煤油/氧气同轴离心喷嘴燃烧数值模拟

为了更好地了解同轴离心喷嘴的工作特性,基于DDES模型研究了油气比分别为0.5、1、1.5下以煤油/氧气为推进剂的喷嘴的流体动力学特性与非预混燃烧特征.研究结果表明:由于旋流离心作用,在喷嘴出口轴心处和燃烧室顶部分别存在一个驻定涡和角涡,驻定涡径向分布在0.9 R～1.4 R,轴向尺寸在-1 R～14 R,随着燃料流量...     

Droplet vaporization in supercritical pressure environments

For most liquid-fueled combustion systems the behavior of the fuel as it is introduced to the combustion zone, often by spray injection, will have a significant impact on combustion. The subsequent combustion may be affected to a considerable degree by the initial spread of the liquid, break-up of larger fuel sheets and droplets into droplets of various sizes, droplet vaporization, and diffusion of gaseous fuel. Among the many factors which affect spray break-up and droplet vaporization are the environmental conditions into which the spray is introduced. For both diesel engines and rockets the environment pressure and temperature may be above the critical pressure and temperature of the injected fuel. In a compression-ignition internal combustion engine, the environment consists primarily of air, at pressures from 20 to 100 atmospheres and temperatures ranging from 900 to 1500 K. Even higher pressures are encountered in turbocharged diesels. A typical diesel reference fuel, dodecane, has a thermodynamic critical pressure of about 17 atmospheres, and a critical temperature of 600 K. Fuel is injected into a diesel engine environment in which ambient pressures exceed the critical pressure. While droplet temperatures are subcritical at first, they may rise to the critical temperature or higher.This paper will survey current understanding of supercritical pressure droplet vaporization. Specifically, the topics covered will include: liquid phase behavior; vapor phase behavior; thermodynamic and transport properties; droplet distribution and break-up; micro-explosions; and effects of microgravity.     

壁面孔型对超声速气流中喷注特性的影响

超声速气流中,燃料与来流空气的高效混合是燃烧室实现点火、稳焰及高效燃烧组织的前提。国内外研究者已对比研究了不同壁面孔型对超声速气流中喷注、混合特性的影响,相比于最常见的圆形喷孔,菱形、楔形-半圆、箭形及针形等喷孔用于超声速气流燃料喷注时,不仅有利于降低喷孔前缘边界层的分离,而且也有利于提升射流穿透深度;相比于单孔喷注,组合型喷孔能进一步增强燃料与来流空气在射流远场的混合效果。通过综述各型喷孔的喷注特性,分析提出了适用于超声速燃烧组织的壁面喷注孔型及其工程应用条件。     

超临界环境下煤油和UDMH单滴燃烧现象

采用重活塞实验系统,对煤油和UDMH在超临界环境下的蒸发和燃烧现象进行了初步研究,结果表明:无论液态或者凝胶燃料,在超临界环境下均存在蒸发现象。在空气超临界环境下,煤油和UDMH均产生自燃现象。自燃呈现多点着火现象,类似于"森林火灾"模式,且持续时间较长。燃烧大致可分为蒸发、点火、燃烧前期和燃烧后期4个阶段。     

Evaporation and ignition of droplets in combustion chambers modeling and simulation

Computer simulation of liquid fuel jet injection into heated atmosphere of combustion chamber, mixture formation, ignition and combustion need adequate modeling of evaporation, which is extremely important for the curved surfaces in the presence of strong heat and mass diffusion fluxes. Combustion of most widely spread hydrocarbon fuels takes place in a gas-phase regime. Thus, evaporation of fuel from the surface of droplets turns to be one of the limiting factors of the process as well. The problems of fuel droplets atomization, evaporation being the key factors for heterogeneous reacting mixtures, the non-equilibrium effects in droplets atomization and phase transitions will be taken into account in describing thermal and mechanical interaction of droplets with streaming flows. In the present paper processes of non-equilibrium evaporation of small droplets will be discussed. As it was shown before, accounting for non-equilibrium effects in evaporation for many types of widely used liquids is crucial for droplet diameters less than 100 μm, while the surface tension effects essentially manifest only for droplets below 0.1 μm. Investigating the behavior of individual droplets in a heated air flow allowed to distinguish two scenarios for droplet heating and evaporation. Small droplets undergo successively heating, then cooling due to heat losses for evaporation, and then rapid heating till the end of their lifetime. Larger droplets could directly be heated up to a critical temperature and then evaporate rapidly. Droplet atomization interferes the heating, evaporation and combustion scenario. The scenario of fuel spray injection and self-ignition in a heated air inside combustion chamber has three characteristic stages. At first stage of jet injection droplets evaporate very rapidly thus cooling the gas at injection point, the liquid jet is very short and changes for a vapor jet. At second stage liquid jet is becoming longer, because evaporation rate decreases due to decrease of temperature. But combustion of fuel vapor begins which brings to increase of heat flux to droplets and accelerates evaporation. The length of the liquid jet decreases again and remains constant slightly oscillating.     

