Fiber-optic radar calibration

A simple fiber-optic radar calibration target is described. Its operation is based on a wideband fiber, a laser transmitter that is directly modulated by the down-converted radar signal and an optical diode receiver recovering said signal. Further up-conversion having a common local oscillator with the first mixer ensures fidelity of the calibration return. Measured useful bandwidth exceeds 200 MHz and practically any radar RF frequency can be handled when suitable mixers are employed. Amplifiers can be added to the down-converted path as desired to compensate for the fiber loss. Modulation and LO sweep provide easy ways of introducing artificial fluctuations and Doppler frequencies. Particularly pulsed radars are readily tested with the proposed scheme as no restrictions are posed by the radar's TR-switch delays.     

Rotating Blades Radio Interference in a Helicopter-Borne CW Doppler Radar

Radio interference generated in a helicopter-borne continuous wave (CW) Doppler radar system due to the rotating blades is analyzed. This problem has been previously treated for the case of pulse Doppler radar systems with very narrow (near zero) beamwidth. In this case the strong interference component returning directly from the blades (with no ground reflection) need not be considered as it reaches the receiver when it is still blinded. In the case of a CW Doppler radar, however, this interference component must be included. Numerical calculations show that the total blade interference power level, dominated by the direct component, is higher than that of the direct ground clutter in the radar clutter region. It decreases approximately as (f - fo)-4 in the radar clear region. It stays, however, well above the thermal noise level which might cause false alarm and degrade the radar performance.     

基于3DT的空时自适应单脉冲参数估计算法

空时自适应处理(STAP)是机载预警雷达抑制杂波和干扰的一项关键技术,而多普勒三通道联合自适应处理(3DT)是适合工程实现的降维(RD)STAP方法。STAP目标检测后还需进一步估计目标的角度参数,因此将自适应单脉冲(AM)技术引入3DT,提出了一种高精度联合估计目标速度与方位空间角的空时自适应单脉冲算法。理论分析与仿真实验结果表明,当目标多普勒频率偏离检测多普勒单元中心频率时,该算法能同时减少目标多普勒跨越损失和空时导引矢量失配损失,进而提高输出信杂噪比(SCNR),改善目标测角精度。     

Group-Complementary Array Coding for Radar Clutter Rejection

A radar waveform design technique which utilizes Lagrange's method of multipliers to control temporal sidelobes and to reduce Doppler sidelobes is described. This classical method of constrained optimization is applied to the problem of synthesizing a radar wave-form where mismatch loss is the objective function to be minimized. The associated constraints are taken from expressions for the composite temporal sidelobes of the cross-correlation response and the peak correlation response where sets of code words are used to modulate a series of radar pulses. The resulting code sets and receiver reference sets are called group-complementary and produce a trench parallel to or on the range axis of the cross-ambiguity surface.     

GLRT Detectors for Aircraft Wake Vortices in Clear Air

 In this article, radar echoes of aircraft wake vortices are modeled as weighted sums of the frequency components of the echoes with a special covariance matrix for the weighted coefficients. With a proposed detection scheme, two generalized likelihood ratio test (GLRT) detectors are derived respectively for aircraft wake vortices with time-varying and time-invariant Doppler spectra. Then the analytical expressions for detection and false alarm probabilities of the detectors are derived and three factors are investigated which mainly influence the detection performance, i.e., the Doppler extension and uncertainty of the aircraft wake vortex, and the number of the detection cells. The results indicate that, the signal-to-noise ratio (SNR) loss induced by Doppler extension is generally several decibels. The SNR loss due to Doppler uncertainty is approximately proportional to the logarithm of the number of spectrum lines in the uncertain Doppler spectrum intervals. For a large number of detection cells, the SNR gain is approximately proportional to the square root of the number of the detection cells.     

A Distribution-Free Doppler Processor

A distribution-free Doppler processor (DFDP) is described. This procedure is applicable to the detection of signals with unknown phase or signals which undergo a change in phase from one observation to the next. The procedure has the characteristic that the false-alarm probability is a constant, independent of the probability distribution of the received data when no signal is present. Also, an estimate of the Doppler frequency, when applied to a Doppler radar processor, is provided.     

