Self-perspiration garment for extravehicular activity improves skin cooling effects without raising humidity

Introduction

The current U.S. extravehicular activity (EVA) suit in space includes liquid cooling and ventilation garment (LCVG) to control thermal condition. Tubes knitted in LCVG for flowing water interrupt evaporation of perspiration, and astronauts feel discomfort. In the present study, we hypothesized that a self-perspiration garment would effectively lower the skin temperature without raising humidity in the garment. Thus, we developed and examined the effects of the garment.

Methods

Eight healthy subjects were studied with a cyclic ergometer of 30, 60 90 and 120 W loading for 3 min each. Skin temperature and humidity on the back were measured continuously. Subjects wore and tested three types of garments i.e., a spandex wear without any cooling device (Normal), a simulated LCVG (s-LCVG) or the spandex wear knitted a vinyl tube for flowing water, and the spandex wear with a tube, which flows water and self-perspiration with oozing water for evaporative cooling (SPEC).

Results

All measurements were reached to steady state 2–3 min after the setting. The s-LCVG decreased skin temperature 0.39±0.14 °C during 12 min of cooling. With SPEC, skin temperature did not decrease significantly until 6–9 min after starting the cooling. However, the temperature decreased rapidly and significantly after that, and finally decreased 1.59±0.32 °C. Humidity in the SPEC was significantly lower than that in s-LCVG.

Discussion

SPEC was effective for lowering skin temperature without raising humidity in the garment. The concept is expected to use as a better cooling system during EVA.     

ICAN: A novel laser architecture for space debris removal

The development of a fiber based laser architecture will enable novel applications in environments which have hitherto been impossible due to size, efficiency and power of traditional systems. Such a new architecture has been developed by the International Coherent Amplification Network (ICAN) project. Here we present an analysis of utilizing an ICAN laser for the purpose of tracking and de-orbiting hyper-velocity space debris. With an increasing number of new debris from collisions of active, derelict and new payloads in orbit, there is a growing danger of runaway debris impacts. Due to its compactness and efficiency, it is shown that space-based operation would be possible. For different design parameters such as fiber array size, it is shown that the kHz repetition rate and kW average power of ICAN would be sufficient to de-orbit small 1–10 cm debris within a single instance via laser ablation.     

Novel design for microstrip to stripline transitions for millimeter-wave application in LTCC

This paper presents two transitions between microstrip and stripline in Low Temperature Co-fired Ceramic technology, including a vertical transition and a coplanar transition for millimeter-wave application. These interconnects are simulated and optimized by a three-dimensional electromagnetic field simulator. Simulation results show that the return loss of microstrip to stripline vertical transition is less than −22 dB, and insertion losses are greater than 0.5 dB up to 35 GHz, and greater than 1 dB up to 40 GHz. Similarly, the return loss of the coplanar transition is less than −32 dB and insertion loss is better than 0.5 dB. LTCC test structures were fabricated and the performance of all transitions was successfully validated by scattering parameter measurements up to 40 GHz.     

Interaction between exercising humans and growing plants in a Closed Ecological Life Support System

The purpose of this study was to quantify the gas exchange between plants growing in a Closed Environmental Life Support System (CELSS) and the metabolism of human subjects undergoing various levels of physical exercise, and subsequently determine the buffer characteristics in relation to the carbon exchange established for plants in this closed loop life support system. Two men (ages 42 and 45 yr) exercised on a cycle ergometer at three different work intensities, each on a separate day. The CELSS, a 113 m³ chamber, was sized to meet the needs of one human. The plants, consisting of 20 m² of potato, provided oxygen to the human during an artificially lighted photosynthesis phase and the human provided CO₂ to the plants. The average rates of exchange for the subjects were 0.88, 1.69, and 2.47 liters O₂/min and 0.77, 1.47, and 2.21 liters CO₂/min at approximately 25%, 50%, and 75% of their maximal aerobic capacity, respectively. The photosynthetic rate for the CELSS was 0.95 liters/ min. A balance between human CO₂ production and plant utilization was noted at approximately the 50% VO_2max level. The oxygen balance and changes were not within detectable limits of the CELSS instrumentation for the durations of these exercise exposures. If a CELSS environment is the methodology selected for long term spaceflight, it will be important to select plants that efficiently grow at the available light and nutrient levels while balancing the needs for the human crew at their levels of physical activity.     

