Suitability of pulse train control technique for BIFRED converter

Pulse Train/spl trade/ control scheme is presented and applied to a boost integrated flyback rectifier/energy storage dc-dc (BIFRED) converter operating in discontinuous conduction mode (DCM), which avoids the light-load high-voltage stress problem. In contrast to the conventional control techniques, the principal idea of Pulse Train technique is to regulate the output voltage using a series of high and low energy pulses generated by the current of the inductor. The applicability of the proposed technique to both the input and magnetizing inductances of BIFRED converter is investigated. Analysis of BIFRED converter operating in DCM as well as the output voltage ripple estimation is given. Experimental results on a prototype converter are also presented.     

Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

Improved ZCS-PWM commutation cell for IGBTs application

An improved zero-current-switching pulsewidth-modulated (ZCS-PWM) commutation cell is presented, which is suitable for high-power applications using insulated gate bipolar transistors (IGBTs) as the power switches. It provides ZCS operation for active switches and zero-voltage-switching (ZVS) operation for passive switches. Besides operating at constant frequency and reducing commutation losses, the proposed ZCS-PWM switch cell has no additional current stress and conduction loss in the main switch. To demonstrate the feasibility of the proposed ZCS-PWM commutation cell, it was applied to a boost converter. Operating principle, theoretical analysis, design guidelines, and a design example are described and verified by experiment results obtained from a prototype rated 1 kW and operating at 40 kHz. The PWM switch model and state-space averaging approach is also used to estimate and examine the steady-state and dynamic character of ZCS-PWM boost converter system. Finally, the application of the proposed soft-switching technique in the dc-dc nonisolated converters is presented.     

Alternate forms of the PWM switch models

Vorperian's pulsewidth modulation (PWM) switch model consists of a PWM transformer and a nonlinear resistor. The recognition that any of the three transformer terminals can serve as the common terminal leads to two alternate PWM transformer models and the corresponding two alternate PWM switch models. For a given PWM dc-dc converter, one of the three PWM switch models is more “natural” for graphic-oriented analysis/design, e.g., it allows the idealized converter to be analyzed by inspection. Furthermore, all three PWM transformers may be used to graphically manipulate the converter circuit to a form that can be analyzed by inspection. The alternate forms of the PWM transformers and the PWM switch models are effective as graphic-oriented teaching and learning tools for PWM converters. This is demonstrated using examples based on the boost converter and the Cuk converter     

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Improved multilevel quantization for detection of narrowbandsignals

Nearly optimum quantization levels for multileveled quantizers in radar receivers and distributed-detection are calculated for preassigned false-alarm probability Q₀ by maximizing the detection probability Q_d after replacing both Q ₀ and (1-Q_d) by the saddlepoint approximations. Narrowband signals of random phase and with both fixed and Rayleigh-fading amplitudes in Gaussian noise are treated, and the loss in signal detectability incurred by quantization is estimated     

Nonparametric rank detectors on quantized radar video signals

Uniform randomization of ties is required for defining distribution-free ranks of independent and identically distributed quantized samples. Formulas of rank probabilities are given and applied to radar detection under quantized video samples. For some detectors, and assuming Gaussian noise, the asymptotic loss L_∞(q) is calculated versus the normalized quantization step q, and the loss L(q) is estimated by Monte Carlo simulations. Both of these resulted in monotonic functions of q (0<q<1.1) that are independent of the other parameters. Furthermore, L(q)≈L_∞(q )⩽0.45 dB, as q<0.8. The quantization step q is normalized with respect to the noise standard deviation     

Single-Stage Single-Switch Switched-Capacitor Buck/Buck-Boost-Type Converter

A new dc-dc converter featuring a steep step-down of the input voltage is presented. It answers a typical need for on-board aeronautics modern power architectures: power supplies with a large conversion ratio able to deliver an output voltage of 1–1.2 V. The proposed structure is derived from a switched-capacitor circuit integrated with a buck converter; they share the same active switch. The proposed solution removes the electromagnetic interference (EMI) emission due to the large di/dt in the input current of the switched-capacitor power supplies. Compared with a quadratic buck converter, it presents a similar complexity, a smaller reduction in the line voltage at full load (but less conduction losses due to smaller input inductor current and capacitor voltage), lower voltage stresses on the transistor and diodes, lower current stresses in the diodes, and smaller size inductors. A similar structure using a buck-boost converter as the second stage is also presented. The experimental results confirm the theoretical developments.     

