Simulation of <Emphasis Type="Italic">Z</Emphasis>-crimp shaping with the use of the ansys finite element software

A finite element model of the Z-crimp shaping from a hard sheet blank is developed and a number of calculations using the ANSYS finite element software is conducted. The calculations are carried out in the framework of elastoplastic behavior of the blank material using the classical model of bilinear kinematic (translational) hardening with corresponding parameters of elasticity and plasticity. The model takes into account kinematics of spatial transformation of the shaping equipment as well as the time-variable conditions of its contact interaction with the blank.     

Fuel cells for “personal electricity”

Cars powered by fuel cells have been built and tested; however, the aerospace fuel cells could not deliver high power quickly when the driver wanted to accelerate his car. Today's hybrid electric cars carry a battery that supplies the acceleration power, and the prime power source, whether an engine or fuel cell, is not stressed with sudden load peaks. Zero air pollution becomes attainable when fuel-cells supply the prime power on a hybrid vehicle     

Experimental Investigation of InSight HP<Superscript>3</Superscript> Mole Interaction with Martian Regolith Simulant

The InSight mission launches in 2018 to characterize several geophysical quantities on Mars, including the heat flow from the planetary interior. This quantity will be calculated by utilizing measurements of the thermal conductivity and the thermal gradient down to 5 meters below the Martian surface. One of the components of InSight is the Mole, which hammers into the Martian regolith to facilitate these thermal property measurements. In this paper, we experimentally investigated the effect of the Mole’s penetrating action on regolith compaction and mechanical properties. Quasi-static and dynamic experiments were run with a 2D model of the 3D cylindrical mole. Force resistance data was captured with load cells. Deformation information was captured in images and analyzed using Digitial Image Correlation (DIC). Additionally, we used existing approximations of Martian regolith thermal conductivity to estimate the change in the surrounding granular material’s thermal conductivity due to the Mole’s penetration. We found that the Mole has the potential to cause a high degree of densification, especially if the initial granular material is relatively loose. The effect on the thermal conductivity from this densification was found to be relatively small in first-order calculations though more complete thermal models incorporating this densification should be a subject of further investigation. The results obtained provide an initial estimate of the Mole’s impact on Martian regolith thermal properties.     

西安航空学院大学生思想政治状况调查及分析

提高大学生思政教育效果的关键在于详细了解大学生的思想现状和精神诉求。2012年3月,通过抽样问卷的形式,调查了西安航空学院大学生思想政治的基本情况,并结合调查结果对数据进行了分析,发现大学生思想政治上存在着四方面的问题。这些问题对于有针对性地开展大学生的思想教育提供了重要依据。     

“Dakota Sun”-the next generation solar powered racingvehicle

Based on the experience gained from Sunrayce '95, the Solar Motion Team has made many changes to the design of the next generation solar car. These changes have resulted in a vehicle that is very different from the “Solar Rolar”, The Dakota Sun is a three wheeled vehicle with separate cab and solar array. This design allows for improved aerodynamics, decreased weight, lower rolling resistance, and ease of manufacture compared to the four wheeled catamaran used in the last race. However, this design sacrifices total enclosed wheel base area, additional room for components, and added power from side solar panels, The major objectives for the team's redesigned Sunrayce '97 entry are: systems integration; decrease the weight of the car; decrease aerodynamic drag; more efficient use of available energy; and increased driver safety. The team has set a standard to use the latest available technology. Although this increases the complexity of the components, by using a systems engineering approach the “Dakota Sun” has evolved into a more integrated vehicle. This philosophy of integrated design has resulted in great improvements in mechanical design and manufacturing techniques, as well as electrical innovations. The major design changes evident from the original Sunraycen '95 vehicle are the result of an evolutionary design process that has produced the highly competitive Sunraycel '97 design outlined in this article     