Combustion performance and scale effect from N2O/HTPB hybrid rocket motor simulations

HRM code for the simulation of N₂O/HTPB hybrid rocket motor operation and scale effect analysis has been developed. This code can be used to calculate motor thrust and distributions of physical properties inside the combustion chamber and nozzle during the operational phase by solving the unsteady Navier–Stokes equations using a corrected compressible difference scheme and a two-step, five species combustion model. A dynamic fuel surface regression technique and a two-step calculation method together with the gas–solid coupling are applied in the calculation of fuel regression and the determination of combustion chamber wall profile as fuel regresses. Both the calculated motor thrust from start-up to shut-down mode and the combustion chamber wall profile after motor operation are in good agreements with experimental data. The fuel regression rate equation and the relation between fuel regression rate and axial distance have been derived. Analysis of results suggests improvements in combustion performance to the current hybrid rocket motor design and explains scale effects in the variation of fuel regression rate with combustion chamber diameter.     

中心进气旋转射流冲压燃烧室湍流流动数值模拟

采用Reynolds应力方程模型及涡耗散燃烧模型,对头部进气式固体火箭冲压发动机二次燃烧二维轴对称反应流场进行了数值模拟,研究了空气射流和燃气射流无旋、同向旋转和反向旋转3种进气方式对二次燃烧的影响。研究结果表明,当空气射流和燃气射流以有旋状态进入补燃室时,燃料与空气的混合速度变快,化学反应更快,燃烧也更为充分。     

采用多级主火箭的RBCC发动机性能分析(英文)

采用三维两相数值模拟技术研究火箭基组合推进(RBCC)发动机的燃烧。提出了一种新的主火箭布置方式,该方式采用多级主火箭,一级嵌入到支板之中,另一级置于燃烧室中部上壁面。研究表明,相对于常规的主火箭布局,多级主火箭布局能明显提升发动机性能。置于支板的一级火箭以恰当比工作,起到引射和改善进气道工作特性的作用;二级火箭以富燃状态工作,起到火焰稳定和促进燃烧的作用。多级火箭喷射方案是DAB和SMC模式的综合,可作为火箭引射模态改善二次燃烧一种新的方式。     

双推力室起动同步性研究

我国新一代大推力液氧/煤油补燃发动机采用双推力室方案,发动机起动时存在推力室点火不同步情况.以500 t级液氧/煤油补燃发动机为研究对象,针对起动时推力室点火不同步问题,对发动机推力室燃料路的控制方案进行了研究.建立了描述补燃循环发动机起动过程的数学模型,搭建了双推力室发动机起动仿真平台.通过对推力室燃料路两种控制方案的对比分析：指出了从降低发动机系统对双推力室不同步点火的敏感程度考虑,采用2个燃料节流阀分别控制各分支燃料路的方案较优;推力室燃料路采用一个燃料节流阀的控制方案时,推力室冷却套流阻偏差不宜大于1 MPa.     

Influences of the turbulence model and the slot width on the transverse slot injection flow field in supersonic flows

Transverse slot injection scheme is very important for the mixing process between the air and the fuel in supersonic flows. The effect of the turbulence model and slot width on the transverse slot injection flow field has been investigated numerically based on the grid independency analysis, and the predicted results have been compared with the experimental data available in the open literature. The obtained results show that the grid scale makes only a slight difference to the wall pressure profiles for all jet-to-crossflow pressure ratios employed in this study, and the wall pressure profile with low jet-to-crossflow pressure ratio is predicted accurately by the RNG k–ε turbulence model, the SST k–ω turbulence model for the flow field with high jet-to-crossflow pressure ratio. High jet-to-crossflow pressure ratio can increase the jet penetration depth in supersonic flows, and the gradient of the length of the upstream separation region is larger than that of the height of the Mach surface. At the same time, when the jet-to-crossflow pressure ratio is maintained constant, the jet penetration depth increases with the increase of the slot width.     

轴对称结构RBCC发动机超燃模态试验和数值模拟

为研究轴对称结构RBCC发动机超燃模态下的点火和燃烧性能,进行了地面直连试验。采用中心支板火箭与小支板组喷注相结合的方式作为点火和火焰稳定方式,并对燃料喷注方案进行了研究。试验与数值模拟结果表明,采用这种点火方式能实现轴对称结构RBCC发动机的可靠点火和稳定燃烧。二次燃料采取多级喷注的方式能充分利用流道中的氧气,实现较充分的燃烧,但应控制燃料喷注比例。双支板组的加入,能促进燃料与中心空气流的充分掺混,提升燃烧效率,获得较优的燃烧性能。     

燃气喷射角度对含硼固体火箭超燃冲压发动机补燃室燃烧效率的影响

固体火箭燃气超燃冲压发动机具有高比冲、结构简单、流量易调节等优点,然而在超音速空气流的补燃室中,如何让燃料更好地与空气掺混,增加颗粒停留时间,在较短时间内释放出更多的燃烧焓成为目前研究的重点。采用Realiazble k-ε湍流模型,单步涡团耗散模型,在King的硼颗粒点火燃烧模型的基础上考虑了硼颗粒在高速气流当中的气动剥离效应,利用龙格-库塔算法迭代计算硼颗粒点火燃烧过程,对燃气进气方向与轴向夹角从45°~180°的10种进气方式下的补燃室进行了三维两相燃烧流动计算,分析了各种进气角下的燃气燃烧效率、硼颗粒燃烧效率以及总燃烧效率。结果表明:当一次燃气喷射角度与轴向夹角逐渐增加时,燃气与颗粒燃烧效率逐渐增加,并在180°时燃烧效率和比冲为最高。     