Buck-flyback DC-DC converter

It is difficult to obtain a large input/output voltage ratio with a DC-DC converter, because the duty factor d may not reach very small values. For the same reason, it is difficult to obtain an output voltage that is adjustable in a large range. A DC-DC converter circuit is proposed that overcomes this limitation by performing a voltage ratio d²/(1-d) in the best operating mode. Circuit operation is analyzed, operating modes are evidenced, and the voltage ratio is deduced in each operating mode as a function of output current, duty factor, and circuit component values. Boundary conditions between different operating modes are obtained; consequently, it is concluded that these conditions do not occur for some operating modes. Component ratings are summarized, to facilitate circuit design. The buck-flyback DC-DC converter is very suitable for low-voltage (e.g. computer) power supplies and for power supplies with the output voltage (adjustable in a large range) supplied from the mains without a mains voltage transformer     

Full control of a PWM DC-AC converter for AC voltage regulation

The design and implement action of a DSP-based fully digital-controlled single-phase pulsewidth modulated (PWM) dc-ac converter for ac voltage regulation is described. The proposed multiloop digital controller (MDC) consists of a current controller, a voltage controller, and a feedforward controller. This MDC was realized using a single-chip digital signal processor (DSP). The PWM gating signals are determined at every sampling instant by the proposed multiloop digital control scheme using a set of detected feedback signals. A software current control; scheme has been developed to achieve fast current control of the PWM inverter and decouple the inductor of the output filter. Experimental results have been given to verify the proposed digital control scheme. The constructed DSP-based PWM dc-ac converter system can achieve fast dynamic response and with low total harmonic distortion (THD) for rectifier type of loads     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

Computer Simulations of Optimum Boost and Buck-Boost Converters

The development of mathematical models suitable for minimum weight boost and buck-boost converter designs are presented. The facility of an augumented Lagrangian (ALAG) multiplier-based nonlinear programming technique is demonstrated for minimum weight design optimizations of boost and buck-boost power converters. ALAG-based computer simulation results for those two minimum weight designs are discussed. Certain important features of ALAG are presented in the framework of a comprehensive design example for boost and buck-boost power converter design optimization. The study provides refreshing design insight of power converters and presents such information as weight and loss profiles of various semiconductor components and magnetics as a function of the switching frequency.     

基于TMS320F2812生成移相PWM的2种办法

移相 PWM波是很多开关电源常用的驱动脉冲信号。双向全桥直流变换器(Bidirectional-Full-Bridge DCDC Converter,BDC)在双重移相控制方式下时需要 4组两两互补的移相 PWM波。文章基于 TMS320F2812型 DSP(Digital Signal Processor)分析了 2种生成移相 PWM的方法。为提高双向全桥直流变换器工作的安全性和可靠性,为移相 PWM波设置死区时间。对所提出的方法进行测试后结果良好,对于双向全桥直流变换器闭环控制系统的构建具有重要意义。     

Current Injected Equivalent Circuit Approach to Modeling Switching DC-DC Converters

A new current injected equivalent circuit approach (CIECA) to modeling switching dc-dc converter power stages is developed, which starts with the current injected approach and results in either a set of equations which completely describe input and out-put properties or an equivalent linear circuit model valid at small signal, low frequency levels. This approach to modeling switching dc-dc converter power stages has the merits but not the demerits of both the electronic equivalent circuit state space average approach and the current injected control type approach, namely, 1) the modeling is very clear and is simple whether the converter operates in continuous or discontinuous inductor conduction modes, 2) the modeling results in an equivalent circuit which is very close to the actual converter, and 3) the equivalent circuit can be used directly in the computer for theoretical predictions like SPICE, etc.     

