基于机载单天线雷达一维距离数据的地表三维信息优化重建方法

陆地的刚体表面在机载雷达的任意相对运动下具有几何不变性,基于此约束可利用雷达距离像中提取出的地面多个强散射点的一维距离数据,重建出地表的三维信息以及载机未知的运动轨迹.鉴于现有基于雷达远场假设的重建方法无法适用于具有较大近场误差的地面目标重建的问题,提出一种基于雷达近场几何模型的优化重建方法,采用非线性优化方法实现了对...     

High resolution reconstruction of ISAR images

A 2-D high-resolution spectral analysis algorithm with application to an inverse synthetic aperture radar (ISAR) imaging, is presented. This algorithm is based on two-dimensional linear prediction using autoregressive (AR) coefficients. Stability is guaranteed by AR process pole adjustment. An ISAR target is modeled for a complex scatterer geometry. Computer simulation results are provided for the high-resolution reconstruction of ISAR images     

ISAR imaging of targets at low elevation angles

The problem of inverse synthetic aperture radar (ISAR) image reconstruction of targets at low elevation angle is considered. In this geometric condition the main causes affecting the reconstructed ISAR image are the multipath effect due to the reflection of the Earth's surface and the angular motions of the target produced by external action like wind, fast maneuvering, and sea waves as in the case of ships. The aim of this work is to analyze the effects that the multipath and the target angular motions jointly produce on the ISAR image. The results show that multipath generates some artifacts in the image whereas the target oscillations undergo a spatial-dependent blurring of the point spread function of the ISAR system. These theoretical results are validated by presenting some numerical examples relevant to aircrafts and ships in rectilinear or circular motion. A wide discussion on possible solutions of this problem is made in the conclusion     

Radar sensor using low probability of interception SS-FH signals

One of the best known weakness of radar sensors in defense and security applications is the necessity to radiate a signal, which can be detected by the target, so being possible (easy in fact) that the target is alerted about the presence of a radar before the radar is alerted about the presence of a target. In this context, Low Probability of Interception (LPI) Radars try to use signals that are difficult to intercept and/or identify. Spread spectrum signals are strong candidates for this application, and systems using special frequency or polyphase modulation schemes are being exploited. Frequency hopping, however, has not received much attention. The typical LPI radar at this moment of the technology is a CW-LFM radar. The simplicity of the technology is its best point. Polyphase codes, on the other hand have the inherent advantage of high instantaneous bandwidth regardless of observation time. But the complexity of the hardware is also higher. FH signals have traditionally been considered of lower performance but higher complexity, due to the difficulties to compensate the individual dopplers for the individual range cells in the receiver. One important point is that an FH radar must be clearly distinguished from an agile frequency radar. In the latter, a pulsed signal is transmitted using different frequencies from pulse to pulse. In an FH radar the frequency changes must be during the pulse. In fact, in an LPI FH radar, a CW frequency hopped signal is used. A radar system concept is proposed in which it shows how these problems can be overcome in a tracking application. Also, the signal format is analyzed under the scope of future decade digital interceptors, showing that, in fact, this kind of signal exhibits improvement in some performances and requires a hardware that is only slightly more complex than that needed for CW-LFM systems     

Pade approximations for detectability in K-clutter and noise

The Pade approximation (PA) method is used to analyze the detection performance of single and multiple pulse radar systems operating in K-distributed clutter and thermal noise. Simple approximations for false-alarm and detection probabilities are obtained, using lower order moments for the detection decision statistic. Both envelope and squaring detector laws are considered, with noncoherent integration, for independent and correlated K clutter. The target is assumed to be pulse-to-pulse Rayleigh fading. The methods are a substantial application of the PA methods we have previously published     

Precision tracking algorithms for ISAR imaging

The simultaneous imaging and tracking of a moving target is one of the most difficult problems in inverse synthetic aperture radar (ISAR) signal processing. The problem is addressed here using a two-antenna imaging radar. The target range shift is sensed with an exponentially averaged envelope correlation algorithm while the angle change is measured with a differential phase shift algorithm. The three state Kalman filters are used in range and azimuth dimensions to provide both a filtered estimate and a one-sample-ahead prediction for the purpose of target tracking. The filtered range shift provides an accurate information for range bin alignment, and the target angle change provides the angular positions of the synthetic array elements. Therefore, the ISAR imaging simply becomes processing of a circular-arc aperture. The algorithms are verified both by computer simulations and also with experimental data processing     

Radar target identification using the bispectrum: a comparativestudy

Radar target identification is performed using time-domain bispectral features. The classification performance is compared with the performance of other classifiers that use either the impulse response or frequency domain response of the unknown target. The classification algorithms developed here are based on the spectral or the bispectral energy of the received backscatter signal. Classification results are obtained using simulated radar returns derived from measured scattering data from real radar targets. The performance of classifiers in the presence of additive Gaussian (colored or white), exponential noise, and Weibull noise are considered, along with cases where the azimuth position of the target is unknown. Finally, the effect on classification performance of responses horn extraneous point scatterers is investigated     