应答机对称天线干涉对雷达信号影响分析

针对测速雷达在目标旋转时,由对称天线导致的下行信号干涉问题,通过理论分析远场条件下信号干涉合成方向图变化情况和双基微多普勒计算方法,提出了一种分析干涉区前后多普勒阶跃的方法。通过分析测速雷达记录数据中AGC(Automatic Gain Control,自动增益控制)电平、多普勒和综合误差电压,再利用小波变换和自相关方法,可以提取微多普勒信息和微多普勒周期。理论分析和数据验证可知,信号干涉区出现在对称天线中间±20°左右,雷达接收AGC电平在干涉区下降10~20dB,多普勒差分出现峰值,微多普勒在干涉区前后出现正负峰值,综合误差电压会显著增大。这些结论有利于认识干涉现象对测速设备接收信号的影响。     

Properties of Staggered PRF Radar Spectral Components

Expressions for moving target indicator (MTI) improvement factor limitation due to pulse repetition frequency (PRF) staggering and loss of target detectability for various values of Doppler frequency in the passband are presented. It is also shown that the product of variance of stagger periods and clutter variance is an important parameter determining the performance of a staggered PRF MTI radar.     

Moving target detection via airborne HRR phased array radar

We study moving target detection in the presence of temporally and spatially correlated ground clutter for airborne high range resolution (HRR) phased array radar. We divide the HRR range profiles into large range segments to avoid the range migration problems that occur in the HRR radar data. Since each range segment contains a sequence of HRR range bins, no information is lost due to the division and hence no loss of resolution occurs. We show how to use a vector autoregressive (VAR) filtering technique to suppress the ground clutter. Then a moving target detector based on a generalized likelihood ratio test (GLRT) detection strategy is derived. The detection threshold is determined according to the desired false alarm rate, which is made possible via an asymptotic statistical analysis. After the target Doppler frequency and spatial signature vectors are estimated from the VAR-filtered data as if a target were present, a simple detection variable is computed and compared with the detection threshold to render a decision on the presence of a target. Numerical results are provided to demonstrate the performance of the proposed moving target detection algorithm     

Mm wavelengths complex Doppler analysis using dark field illumination

Experimental results that indicate that at least two fundamental modes of Doppler generation are present when a rotating steel cylinder is broadside illuminated by radar. Improvised bistatic measurements at 77GHz are discussed and second order Doppler effects studied. Complex Doppler returns, consisting of two or more Doppler contributions, are decomposed and studied using empirical methods. In particular, ground illumination techniques are used to study Doppler in the shadow region of a cylinder of circumference 81 wavelengths. It is concluded that the complex Doppler response from the spinning cylinder consists of both direct (first order) and delayed (second order) Doppler components. Further measurements are proposed to study the delayed Doppler effect further.     

机载脉冲多普勒雷达DBS技术

 本文从多普勒谱分辨理论出发,分析了DBS成象的基本原理,实现DBS成象的实时信号处理过程,提出了DBS实时数字信号处理方案。通过计算机模拟试验表明,在雷达天线保持匀速扫描状态时,系统的多普勒波束锐化比可达17.4:1左右,并可对载机前方±15°—60°方位范围内提供一幅大面积的,高分辨力的扇形雷达图象。     

Measurements of L-band inland-water surface-clutter Doppler spectra

Although radar surface-clutter reflectivities from terrain are generally much greater than those from water, strong Bragg resonances at low but non-zero Doppler frequencies in backscatter from small inland bodies of water might potentially cause false alarms for moving target indicator (MTI) or other Doppler signal-processing techniques designed for target detection in ground clutter. To provide data for investigating this concern, measurements of L-band radar backscatter were recorded from the surface of a small inland freshwater reservoir in central Massachusetts. These measurements were of unusually high system stability and spectral purity so as to provide up to 80 dB of available spectral dynamic range. Strong Bragg spikes occurred in the clutter Doppler spectra from the reservoir at low (3 to 4 Hz) but non-zero Doppler frequencies. This strong Bragg resonance was persistent in time and space throughout the measurements. Spectral results are presented for all four combinations of linear polarization. Comparison with tree clutter spectral results indicates that, when an occasional water body comes under surveillance at vertical polarization in otherwise generally forested terrain, water clutter spectral density is expected to exceed surrounding-terrain tree clutter spectral densities in the Bragg-offset Doppler vicinity by large amounts     

Doppler Processor Rejection of Range Ambiguous Clutter

Doppler processors are used in radar to separate target returns from clutter. When the clutter is at a range farther than the unambiguous range of the radar, the ability to reject the clutter is degraded. In this article the degradation is analyzed for an N-pulse batch processor with Dolph weighting, and the results show how degradation varies with design sidelobe level.     

