一种高分辨率积分输出的A/D转换电路的设计

针对通常需要高分辨率的模数转换的导航领域,描述了一种高分辨率积分输出的A/D转换电路的设计,论述其工作原理和软硬件设计方案。通过电路仿真和试验分析表明,这种A/D转换电路的设计兼具V/F转换的高精度和A/D转换的高速输出的优点。     

Steady-state analysis of the constant-frequency clamped seriesresonant converter

A constant-frequency diode-clamped series resonant converter (CFCSRC) is proposed as a solution to problems associated with frequency-controlled resonant converters. This converter has two resonant frequencies, and control is achieved by varying the relative time spent at each switching frequency. Two zero-current-switching (ZCS) modes are examined and plotted in the output plane. An equation is given for the boundary between the two ZCS modes, as well as an expression for the boundary between ZCS and non-ZCS operation; both are plotted in the output plane. The output equation for the main mode is shown to be hyperbolic. Converter peak voltages limited to the input voltages, and peak currents are less than those of the frequency-controlled clamped series resonant converter over a large operating range. Data from a prototype converter are compared with theoretical data and are shown to be in good agreement with the theoretical model     

Interleaved boost converter with zero diode reverse-recovery loss

A three-phase interleaved continuous-inductor-current-mode (CICM) boost converter with zero diode reverse-recovery loss is proposed. In the converter, the di/dt of the output rectifiers is controlled by an integrated magnetic component. All the output rectifiers can be turned off softly and a very high efficiency is obtained. The equivalent-circuit model of the integrated inductors, the operation principle of the converter, and the design issues are discussed. Simulation and experimental results are presented.     

Frequency-controlled series-resonant converter with synchronous rectifier

This paper presents an analysis and experimental results for a frequency-controlled series-resonant dc-dc converter that consists of a Class-D zero-voltage-switching (ZVS) series-resonant inverter and a center-tapped synchronous rectifier. If the dc output voltage is low, the efficiency of the converter is dominated by the efficiency of the rectifier. Low on-resistance metal-oxide-semiconductor field-effect transistors (MOSFETs) are used in the rectifier instead of diodes because the forward voltage drop across the rectifying device is low, resulting in a high efficiency. The dc output voltage is regulated against variations in the load resistance and the dc input voltage by varying the operating frequency. Experimental results are presented for a converter with a dc input voltage of 150 V, an output voltage of 5 V, and a dc load resistance ranging from 0.5 to 5.5 R. The measured efficiency was 86% for a 50 W output and 89% for a 25 W output. The theoretical results were in good agreement with the measured results.     

Flyback Converter Output Voltage Stabilization

The expression of the flyback converter output voltage (output power) is derived as a function of the supply voltage, load resistance, transformer ratios, transistor current gain, and base-circuit resistor value. Switching period and duty cycle are also calculated. A converter circuit is designed having stabilized output voltage, with respect to supply voltage, at constant load. The transistor base current is controlled by the supply voltage, via a nonlinear circuit. This feedforward circuit approximates with logarithmic characteristics the ideal hyperbolic dependence of the transistor base current as a function of the supply voltage. The converter has high performance and low cost. A cheaper circuit variant is presented, in which the high-voltage control transistor was eliminated.     

Steady-State Analysis of the Series Resonant Converter

The series resonant converter is analyzed in steady state, and for constant switching frequency the output current and voltage characteristics are found to be ellipses. The converter operating point can then be easily obtained by superimposing a load line on these elliptical characteristics. Peak resonant capacitor voltage and inductor current are also plotted in the output plane and are dependent to first order only on output current. When peak voltage and current are plotted in this manner, the dependence of component stresses on operating point is clearly revealed. The output characteristics are modified to include the effect of transistor and diode voltage drops, and experimental verification is presented.     