L׳ADROIT – A spaceborne ultraviolet laser system for space debris clearing

Small (1–10 cm) debris in low Earth orbit (LEO) are extremely dangerous, because they spread the breakup cascade. Pulsed laser active debris removal using laser ablation jets on target is the most cost-effective way to re-enter the small debris. No other solutions address the whole problem of large (~100 cm, 1 t) as well as small debris. Physical removal of small debris (by nets, tethers and so on) is uneconomical because of the energy cost of matching orbits. In this paper, we present a completely new proposal relative to our earlier work. This new approach uses rapid, head-on interaction in 10–40 s rather than 4 minutes, using 20–40 kW bursts of 100 ps, 355 nm UV pulses from a 1.5 m diameter aperture on a space-based station in LEO. The station employs “heat-capacity” laser mode with low duty cycle to create an adaptable, robust, dual-mode system which can lower or raise large derelict objects into less dangerous orbits, as well as clear out the small debris in a 400-km thick LEO band. Time-average laser optical power is less than 15 kW. The combination of short pulses and UV wavelength gives lower required fluence on target as well as higher momentum coupling coefficient. An orbiting system can have short range because of high interaction rate deriving from its velocity through the debris field. This leads to much smaller mirrors and lower average power than the ground-based systems we have considered previously. Our system also permits strong defense of specific assets. Analysis gives an estimated cost less than $1 k each to re-enter most small debris in a few months, and about 280 k$ each to raise or lower 1-ton objects by 40 km. We believe it can do this for 2000 such large objects in about four years. Laser ablation is one of the few interactions in nature that propel a distant object without any significant reaction on the source.     

CCISS,Vascular and BP Reg: Canadian space life science research on ISS

A comprehensive goal of the Canadian Space Agency studies (CCISS, Vascular and BP Reg) has been to investigate the efficacy of current exercise countermeasures to maintain cardiovascular and cerebrovascular health on return to Earth after up to 6-months in space. Results from the CCISS experiments revealed no significant change of in-flight heart rate during daily activities or sleep, and small, but variable between astronauts, post-flight elevation. The between astronaut differences were exaggerated during measurement of spontaneous baroreflex slope, which was reduced post-flight (P<0.05) during paced breathing with 3 astronauts having significant correlations between reduced baroreflex and reduced RR-interval (consistent with reduced fitness). Cerebrovascular autoregulation and CO₂ response were mildly impaired after flight. Some loss of in-flight fitness of astronauts in Vascular was reflected by the increase in HR at a work rate of 161±46 W of 12.3±10.5 bpm, 10.4±5.9 bpm and 13.4±5.7 bpm for early-flight, late-flight and R+1, respectively. On return to gravity, changes in resting heart rate for supine (5.9±3.5 bpm), sit (8.1±3.3 bpm) and stand (10.3±10.0 bpm) were small but variable between individuals (from −5 bpm to +20 bpm in post-flight standing) and not related to the change in exercise heart rate. In Vascular astronauts, pulse wave transit time measured to the finger tended to be reduced post-flight and carotid artery distensibility was significantly reduced (P=0.03, and n=6). The heart rate and baroreflex data suggest that some astronauts return with cardiovascular deconditioning in spite of the exercise regimes. However, greater arterial stiffness is common among all astronauts studied to date. The new CSA project, BP Reg, will monitor inflight blood pressure in an attempt to identify astronauts in greater need for countermeasures. Future research should focus on whether Vascular changes in astronauts might make them an appropriate model to study the mechanisms of arterial aging on Earth.     