An exact expression for resolution cell area in special case ofbistatic radar systems

An exact expression for the bistatic resolution-cell area (A _B) is developed for the special case in which either the transmit or receive antenna has a broad azimuth beamwidth or is omnidirectional. Quantitative examples are presented to illustrate the variation of A_B with location. A comparison is made with the performance of a commonly used approximation formula     

Multimodule parallel series-loaded resonant converters

The design and implementation of a multimodule parallel series-loaded resonant (SLR) converter system is presented. The SLR converter to be paralleled is operated in the n=2 discontinuous mode (DCM). Its dc analysis and dynamic modeling are made. In parallel operation, an average control technique is proposed to compensate the mismatch in current control characteristics of each parallel converter. Good dynamic and static current sharing characteristics are obtained. In addition, to obtain good output voltage regulating control performance, a design procedure is presented to find the parameters of feedback voltage controller according to the prescribed specifications     

CIECA: Application to Current Programmed Switching Dc-Dc Converters

Sundstrand Advanced Technology Corporation The current injection equivalent circuit approach (CIECA) to modeling switching converter power stages is extended to model the current programmed converter power stages operating in fixed frequency, continuous inductor conduction mode. To demonstrate the method, modeling is carried out for the buck, boost, and buckboost converters to obtain small-signal linear equivalent circuit models which represent both input and output properties. The results of these analyses are presented in the form of linear equivalent circuit models as well as transfer functions. Though current programmed converters exhibit single-pole response, the addition of artificial ramp changes converters to exhibit well damped two-pole response. This has been investigated for the first time using CIECA. The results of these analyses are presented in the form of linear equivalent circuit models as well as transfer functions.     

State-plane analysis of zero-voltage-switching resonant DC/DCconverters

The state-plane analysis technique is established for the zero-voltage-switching resonant DC/DC power converter family of topologies, namely the buck, boost, buck-boost, Cuk, sepic, and dual-sepic converters. The state plane provides a compression of information, which allows the designer to examine the nonlinear dynamics of resonant converter operation. Utilizing the state plane, modes of resonant converter operation are examined. Expressions are derived for the switching frequencies at the boundaries between these modes and at the boundary of energy conversion     

Power tracking for nonlinear PV sources with coupled inductor SEPIC converter

The photovoltaic (PV) generator exhibits a nonlinear i-v characteristic and its maximum power (MP) point varies with solar insolation. In this paper, a V2-based MP point tracking (MPPT) scheme is developed using a buck-boost transformation topology. Although several buck-boost transformation topologies are available we have considered here a coupled inductor SEPIC converter for experimentation. To achieve almost ripple-free array current we have used ripple steering phenomena with the help of integrated inductor. This integrated inductor not only reduces the magnetic core requirements but also improves converter performance. Mathematical models are formulated and tracking algorithm is evolved. A combined PV system simulation model is developed in the SIMULINK. For a given solar insolation, the tracking algorithm changes the duty ratio of the converter such that the solar cell array (SCA) voltage equals the voltage corresponding to the MP point. This is done by the tracking algorithm, which mainly computes the power proportional to square of terminal voltage and changes the duty ratio of the converter so that this power is maximum. The proposed algorithm is implemented in real-time with the help of Analog Device ADMC-401 DSP evaluation module. The tracking program is developed to perform experimental investigations using analog-to-digital converter (ADC) interrupt. Using this processor we are able to track the MP within 200 ms. The proposed peak power tracking effectiveness is demonstrated through simulation and experimental results.     

Simplified analysis of PWM converters using model of PWM switch.Continuous conduction mode

A circuit-oriented approach to the analysis of pulsewidth modulation (PWM) converters is presented. This method relies on the identification of a three-terminal nonlinear device, called the PWM switch, which consists of only the active and passive switches in a PWM converter. Once the invariant properties of the PWM switch are determined, its average equivalent circuit model can be derived. This model is versatile enough to easily account for storage-time modulation of bipolar junction transistor(s) (BJTs); the DC- and small-signal characteristics of a large class of PWM converters can then be contained by a simply replacing the PWM switch with its equivalent circuit model. The methodology is very similar to linear amplifier circuit analysis, whereby the transistor is replaced by its equivalent circuit model