串联输出DC／DC谐振变换器的稳态分析

分析了高于谐振频率工作的串联输出谐振变换器的工作模式,采用状态变量法计算获得了若干描述稳态工作的特性曲线,为分析和设计这种变换器提供了基础     

Buck-flyback DC-DC converter

It is difficult to obtain a large input/output voltage ratio with a DC-DC converter, because the duty factor d may not reach very small values. For the same reason, it is difficult to obtain an output voltage that is adjustable in a large range. A DC-DC converter circuit is proposed that overcomes this limitation by performing a voltage ratio d²/(1-d) in the best operating mode. Circuit operation is analyzed, operating modes are evidenced, and the voltage ratio is deduced in each operating mode as a function of output current, duty factor, and circuit component values. Boundary conditions between different operating modes are obtained; consequently, it is concluded that these conditions do not occur for some operating modes. Component ratings are summarized, to facilitate circuit design. The buck-flyback DC-DC converter is very suitable for low-voltage (e.g. computer) power supplies and for power supplies with the output voltage (adjustable in a large range) supplied from the mains without a mains voltage transformer     

Suitability of pulse train control technique for BIFRED converter

Pulse Train/spl trade/ control scheme is presented and applied to a boost integrated flyback rectifier/energy storage dc-dc (BIFRED) converter operating in discontinuous conduction mode (DCM), which avoids the light-load high-voltage stress problem. In contrast to the conventional control techniques, the principal idea of Pulse Train technique is to regulate the output voltage using a series of high and low energy pulses generated by the current of the inductor. The applicability of the proposed technique to both the input and magnetizing inductances of BIFRED converter is investigated. Analysis of BIFRED converter operating in DCM as well as the output voltage ripple estimation is given. Experimental results on a prototype converter are also presented.     

Effects of output filter on cross regulation in SRC

Cross regulation performance of multioutput series resonant converter (SRC) topologies using capacitive or inductive filters is analyzed. The steady state cross regulation characteristics are derived using the state-plane techniques and are illustrated by the examples of two-output SRCs with capacitive and inductive filters. The characteristic curves show that over some range of output currents, the cross regulation performance of an SRC with an inductive filter is much improved over the SRC with capacitance filter and less dependent on the tolerances in leakage inductances and the loading on unregulated outputs. It is shown that the converter control characteristics of an SRC with an inductive filter are relatively unaffected by the addition of the second output. The theoretical results are verified by simulation     

Fault-tolerance wide voltage conversion gain DC/DC converter for more electric aircraft

In this paper, a fault-tolerance wide voltage conversion gain DC/DC converter for More Electric Aircraft (MEA) is proposed. The proposed converter consists of a basic Cuk converter module and n expandable units. By adjusting the operation state of the expandable units, the voltage conversion gain of the proposed converter could be regulated, which makes it available for wide voltage conversion applications. Especially, since mutual redundancy can be realized between the basic Cuk converter module and the expandable units, the converter can continuously work when an unpredictable fault occurs to the fault-tolerant parts of the proposed converter, which reflects the fault tolerance of the converter and significantly improves the reliability of the system. Moreover, the advantages of small input current ripple, automatic current sharing and low voltage stress are also integrated in this converter. The working principle and features of the proposed converter are mainly introduced, and an experimental prototype with 800 W output power has been manufactured to verify the practicability and availability of the proposed converter.     

Current-fed multiresonant isolated DC-DC converter

A novel topology, current-fed multiresonant dc-dc converter (CF-MRC) was studied theoretically and experimentally. The new topology differs from previously described current-fed push-pull parallel-resonant topologies in the fact that the output is coupled to the current of the resonant inductor and in the addition of a second capacitor across the transformer. The main features of the proposed converter are an inherent protection against a short and open circuit at the output, a high voltage gain and zero voltage switching (ZVS) over a large range of output voltage. These characteristics make it a viable choice for applications, such as a high voltage capacitor charger, that require controllable current sourcing over a wide output voltage swing.     

A fixed frequency LCL-Type series resonant converter

A fixed frequency LCL-type series resonant converter (SRC) which uses an inductive output filter is proposed. Steady-state analysis of the converter is presented using complex ac circuit analysis. Based on the analysis, a simple design procedure is given. Detailed space integrated control experiment (SPICE) simulation results are presented to evaluate the performance of the designed converter under varying load and supply voltage conditions. Also, detailed experimental results obtained from a metal-oxide-semiconductor field-effect transistor (MOSFET) based 500 W converter are presented to verify the analysis and SPICE simulation results. The results obtained from the analysis, SPICE simulation and the experimental converter are compared. The proposed converter requires a narrow variation in pulsewidth while maintaining lagging power factor mode of operation for a very wide variation in the load as well as supply voltage     