Optical orbital debris spotter

The number of man-made debris objects orbiting the Earth, or orbital debris, is alarmingly increasing, resulting in the increased probability of degradation, damage, or destruction of operating spacecraft. In part, small objects (<10 cm) in Low Earth Orbit (LEO) are of concern because they are abundant and difficult to track or even to detect on a routine basis. Due to the increasing debris population it is reasonable to assume that improved capabilities for on-orbit damage attribution, in addition to increased capabilities to detect and track small objects are needed. Here we present a sensor concept to detect small debris with sizes between approximately 1.0 and 0.01 cm in the vicinity of a host spacecraft for near real time damage attribution and characterization of dense debris fields and potentially to provide additional data to existing debris models.     

A direct fusion drive for rocket propulsion

The Direct Fusion Drive (DFD), a compact, anuetronic fusion engine, will enable more challenging exploration missions in the solar system. The engine proposed here uses a deuterium–helium-3 reaction to produce fusion energy by employing a novel field-reversed configuration (FRC) for magnetic confinement. The FRC has a simple linear solenoid coil geometry yet generates higher plasma pressure, hence higher fusion power density, for a given magnetic field strength than other magnetic-confinement plasma devices. Waste heat generated from the plasma?s Bremsstrahlung and synchrotron radiation is recycled to maintain the fusion temperature. The charged reaction products, augmented by additional propellant, are exhausted through a magnetic nozzle. A 1 MW DFD is presented in the context of a mission to deploy the James Webb Space Telescope (6200 kg) from GPS orbit to a Sun–Earth L2 halo orbit in 37 days using just 353 kg of propellant and about half a kilogram of ³He. The engine is designed to produce 40 N of thrust with an exhaust velocity of 56.5 km/s and has a specific power of 0.18 kW/kg.     

Conceptual design of a hypervelocity asteroid intercept vehicle (HAIV) and its flight validation mission

An intercept mission with nuclear explosives is the most effective of the practical mitigation options against the impact threat of near-Earth objects (NEOs) with a short warning time (e.g., much less than 10 years). The existing penetrated subsurface nuclear explosion technology limits the intercept velocity to less than approximately 300 m/s. Consequently, an innovative concept of blending a hypervelocity kinetic impactor with a subsurface nuclear explosion has been developed for optimal penetration, fragmentation, and dispersion of the target NEO. A proposed hypervelocity asteroid intercept vehicle (HAIV) consists of a kinetic-impact leader spacecraft and a follower spacecraft carrying nuclear explosives. This paper describes the conceptual development and design of a baseline HAIV system and its flight validation mission architecture for three mission cost classifications (e.g., $500 M, $1 B, and $1.5 B).     

Life-sciences research opportunities in commercial suborbital space flight

Commercial suborbital space flights will reach altitudes above 100 km, with 3–5 min of weightlessness bracketed by high-g launch and landing phases. The proposed frequency of these flights, and the large passenger population, present interesting opportunities for researchers in the life sciences. The characteristics of suborbital flight are between those of parabolic and orbital flights, opening up new scientific possibilities and easing the burden for obtaining access to 0g.     

Going to Alpha Centauri B and setting up a Radio Bridge

How to exploit the Sun as a gravitational lens has been studied extensively during the last 20 years, especially by this author (Refs. 1, 2, 3, 4, 5, 6 and 7). In essence, a spacecraft dubbed FOCAL (an acronym for “Fast Outgoing Cyclopean Astronomical Lens”) should be launched in the direction of the sky opposite to the area of the sky we wish to see highly magnified both at radio and other frequencies. After FOCAL reached the minimal focal distance of 550 AU from the Sun, highly magnified radio images of celestial objects located on the opposite side of the Sun will automatically be produced. In this paper we apply the FOCAL mission concept to the goal of exploring the neighborhood of the Alpha Centauri B star, where the nearest exoplanet to the Solar system was recently discovered. We suggest that:     