Iterative MMSE method and recurrent Kalman procedure for ISAR imagereconstruction

This work presents a novel approximate iterative and recurrent approach for image reconstruction from inverse synthetic aperture radar (ISAR) data. Mathematical models of the quadrature components of the ISAR signal, reflected by an object with a complex geometry, are devised. Approximation matrix functions are used to describe deterministic signals reflected by point scatterers located at nodes of the uniform grid (model) during inverse aperture synthesis. Minimum mean square error (MMSE) equations and Kalman equations are derived. To prove the validity and correctness of the developed iterative MMSE method and recurrent Kalman procedure, numerical experiments were performed. The computational results demonstrate high resolution images, unambiguous and convergent estimates of the point scatterers' intensities of a target from simulated ISAR data     

雷达低空目标俯仰角跟踪的C2算法研究

在单脉冲测角体制下,由于多径回波信号的干扰,极大地降低了雷达低空目标仰俯角跟踪精度,甚至丢失目标。通过对多路径反射环境模型分析,得出了岸、海基单脉冲雷达低空目标跟踪时仰俯角测量误差的产生原因,提出将传统的多目标分辨算法(C2算法)应用于低角多径环境下目标俯仰角的跟踪测量,并在不同多径反射环境下对不同高度、不同飞行速度和飞行方向的目标进行了仿真,得到良好的仿真结果,表明该算法可较大地提高俯仰角跟踪测量精度。通过对仿真结果的分析,验证了该算法在低空目标跟踪中的有效性和可行性。     

Receiver operating characteristics for the coherent UWB randomnoise radar

An ultrawideband (UWB) random-noise radar operating in the 1-2 GHz frequency band has been developed and held-tested at a 200 m range at the University of Nebraska. A unique heterodyne correlation technique based on a delayed transmitted waveform using a photonic delay line has been used to inject coherence within this system. The performance of this radar, assuming a point target, has been investigated from a statistical point of view by developing the theoretical basis for the system's receiver operating characteristics (ROC). Explicit analytical expressions for the joint probability density function (pdf) of the in-phase (I) and quadrature (Q) components of the receiver output have been derived under the assumption that the input signals are partially correlated Gaussian processes. The pdf and the complementary cumulative distribution function (cdf) for the envelope of the receiver output are also derived. These expressions are used to relate the probability of detection (P_d) to the probability of false alarm (P_f ) for different numbers of integrated samples, and the results are analyzed     

Synthetic Aperture Radar

The general theory of side-looking synthetic aperture radar systems is developed. A simple circuit-theory model is developed; the geometry of the system determines the nature of the prefilter and the receiver (or processor) is the postfilter. The complex distributed reflectivity density appears as the input, and receiver noise is first considered as the interference which limits performance. Analysis and optimization are carried out for three performance criteria (resolution, signal-to-noise ratio, and least squares estimation of the target field). The optimum synthetic aperture length is derived in terms of the noise level and average transmitted power. Range-Doppler ambiguity limitations and optical processing are discussed briefly. The synthetic aperture concept for rotating target fields is described. It is observed that, for a physical aperture, a side-looking radar, and a rotating target field, the azimuth resolution is ?/? where ? is the change in aspect angle over which the target field is viewed, The effects of phase errors on azimuth resolution are derived in terms of the power density spectrum of the derivative of the phase errors and the performance in the absence of phase errors.     

基于高度分集的两波束米波雷达测高方法及其应用

米波雷达的波束较宽、由于地面反射引起波瓣分裂,通常只能估高而不能用来测高.针对这一难题本文提出一种基于高度分集的两波束米波雷达测高方法.该方法采用高度不同的两个天线,利用波瓣分裂情况及相互相位关系来测量目标高度.文章分析了此方法测高的精度及影响精度的一些因素.本测高方法已应用于某型雷达信号处理机中,并取得良好效果.     

Radar Partial Coherence Theory: An Introduction

The nature of physical phenomena is such that scattering from portions of an object, a number of objects, or clutter, is not completely unrelated; the underlying environment causes some degree of order in the phenomenon. Radar partial coherence theory describes a structure for the general target, or clutter, and its relationship to radar cross section, waveform coding, and the radar output signal. The clutter ambiguity function is introduced for extended bodies and embraces the (Woodward) ambiguity function for a point target. Due to nonlinear effects caused by partial coherence within the general target, radar signals and targets are formulated in terms of mutual coherence functions. The basic quantities describing the radar output are 1) the radar mutual coherence function (formulated in terms of the radar waveform) and 2) the target mutual coherence function which depends upon target properties, physical environment, and viewing aspect. Random noise (independent point scatterers) and partially coherent portions of reflecting bodies are made accountable in the theory. Partial coherence effects are treated as patches of reflected energy: self-coherent energy patches plus mutually coherent energy among the patches.     

