稳定度传递算法

为了提高北斗导航接收机的灵敏度,提升其弱信号跟踪能力,通常需要利用长时间的相干积分来提高环路信噪比。但是,当相干积分时间加长到一定程度时,环路性能反而有所下降,信噪比提升也不能达到理论值。针对由剩余频率误差和晶振误差引起的相干积分能量损失问题,主要研究了频率偏差对环路跟踪性能的影响,并提出了利用频率稳定度传递策略辅助弱信号跟踪的方法,解决了北斗导航接收机弱信号跟踪性能提升的问题,最大程度地改善了相干积分的效果,实现了对弱信号的跟踪。利用软件接收机平台对提出的频率稳定度传递算法进行验证,仿真结果表明该算法可使环路信噪比提升4dB ~5dB,充分说明了其可行性及有效性。     

Signal-to-Noise Ratio in the Bandpass Output of a Discriminator

A formula is derived for the output signal-to-noise power ratio from a limiter-discriminator that is followed by an ideal (rectangular) bandpass filter. This signal-to-noise ratio is shown to be inversely proportional to the difference between the cube of the upper cutoff frequency and the cube of the lower cutoff frequency. The formula commonly utilized by designers for the discriminator output signal-to-noise ratio was derived for the case of a lowpass filter on the discriminator output. The bandpass and low-pass formulas are compared to indicate 1) the advantage of bandpass filtering for the discriminator output, and 2) the error incurred if the designer employs the low-pass formula to evaluate the performance of a bandpass filter design. Finally, the accuracy of a narrow-band approximation for the bandpass formula is evaluated.     

Interference Effects of Pseudo-Random Frequency-Hopping Signals

When a pseudo-random frequency-hopping signal is intercepted by a conventional receiver operating within the same frequency band, the interfering signal has the form of a pulse-amplitude modulated signal. Each pulse amplitude is dependent upon the hopping frequency and the selectivity characteristic of the victim receiver. The probability density function for the interfering pulse amplitude prior to demodulation is determined when the probability density function for the hopping frequency is uniform and the victim-receiver characteristic is 1) ideal flat bandpass, 2) single tuned, and 3) Gaussian shaped. It is shown that the average interfering pulse amplitude and interference power decrease as the frequency-hopping bandwidth increases with respect to the victim-receiver bandwidth. Fast Fourier transform computer techniques are used to obtain the probability density function of the interference amplitude in a Gaussian receiver when several (from 2 to 10) pseudo-random frequency-hopping systems are simultaneously using the same frequency band. The probability that the interference exceeds a prescribed threshold value is computed from the derived probability density functions. This probability may be used in signal-to-interference ratio calculations, to describe the capture effect, or to compute the expected number of clicks produced in an FM discriminator.     

The Performance of an LMS Adaptive Array with Frequency Hopped Signals

The performance of an LMS adaptive array with a frequency hopped, spread spectrum desired signal and a CW interference signal is examined. It is shown that frequency hopping has several effects on an adaptive array. It causes the array to modulate both the amplitude and the phase of the received signal. Also, it causes the array output SINR (signal-to-interference-plus-noise ratio) to vary with time and thus increases the bit error probability for the received signal. Typical curves of the desired signal modulation and the time-varying SINR at the array output are presented. It is shown how the array performance depends on hopping frequency, frequency jump size, interference frequency, signal arrival angles, and signal powers.     

DME Interference mitigation for L-DACS1 based on system identification and sparse representation

L-band digital aeronautical communication system 1 (L-DACS1) is a promising candi-date data-link for future air-ground communication, but it is severely interfered by the pulse pairs (PPs) generated by distance measure equipment. A novel PP mitigation approach is proposed in this paper. Firstly, a deformed PP detection (DPPD) method that combines a filter bank, correlation detection, and rescanning is proposed to detect the deformed PPs (DPPs) which are caused by mul-tiple filters in the receiver. Secondly, a finite impulse response (FIR) model is used to approximate the overall characteristic of filters, and then the waveform of DPP can be acquired by the original waveform of PP and the FIR model. Finally, sparse representation is used to estimate the position and amplitude of each DPP, and then reconstruct each DPP. The reconstructed DPPs will be sub-tracted from the contaminated signal to mitigate interference. Numerical experiments show that the bit error rate performance of our approach is about 5 dB better than that of recent works and is closer to interference-free environment.