共查询到20条相似文献,搜索用时 438 毫秒
1.
2.
3.
研究了一种适用于焊接铝合金的超快速变换复合脉冲方波变极性电弧焊接工艺,以5A06铝合金为焊接试验对象,对不同工艺参数下复合脉冲方波变极性TIG焊接接头的显微组织和拉伸力学性能变化进行了试验研究.结果表明,在5A06铝合金焊接过程中引入高频直流脉冲方波电流,恰当选择其频率和占空比大小,可增加焊缝组织中金属间化合物的析出数量,显著改善和提高5A06铝合金的焊接质量.当脉冲电流频率为40 kHz,占空比为50%时,焊接接头拉伸强度和断后伸长率分别达到母材金属的95.8%和84.8%. 相似文献
4.
5.
针对生产现场大尺寸5A06-H112铝合金板箱形件拼焊制造过程中存在应力松弛的问题,对多种焊接工艺方法进行了研究.通过对不同焊接接头的力学性能试验、残余应力测试、焊接金相和硬度测量结果对比显示,铝合金焊接结构的应力变化存在先升后降的变化趋势,而TIG焊由于采用较小的线能量和多层焊,较MIG焊其应力松弛的程度存在差异.结果表明,增加焊后时效时间8~10d,并采用TIG焊技术将有效减小铝合金焊接结构的应力松弛,使端头下沉减少50%左右,满足了设计图纸的要求. 相似文献
6.
针对2A14、2219、2195、2A97、1460铝合金,通过焊接热模拟试验、焊接裂纹敏感性试验和拉伸试验,建立了材料脆性温度区间大小和焊接性的关系及焊丝主成分和焊接性的关系。结果表明,试验合金焊接性从好到差的排列顺序为2219、2A14、1460、2195、2A97。其中2A14、2219铝合金现用焊丝可以满足推进剂贮箱用铝合金焊接性要求。脆性温度区间较小时,焊接性良好,随脆性温度区间增加,焊接性变差;采用满足主成分含量之和为6%的焊丝焊接时,若抗裂性满足要求,则接头延伸率满足要求。 相似文献
7.
焊接方法对2219铝合金性能及组织的影响 总被引:4,自引:0,他引:4
通过拉伸试验,利用扫描电镜与光学显微镜等手段,比较了搅拌摩擦焊(FSW)和变极性钨极氩弧焊(VPTIG)两种焊接方法对2219铝合金板材力学性能的影响.结果表明,无论何种焊接方法均使2219铝合金板材的强度和塑性下降,但是FSW焊接接头强度以及塑性等力学性能明显优于VPTIG焊熔焊接头.拉伸试样断口形貌以及显微组织分析显示,FSW焊核区组织均匀细密,断裂位置位于后退侧热影响区与焊核区的交界处.VPTIG焊接接头易出现气孔缺陷,熔合区是最薄弱环节. 相似文献
8.
9.
为保证航空航天器中贮存腐蚀溶液的焊接结构的耐久性,有必要对焊接接头预腐蚀强度特性进行研究.首先进行2219-T87铝合金焊接接头试样在酸性模拟溶液中的腐蚀试验,获取焊接接头和母材的腐蚀性能数据;根据腐蚀试验数据,结合焊接接头局部力学试验数据,采用有限元方法对焊接接头预腐蚀强度和断裂位置进行预测;通过焊接接头预腐蚀拉伸试验对预测结果进行验证.研究结果表明:焊接接头腐蚀性能最主要的特点是焊缝区、热影响区和母材的腐蚀性能存在显著差异;腐蚀性能是影响焊接接头预腐蚀强度的重要因素,且其影响随着腐蚀时间的增加而逐渐增大,导致长时间腐蚀的试样在拉伸试验中的断裂位置由力学性能薄弱的熔合区转移到腐蚀性能薄弱的母材区;所提出的预测方法具有试验规模小、结果准确且适应性强的优点. 相似文献
10.
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:2,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
13.
Integrated Entry Guidance for Reusable Launch Vehicle 总被引:2,自引:2,他引:0
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
14.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
15.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
16.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
17.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
18.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
19.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献