High resolution 3D “snapshot” ISAR imaging and featureextraction

We have developed a new formulation for three dimensional (3D) radar imaging of inverse synthetic aperture radar (ISAR) data based on recent developments in high resolution spectral estimation theory. Typically for non real-time applications, image formation is a two step process consisting of motion determination and image generation. The technique presented focuses on this latter process, and assumes the motion of the target is known. The new technique offers several advantages over conventional techniques which are based on the correlation imaging function. In particular, the technique provides for a direct 3D estimate (versus back projection to a 3D target grid matrix) of the locations of the dominant scattering centers using only a minimum set of independent 2D range-Doppler ISAR “snapshots” of the target. Because of the snapshot nature of the technique, it is particularly applicable to 3D imaging of sectors of sparse-angle data, for which the sidelobes of the correlation imaging integral become high. Furthermore, the technique provides for an estimate of amplitude and phase of each scattering center as a function of aspect angle to the target, for those aspect angles which encompass the set of 2D range-Doppler snapshots. Results illustrating the technique developed are presented for both simulated and static range data     

Comment on “A new approach to robust fault detection andidentification”

In the paper by M. Saif and Y. Guan (see ibid., vol. 3, no 29, p. 685-695), a necessary and sufficient condition is given for the existence of an asymptotically stable observer in the case of p=m. The objective of this note is to point out a critical mistake in the main theorem of the paper     

Potential Effects of Surface Temperature Variations and Disturbances and Thermal Convection on the Mars InSight HP<Superscript>3</Superscript> Heat-Flow Determination

The HP³ instrument on the InSight lander mission will measure subsurface temperatures and thermal conductivities from which heat flow in the upper few meters of the regolith at the landing site will be calculated. The parameter to be determined is steady-state conductive heat flow, but temperatures may have transient perturbations resulting from surface temperature changes and there could be a component of thermal convection associated with heat transport by vertical flow of atmospheric gases over the depth interval of measurement. The experiment is designed so that it should penetrate to a depth below which surface temperature perturbations are smaller than the required measurement precision by the time the measurements are made. However, if the measurements are delayed after landing, and/or the probe does not penetrate to the desired depth, corrections may be necessary for the transient perturbations. Thermal convection is calculated to be negligible, but these calculations are based on unknown physical properties of the Mars regolith. The effects of thermal convection should be apparent at shallow depths where transient thermal perturbations would be observed to deviate from conductive theory. These calculations were required during proposal review and their probability of predicting a successful measurement a prerequisite for mission approval. However, their uncertainties lies in unmeasured physical parameters of the Mars regolith.     

“Reinventing” career development

The following topics are dealt: career development definition; career development as a part of effective management; job satisfaction issues; motivated abilities; a case study results; identification of motivational patterns; and 'reinvention' of career development     

Comments on “Discrete-time observability and estimabilityanalysis for bearings-only target motion analysis”

Discusses the extensive mathematical analysis carried out by the authors of the original paper [see ibid., vol. 33, no. 1, p. 178-201, 1997] and submits the following points. The authors used pseudo measurements for recasting the observability problem into a linear framework. They treated the bearings-only passive target tracking system as a deterministic system. It is already established that for deterministic systems, the pseudo measurements are linear functions of the states of the system, though the coefficient matrix is a nonlinear function of the original measurements, By using the pseudo measurements in a linear observer, global stability can be shown. However, if the pseudo measurement observer, for which the analysis is mostly carried out by the authors, is used in a noisy environment as a pseudo measurement filter (PMF), biased estimates are arrived at. Hence, though the approach of authors is quite direct and provides insights about the algebraic structure of the BOT problem, as pseudo measurements are used throughout the analysis is not of much use to the TMA community, as the nonlinear measurement equation along with measurement noise are required to be considered in the BOT problem to obtain unbiased results     