Extrasolar solar-sail trajectories and dark matter

Hyper-thin, high-speed solar-photon sail space probes exploring the Sun?s Oort comet cloud could also be used to set an upper bound to the concentration of WIMPS (weakly interacting massive particles), one of the suggested (but unconfirmed) forms of dark matter within the vicinity of the solar system. Newton?s Shell Theorem would be applied to determine variations in apparent solar mass as the probe moves further out from the Sun. Application of this technique to the trajectories of Pioneer 10/11 reveals that the upper limit to WIMP concentration within ~60 AU of the Sun is ~0.2 Earth masses, as revealed in studies of the Pioneer Anomaly. If the published accuracy of the Pioneer acceleration measurements can be increased by an order of magnitude, probe trajectory measurements out to ~10,000 AU may confirm or falsify the hypothesis that WIMP mass within the solar vicinity is ~3X star mass. It is shown that a space-manufactured ~40-nm thick beryllium hollow-body solar sail deployed from a ~0.07 AU perihelion is a candidate spacecraft for such a mission. Possible science-team organization strategy for a ~100-year mission to ~10,000 AU is discussed.     

Debris dispersion effect in N-shape configuration

Spacecraft shields play an important role in shielding against the impact of space debris. Increasing the dispersion degree of the debris produced by the impact of the space debris on the bumper of configuration is able to lower the concentration of debris impacting on the rear plate and thus to reduce the risk of debris perforating the rear plate. In order to improve the dispersion degree, the N-shape configuration is proposed and studied by hypervelocity impact test with the velocity of 4.80 km/s and numerical simulation with the velocities ranging from 3.0 km/s to 7.0 km/s. As a comparison, the distribution of debris impacting on the rear plate is also investigated for the parallel triple-wall configuration with the same areal density. It is found that this degree is increased in the N-shape configuration due to the oblique plate, and therefore the risk of debris perforating the rear plate is reduced compared to the case of parallel triple-wall configuration.     

Hesperides: Solar/nuclear missions to the Sun׳s inner gravity focus

The Sun?s gravity focus at >550 AU is of interest to astrophysicists including SETI scientists, researchers seeking to image extra-solar planets and others. One method for an extra-solar probe to reach the Sun?s inner gravity focus within a human working lifetime (less than 50 years) is to combine solar and nuclear propulsion techniques. Here, we present a non-optimized probe concept including state-of-the-art solar-sail, radioisotope-electric propulsion and giant-planet gravity assists. Application of radioisotope propulsion allows some cross range capability during and after the powered and cruise phases of the flight to >600 AU. Such a capability is likely necessary to fully utilize the solar gravitational lens effect for SETI and astrophysical observations.     

Control system design of the Korean lunar lander demonstrator

In preparation for the lunar exploration program scheduled to be launched during the early 2020s in Korea, a lunar lander demonstrator, which will be used for developing and demonstrating lunar landing technologies, is being developed. The control configuration of the lunar lander demonstrator is determined with the consideration of available technologies and flight requirements. It is suggested that altitude control be achieved by clustering five 200 N monopropellant thrusters and attitude control with eight 3 N thrusters. A control algorithm designed to follow a predefined trajectory is developed using quaternion feedback. Control system configuration and control logic are verified by using computer simulations. Simulation results show that a soft landing with a touchdown velocity of less than 3 m/s is achieved. Attitude control performance is also verified using computer simulations. The developed control configuration will be further tested by hardware in the loop simulations and ground based firing tests during the next phase of the study.     

High velocity impact characterization of Al alloys for oblique impacts

This paper describes the experimental and computational analyses of a high velocity aluminum projectile impact on an Al6061-T6 spacecraft inner wall at different oblique angles. Al2017-T4 spherical projectiles of 5.56 mm in diameter and 0.25 g in weight were chosen within the velocity range of 1000±200 m/s due to the limitation of the light gas gun. The energy absorbed was calculated by measuring the velocities before and after impact on the inner wall. The energy absorbed by the wall and the remaining energy carried by the projectile helped to estimate the severity of further damage to inner components. Afterwards, validation was done by using the commercially available software LS-DYNA with a dedicated SPH. On average, a 10% energy absorption difference between experimentation and simulation was found. By using C-SCAN, the damage area proportion of the total inner wall to impact penetration hole area was found to be on average 6%, 26% and 53% greater than the projectile cross sectional area for the oblique angle impacts of 30°, 45°, and 60°, respectively. These findings helped to understand the relationship between the oblique impact event and the damage area on a spacecraft inner wall along with space debris cloud propagation and comparison with experimental results using LS-DYNA.     