基于Keystone变换和MDCFT的高机动弱目标检测与参数估计

 常规雷达对隐身、超声速和高机动目标存在回波信噪比不足、距离徙动和多普勒谱扩展问题。将Keystone变换和修正离散Chirp-Fourier变换(MDCFT)相结合,提出了一种新的雷达信号处理算法。该算法通过Keystone变换补偿距离徙动问题,利用MDCFT对多普勒谱严重扩展的目标回波进行相参积累,提高目标检测性能的同时完成了对目标参数的估计,且该算法在方位向欠采样时仍可适用。最后对算法运算量及性能进行了分析,通过仿真验证了该算法的有效性。     

Spectrum Distortion Due to Frequency Instabilities in a Two-Way Coherent Doppler Radar

The power spectral density of the intermediate frequency signal in a coherent Doppler navigation radar is derived. The effects of antenna parameters, periodic frequency instabilities, signal two-way transit time, and transmitter frequency modulation noise are considered Several examples based on the measured frequency modulation noise of a solid-state source transmitter are presented. The results indicate the degree of loss in signal-to-noise ratio, and spectrum broadening due to an increase in signal transit time and/or frequency modulation noise.     

Principle and Design of a Vernier FM Radar System

This paper describes the principle and the signal design of a proposed new FM radar system. In order to measure the surface characteristics of a small target at a long distance, or to discriminate among multiple targets, very accurate range or Doppler resolutions are necessary [1]. The proposed system satisfies the range resolution requirement by detecting the target with two different resolutions: coarse resolution for measuring range, and fine resolution for measuring the target details. The principal advantage of the system is in the vernier scale for the measurement of a distance. The system is just as easily realizable as conventional FM radar, requires no special filters in the receiver, and represents a saving in the required bandwidth for the same range resolution.     

Signal processing of wide bandwidth and wide beamwidth P-3 SAR data

This research is concerned with multidimensional signal processing and image formation with FOliage PENetrating (FOPEN) airborne radar data which were collected by a Navy P-3 ultra wideband (UWB) radar in 1995. The digital signal processors that were developed for the P-3 data commonly used a radar beamwidth angle that was limited to 35 deg. Provided that the P-3 radar beamwidth angle (after slow-time FIR filtering and 6:1 decimation) was 35 deg, the P-3 signal aperture radar (SAR) system would approximately yield alias-free data in the slow-time Doppler domain. We provide an analysis here of the slow-time Doppler properties of the P-3 SAR system. This study indicates that the P-3 database possesses a 50 deg beamwidth angle within the entire [215, 730] MHz band of the P-3 radar. We show that the 50-degree beamwidth limit is imposed by the radar (radial) range swath gate; a larger beamwidth measurements would be possible with a larger range swath gate. The 50-degree beamwidth of the P-3 system results in slow-time Doppler aliasing within the frequency band of [444, 730] MHz. We outline a slow-time processing of the P-3 data to minimize the Doppler aliasing. The images which are formed via this method are shown to be superior in quality to the images which are formed via the conventional P-3 processor. In the presentation, we also introduce a method for converting the P-3 deramped (range-compressed) data into its alias-free baseband echoed data; the utility of this conversion for suppressing radio frequency interference signals is shown     

Doppler Radar Error Equations for Damped Inertial Navigation System Analysis

The use of Doppler radar measurements to provide velocity damping for an aircraft inertial navigation system is considered. Three different Doppler antenna configurations are examined: two-axis stabilized, azimuth stabilized, and data stabilized antennas. A general reference velocity error equation is presented and appropriately evaluated for each of the Doppler configurations. Specific elements of the error equations are examined and physically interpreted for both local-level and space-stable inertial systems. Detailed examination of the interaction of Doppler radar and inertial navigation velocity error mechanisms is provided.     

Some Results on Pulse-Burst Radar Design

Pulse-burst radar attempts to capitalize on the advantages of both low and high PRF radar while minimizing their disadvantages. Optimization procedures are applied to the choice of transmitter signal and receiver weighting. The results are compared to the use of Tschebyscheff transmitter weighting with an optimized receiver. The effects of various design and operational parameters are indicated. The performance of pulse-burst radar is qualitatively compared to that of conventional low and high PRF Doppler radar. It is concluded that pulse-burst radar offers the possibility of achieving a solution to the MTI problem under operational conditions where conventional Doppler radars fail.     

A novel range-Doppler imaging algorithm with OFDM radar

Traditional pulse Doppler radar estimates the Doppler frequency by taking advantage of Doppler modulation over different pulses and usually it requires a few pulses to estimate the Doppler frequency. In this paper, a novel range-Doppler imaging algorithm based on single pulse with orthogonal frequency division multiplexing(OFDM) radar is proposed, where the OFDM pulse is composed of phase coded symbols. The Doppler frequency is estimated using one single pulse by utilizing Doppler modulation over different symbols, which remarkably increases the data update rate. Besides, it is shown that the range and Doppler estimations are completely independent and the well-known range-Doppler coupling effect does not exist. The effects of target movement on the performances of the proposed algorithm are also discussed and the results show that the algorithm is not sensitive to velocity. Performances of the proposed algorithm as well as comparisons with other range-Doppler algorithms are demonstrated via simulation experiments.