Supersonic biplane—A review

One of the fundamental problems preventing commercial transport aircraft from supersonic flight is the generation of strong sonic booms. Sonic booms are the ground-level manifestation of shock waves created by airplanes flying at supersonic speeds. The strength of the shock waves generated by an aircraft flying at supersonic speed is a direct function of both the aircraft’s weight and its occupying volume; it has been very difficult to sufficiently reduce the shock waves generated by the heavier and larger conventional supersonic transport (SST) configuration to meet acceptable at-ground sonic-boom levels. It is our dream to develop a quiet SST aircraft that can carry more than 100 passengers while meeting acceptable at-ground sonic-boom levels. We have started a supersonic-biplane project at Tohoku University since 2004. We meet the challenge of quiet SST flight by extending the classic two-dimensional (2-D) Busemann biplane concept to a 3-D supersonic-biplane wing that effectively reduces the shock waves generated by the aircraft. A lifted airfoil at supersonic speeds, in general, generates shock waves (therefore, wave drag) through two fundamentally different mechanisms. One is due to the airfoil’s lift, and the other is due to its thickness. Multi-airfoil configurations can reduce wave drag by redistributing the system’s total lift among the individual airfoil elements, knowing that wave drag of an airfoil element is proportional to the square of its lift. Likewise, the wave drag due to airfoil thickness can also be nearly eliminated using the Busemann biplane concept, which promotes favorable wave interactions between two neighboring airfoil elements. One of the main objectives of our supersonic-biplane study is, with the help of modern computational fluid dynamics (CFD) tools, to find biplane configurations that simultaneously exhibit both traits. We first re-analyzed using CFD tools, the classic Busemann biplane configurations to understand its basic wave-cancellation concept. We then designed a 2-D supersonic biplane that exhibits both wave-reduction and cancellation effects simultaneously, utilizing an inverse-design method. The designed supersonic biplane not only showed the desired aerodynamic characteristics at its design condition but also outperformed a zero-thickness flat-plate airfoil. (Zero-thickness flat-plate airfoils are known as the most efficient monoplane airfoil at supersonic speeds.) Also discussed in this paper is how to design 2-D biplanes, not only at their design Mach numbers but also at off-design conditions. Supersonic biplanes have unacceptable characteristics at their off-design conditions such as flow choking and its related hysteresis problems. Flow choking causes rapid increase of wave drag and it continues to be kept up to the Mach numbers greater the cruise (design) Mach numbers due to its hysteresis. Some wing devices such as slats and flaps, which could be used at take-off and landing conditions as high-lift devices, were utilized to overcome these off-design problems. Then supersonic-biplane airfoils were extended to 3-D wings. Because that rectangular-shaped 3-D biplane wings showed undesirable aerodynamic characteristics at their wingtips, a tapered-wing planform was chosen for the study. A 3-D biplane wing having a taper ratio and aspect ratio of 0.25 and 5.12, respectively, was designed utilizing the inverse-design method. Aerodynamic characteristics of the designed biplane wing were further improved by using winglets at its wingtips. Flow choking and its hysteresis problems, however, occurred at their off-design conditions. It was shown that these off-design problems could also be resolved by utilizing slats and flaps. Finally, a study on the aerodynamic characteristics of wing-body configurations was conducted using the tapered biplane wing. In this study a body was chosen in order to generate strong shock waves at its nose region. Preliminary parametric studies on the interference effects between the body and the tapered biplane wing were performed by choosing several different wing locations on the body. From this study, it can be concluded that the aerodynamic characteristics of the tapered biplane wing are minimally affected by the disturbances generated from the body, and that the biplane wing shows promise for quiet commercial supersonic transport.     

New approaches to weapon system testing or “back to thefuture”

This paper proposes abandoning the use of multipurpose ATE for “horizontal” support of weapon systems in favor of returning to “vertical” support. An R&D effort is proposed to develop a software “hot mock-up” system for field testing weapon system assemblies     

Sedimentation stability of fullerene C<Subscript>60</Subscript> particles in sulphamate nickel-plating electrolyte

The techniques of injecting nanomodifiers into the sulphamate electrolyte used for electrolytic forming of nickel antiabrasive protective tipping are considered. The optimal concentration of surfactant and nanomodifier are determined. The graphs are also presented.     