Detection of Target Multiplicity Using Monopulse Quadrature Angle

The feasibility of using the indicated quadrature angle of arrival of a monopulse radar to discriminate a single target from multiple targets, separated in angle within a radar resolution cell, is investigated. The analysis is performed for steady (fixed) and Rayleigh fluctuating targets which cover a broad range of target characteristics. In both cases, the interfering signals due to noise and clutter in the sum and difference monopulse channels are assumed to be independent, zero-mean Gaussian processes. Detection and false alarm probabilities are evaluated analytically and the receiver operating characteristics are obtained for both fixed and fluctuating target cases. It is shown that multiple targets can be discriminated from a single target condition by integrating the indicated monopulse quadrature angle of arrival from several independent pulses. It is also shown that the probability of detecting multiple targets increases as the fluctuation in the target radar cross section decreases, approaching the fixed amplitude case in the limit.     

Hardware-in-the-loop simulation technology of wide-band radar targets based on scattering center model

Hardware-in-the-loop(HWIL) simulation technology can verify and evaluate the radar by simulating the radio frequency environment in an anechoic chamber. The HWIL simulation technology of wide-band radar targets can accurately generate wide-band radar target echo which stands for the radar target scattering characteristics and pulse modulation of radar transmitting signal. This paper analyzes the wide-band radar target scattering properties first. Since the responses of target are composed of many separate scattering centers, the target scattering characteristic is restructured by scattering centers model. Based on the scattering centers model of wide-band radar target, the wide-band radar target echo modeling and the simulation method are discussed. The wide-band radar target echo is reconstructed in real-time by convoluting the transmitting signal to the target scattering parameters. Using the digital radio frequency memory(DRFM) system,the HWIL simulation of wide-band radar target echo with high accuracy can be actualized. A typical wide-band radar target simulation is taken to demonstrate the preferable simulation effect of the reconstruction method of wide-band radar target echo. Finally, the radar target time-domain echo and high-resolution range profile(HRRP) are given. The results show that the HWIL simulation gives a high-resolution range distribution of wide-band radar target scattering centers.     

表面粗糙的复杂目标全极化ISAR图像快速仿真

为了获取基于模板图像的车辆、飞机等复杂目标识别所需的海量高质量逆合成孔径雷达(ISAR)图像,提出了表面粗糙的复杂目标全极化ISAR图像快速仿真方法。该方法预先对车辆和飞机等复杂目标表面粗糙程度进行分级定量描述,并以改进的射线弹跳法和等效边缘流法快速预估来自目标粗糙表面的镜面反射和多次反射贡献以及细分边缘的绕射贡献,经相干叠加获得目标的精确电磁散射数据,最后进行成像处理得到高质量全极化ISAR图像。标准体、飞机和车辆目标的仿真实验结果验证了该方法的准确性和有效性。     

Separation of target rigid body and micro-doppler effects in ISAR imaging

Micro-Doppler (m-D) effect is caused by moving parts of the radar target. It can cover rigid parts of a target and degrade the inverse synthetic aperture radar (ISAR) image. Separation of the patterns caused by stationary parts of the target from those caused by moving (rotating or vibrating) parts is the topic of this paper. Two techniques for separation of the rigid part from the rotating parts have been proposed. The first technique is based on time-frequency (TF) representation with sliding window and order statistics techniques. The first step in this technique is recognition of rigid parts in the range/cross-range plane. In the second step, reviewed TF representation and order statistics setup are employed to obtain signals caused by moving parts. The second technique can be applied in the case of very emphatic m-D effect. In the first step the rotating parts are recognized, based on the inverse Radon transform (RT). After masking these patterns, a radar image with the rigid body reflection can be obtained. The proposed methods are illustrated by examples     

Nonuniform Three-dimensional Configuration Distributed SAR Signal Reconstruction Clutter Suppression

This paper deals with the problem of clutter suppression in spaceborne distributed synthetic aperture radar (D-SAR) with nonuniform three-dimensional (3D) configuration geometry. In order to make a breakthrough of the configuration limitation of the traditional space time adaptive processing (STAP) based on uniform array and improve the inhomogeneous clutter suppression performance, this paper considers signal reconstruction technique using array interpolation to process the D-SAR signal. An array interpolation signal reconstruction method based on pitching-partition is derived then a signal reconstruction 3D-STAP clutter suppression method applied to nonuniform 3D configuration is proposed. In particular, the proposed method is compared with conventional methods and the performance analysis is carried out based on simulations. The improvement factor (IF) for clutter suppression is imported and reported as a benchmark on the clutter suppression effect.     

Frequency Agility Radar Range Calculation Using Number of Independent Pulses

A method for accurately calculating the radar range improvement introduced by frequency agility is presented. This calculation is made by using the concept of independent pulses. The number of independent target or clutter pulses is calculated by a simple method based on such basic combinatorial probability theory as drawing differently colored balls from an urn.     

Moving target imaging and trajectory computation using ISAR

Novel algorithms for moving target imaging and trajectory computation using a two-receiver radar are presented. The range-bin alignment is implemented with an adaptive method using the envelope correlation feature of different returns and the angular trajectory equation is solved using a linear least squares method combined with a unique phase-unwrapping technique. The angular positions of the synthetic array elements are determined from the trajectory computation. Three target models moving along a perturbed straight line are used to verify the proposed algorithms