Optimal nodal flyby with near-Earth asteroids using electric sail

The aim of this paper is to quantify the performance of an Electric Solar Wind Sail for accomplishing flyby missions toward one of the two orbital nodes of a near-Earth asteroid. Assuming a simplified, two-dimensional mission scenario, a preliminary mission analysis has been conducted involving the whole known population of those asteroids at the beginning of the 2013 year. The analysis of each mission scenario has been performed within an optimal framework, by calculating the minimum-time trajectory required to reach each orbital node of the target asteroid. A considerable amount of simulation data have been collected, using the spacecraft characteristic acceleration as a parameter to quantify the Electric Solar Wind Sail propulsive performance. The minimum time trajectory exhibits a different structure, which may or may not include a solar wind assist maneuver, depending both on the Sun-node distance and the value of the spacecraft characteristic acceleration. Simulations show that over 60% of near-Earth asteroids can be reached with a total mission time less than 100 days, whereas the entire population can be reached in less than 10 months with a spacecraft characteristic acceleration of 1 mm/s².     

Earth observation with MEO transmitters and UAS receivers: A potential utilization of Galileo constellation

Remote sensing application of Galileo upcoming constellation in the field of civil security is preliminarily analyzed, defining low resolution (25 m) and high resolution (7.5 m) working modes for a bistatic Synthetic Aperture Radar system utilizing Galileo satellites as transmitters and Unmanned Aerial Systems as receivers. Simulations offshore Somali coast and in a South Mediterranean Sea region showed that both low and high resolution acquisitions are feasible. For the low resolution mode a probability of successful image formation no matter the azimuth position of the receiving UAS has been estimated at nearly 100%. Whereas, for the high resolution mode it decreases to about 90%, which, if deemed unsatisfactory for the application, leads to the need for UAS to adapt its route to the actual Galileo satellite coverage.     

Applications of tuned mass dampers to improve performance of large space mirrors

In order for future imaging spacecraft to meet higher resolution imaging capability, it will be necessary to build large space telescopes with primary mirror diameters that range from 10 m to 20 m and do so with nanometer surface accuracy. Due to launch vehicle mass and volume constraints, these mirrors have to be deployable and lightweight, such as segmented mirrors using active optics to correct mirror surfaces with closed loop control. As a part of this work, system identification tests revealed that dynamic disturbances inherent in a laboratory environment are significant enough to degrade the optical performance of the telescope. Research was performed at the Naval Postgraduate School to identify the vibration modes most affecting the optical performance and evaluate different techniques to increase damping of those modes. Based on this work, tuned mass dampers (TMDs) were selected because of their simplicity in implementation and effectiveness in targeting specific modes. The selected damping mechanism was an eddy current damper where the damping and frequency of the damper could be easily changed. System identification of segments was performed to derive TMD specifications. Several configurations of the damper were evaluated, including the number and placement of TMDs, damping constant, and targeted structural modes. The final configuration consisted of two dampers located at the edge of each segment and resulted in 80% reduction in vibrations. The WFE for the system without dampers was 1.5 waves, with one TMD the WFE was 0.9 waves, and with two TMDs the WFE was 0.25 waves. This paper provides details of some of the work done in this area and includes theoretical predictions for optimum damping which were experimentally verified on a large aperture segmented system.     

发动机和羽流对地球同步卫星底部辐射加热的计算研究

地球同步卫星工作过程中法兰底座所受的辐射加热对法兰上的控制开关等零件的安全有重要影响。为此,建立了节点网络法计算发动机和隔热屏对卫星法兰底座及控制开关的辐射加热,比较了发动机、隔热屏和羽流3种辐射源的作用大小,还研究了发动机位置的平移对底部法兰及控制开关辐射加热的影响。研究表明:羽流对法兰和控制开关的辐射热流最小,发动机对法兰和控制开关的辐射热流最大;法兰和控制开关上不同侧面受到的辐射加热很不均匀,面向发动机正面的侧面辐射加热最强,面向发动机头部的侧面辐射最小;发动机向后平移可以显著降低法兰和控制开关上辐射热流的最大值。