具有纳米结构的 VO₂ 相变薄膜

 采用无机溶胶-凝胶法制备VO₂相变薄膜，该薄膜相变时的电阻（率）突变可达4～5个数量级。并用XRD,DSC和TGA法研究了制膜过程中干凝胶膜的层状非晶纳米结构。通过适当的非晶晶化过程及随后V₂O₅→VO₂转变的真空热处理，可获得带有空洞（void）结构的低密度纳米薄膜，从而使电阻（率）突变特性异常优异。     

The evolution of massive stars; an observational viewpoint

The review is a discussion of observationally deduced values of the masses, mass-loss rates, temperatures, luminosities and element abundances for the most massive stars. The comparison of these quantities with theoretical calculations is also discussed, in terms of our present understanding of their evolution.     

Generalized approach for μ synthesis of robust switchingregulators

A general method using μ synthesis to design controllers applicable to pulsewidth modulated (PWM) converters is described. System uncertainties from component tolerances are included in the synthesis procedure, adding a quantifiable measure of robustness. Furthermore, these uncertainties have been implemented in a structured format which maximizes available system performance. A boost converter example is presented demonstrating the controller synthesis procedure and advantages of this method     

Magnetospheric Science Objectives of the <Emphasis Type="Italic">Juno</Emphasis> Mission

In July 2016, NASA’s Juno mission becomes the first spacecraft to enter polar orbit of Jupiter and venture deep into unexplored polar territories of the magnetosphere. Focusing on these polar regions, we review current understanding of the structure and dynamics of the magnetosphere and summarize the outstanding issues. The Juno mission profile involves (a) a several-week approach from the dawn side of Jupiter’s magnetosphere, with an orbit-insertion maneuver on July 6, 2016; (b) a 107-day capture orbit, also on the dawn flank; and (c) a series of thirty 11-day science orbits with the spacecraft flying over Jupiter’s poles and ducking under the radiation belts. We show how Juno’s view of the magnetosphere evolves over the year of science orbits. The Juno spacecraft carries a range of instruments that take particles and fields measurements, remote sensing observations of auroral emissions at UV, visible, IR and radio wavelengths, and detect microwave emission from Jupiter’s radiation belts. We summarize how these Juno measurements address issues of auroral processes, microphysical plasma physics, ionosphere-magnetosphere and satellite-magnetosphere coupling, sources and sinks of plasma, the radiation belts, and the dynamics of the outer magnetosphere. To reach Jupiter, the Juno spacecraft passed close to the Earth on October 9, 2013, gaining the necessary energy to get to Jupiter. The Earth flyby provided an opportunity to test Juno’s instrumentation as well as take scientific data in the terrestrial magnetosphere, in conjunction with ground-based and Earth-orbiting assets.     

模型的转捩流动计算分析简

 为了在黏性流动数值模拟中实现边界层转捩的自动预测,将γ-Re_θt转捩模型引入到三维非结构混合网格的雷诺平均Navier-Stokes方程求解程序（HUNS3D）。该转捩模型由两个依赖当地变量定义的关于间歇因子和当地化转捩起始动量厚度雷诺数的输运方程组成,其数值求解算法与流场求解程序中湍流模型的求解方法相同。为了考察和验证HUNS3D程序中γ-Re_θt转捩模型对航空工程中的常见附面层自由转捩问题的预测精度,对低速平板流动、Aerospatial-A翼型、NLR 7301超临界翼型和NASA Trap wing 高升力构型等典型外形的自由转捩流动进行了计算,并将计算结果与相关试验结果进行了对比分析。算例结果表明：γ-Re_θt转捩模型对于转捩位置具有很好的敏感性,能比较准确地预测自然转捩和分离转捩,可以有效提高HUNS3D程序对实际流动的模拟能力和预测精度。