Novel AC-DC and DC-DC converters with a diode-capacitor multiplier

This paper presents a transformerless ac-dc and or dc-dc converter with a high output voltage multiplicity, which contains only one switch. The converter consists of an inverter and a diode-capacitor multiplier (DCM) and provides a voltage gain equal to double the number of multiplier steps. In the case of ac-dc conversion the proposed converter offers a practically unit power factor and provides a sine wave input current. The analysis of the steady state as well as the transient behavior of the DCM is given and simplified equivalent circuits are proposed. The prototype of the DCM has been built and tested to show the validity of the proposed converter. The theoretical analysis, the computer simulation results, and the experimental testing results are in good agreement.     

Analysis and prediction of regulation in a multiple-outputcurrent-mode controlled DC-to-DC converter

A technique is developed for predicting the closed-loop steady state output voltage regulation of a multiple-output current-mode controlled converter. The proposed model accounts for the current loop, the voltage loop, and the integrator in the compensation scheme. This method allows tradeoffs with respect to regulation between different components or feedback configurations to be evaluated during the design of a converter. Experimental verification on a three-output current-mode controlled push-pull converter with single output voltage feedback is provided     

ZVT boost converter using a ZCS auxiliary circuit

A soft switching boost converter with zero-voltage transition (ZVT) main switch using zero-current switching (ZCS) auxiliary switch is proposed. Operating intervals of the converter are presented and analyzed. Design considerations are discussed. A design example with experimental results obtained from a 600 W, 100 kHz, 380 V output, power factor corrected, ac-to-dc, boost converter using insulated gate bipolar transistors (IGBTs) is presented, Results show that the main switch maintains ZVT while the auxiliary switch retains ZCS for the complete specified line and load conditions     

AC/DC converter topologies for the Space Station

A new class of AC/DC converter topologies (Type-1 converters) is described, suitable for use in an advanced single-phase sine-wave voltage, high-frequency power distribution system, of the type that was proposed for a 20 kHz Space Station primary electrical power distribution system. The converter comprises a transformer, a resonant network, a current controller, a diode rectifier, and an output filter. The input AC voltage source is converted into a sinusoidal current source using the resonant network. The output of this current source is rectified by the diode rectifier and is controlled by the current controller. The controlled rectified current is then filtered by the output filter to obtain a constant voltage across the load. Three distinct converter topologies, Type-1A, Type-1B, and Type 1-C, are described, and their performance characteristics are presented. All three types have a close-to-unity rated power factor (greater than 0.98), low total harmonic distortion in input current (less than 5%), and high conversion efficiency (greater than 96%)     

Efficient power supply for the microwave electrothermal thruster(MET)

A resonant switch-mode power supply for the microwave electrothermal thruster (MET) is presented in this paper. The converter is operated with soft-switching at high frequency and exhibits a high efficiency. The soft switching technique used in this converter and the current-source inductor at the input minimize the EMI noise. Electric isolation between input and output is achieved with a center-tap transformer, whose magnetizing inductance is used as the resonant inductance of its resonant tank. The resulting high power density and increased reliability of the converter make it very suitable for aerospace applications. Simulation and experimental results of a 28 V/4.5 kV example are also presented     

Fourier theory of jumps applied to converter harmonic analysis

The Fourier theory of jumps (FTJ) is demonstrated as an aid in deriving closed-form analytical equations for converter switching harmonics. The switching waveforms analyzed are the input current and output voltage and current of a three-phase, ac-dc, step-down, dead-band pulsewidth modulated (PWM), unity power factor converter. The input current closed-form harmonic equation is derived for two parallel-connected, interleaved-PWM converters supplying the same load and sharing a common input filter. The equations are compared with PSpice^TM simulations and practical results     

A novel resonant converter topology for DC-to-DC power supply

A class-E DC-to-DC converter with half-wave controlled current rectifier is proposed. Its output voltage is controlled by the conduction angle of the rectifier switch at constant switching frequency. Zero voltage switching for all the switches can be maintained from full load to no load. Its steady state characteristics are analyzed and the effects of the circuit parameters are studied. Some extensions of the proposed converter are also discussed. The analysis is verified by PSPICE simulation and an experimental prototype