Mg粉/CO2粉末火箭发动机点火试验研究

初步设计了粉末火箭发动机,并以Mg粉作为燃料、CO2作为氧化剂进行了点火试验.研究结果表明,在一定的压强和温度下,利用空气与Mg粉的燃烧放热可成功引燃Mg粉/CO2,且在关闭空气后达到自持燃烧；燃烧室壁面沉积较多,主要以MgO为主,还有一部分未燃烧的Mg；通过该试验验证了Mg粉/CO2粉末火箭发动机方案的可行性.     

煤油温度对于爆震波形成影响的实验研究

在内径为30mm的脉冲爆震发动机模型上，以煤油为燃料，以空气为氧化剂，成功地进行了两相爆震实验，获得了充分发展的脉冲爆震波。测试了在化学恰当比，不同爆震频率及燃油温度下的爆震波压力，并对其变化进行了分析。通过分析实验结果发现，在化学恰当比下，爆震频率不变时，煤油温度的升高明显促进了爆震的形成，在内径小于混合物胞格尺寸的爆震管内，可以形成充分发展的两相脉冲爆震波。     

铣槽结构液体火箭发动机推力室壳体热应力分析

介绍了液体火箭发动机推力室铣槽结构热应力的数值分析方法,通过建立液体火箭发动机推力室的流场燃烧和导热理论模型,运用有限体积法考虑液膜冷却计算出发动机工作时的燃气、燃烧室壳体和冷却工质的温度场,将得出的结果作为壳体热应力计算模型的边界条件进行热应力场有限元分析。内、外壁温度的计算数据与实验结果基本相符。     

Numerical study on operating characteristics of a magnesium-based fuel ramjet

A two-dimensional axis symmetrical model for multi-phase turbulent combustion simulation has been developed in a magnesium-based fuel ramjet, the stochastic model is applied to track the motion and transportation of discrete phase in the whole flow field in Lagrangian frame. Firstly, the flow field parameters distribution including temperature, velocity, Mg particle burning rate, main components are obtained to describe the basic operating characteristics, and the thermoacoustic oscillation during the combustion process is predicted due to the observed vortex. Then combined with the developed thermodynamic calculation program, the influencing rules of water/fuel ratio and magnesium-based fuel composition ratio on ramjet operating characteristics are analyzed. The results obtained show that the distribution of two water/fuel ratios exerts a direct impact on the temperature fluctuations in combustor, further influences the combustion stability, as for theoretical specific impulse, a maximal value is observed along with the total water/fuel ratio, while the monotonous trends for thermal efficiency and propulsive efficiency are achieved respectively. Moreover, the magnesium-based fuel composition ratio is a dominant factor to influence the operating characteristics, and it is proved that the high-proportion Mg in fuel is beneficial to specific impulse augment through validation of both simulation results and thermodynamic calculation results.     

Two-phase flow effect on hybrid rocket combustion

This study numerically explores the aerodynamic and combustion processes in a hybrid rocket combustor, under a two-phase turbulent flow environment, considering the evaporation, combustion and drag of droplet and droplet ignition criterion. The predictions of temperature, reaction mode, reactant mass fraction, velocity, oxidizer consumption, fuel regression and droplet number distribution enhance understanding of the two-phase combustion aerodynamics inside the combustor. A parametric study of the inlet spray pattern, including spray cone angle, spray injection velocity and droplet size, is performed to improve the operation of reactant mixing and higher fuel regression rate. Analytical results indicate that both the oxidizer consumption and the fuel regression increase with increasing spray cone angle and spray injection velocity in the practical range of operation. However, for stoichiometric operation, the superior spray cone angle is within 20–60°, and spray injection velocity within 20–40 m/s, under a volume-mean droplet radius of 50 μm. The power dependence of solid-fuel regression on total mass flux is found to decrease with rising of droplet mean size.     

纳米铝粉及纳米铝粉/煤油凝胶体系能量性能研究

测定了各单组分及纳米铝粉／煤油凝胶体系的燃烧热,表征了纳米铝粉及纳米铝粉／煤油凝胶体系的能量性能。实验结果表明,随着纳米铝粉含量的增加,纳米铝粉／煤油凝胶体系的质量恒容燃烧热呈降低趋势,这是由于煤油的燃烧热值较高,铝粉的燃烧热值较低所致;而各纳米铝粉／煤油凝胶体系的密度随纳米铝粉含量的增加呈升高趋势,体系的体积燃烧热也随纳米铝粉含量增加而升高。     

凹腔超声速燃烧室氢气燃烧流场数值模拟

对带长深比为10的凹腔结构的燃烧室二维氢燃烧流场进行数值模拟,燃料喷注方式采用凹腔上游喷注加辅加凹腔前壁、底壁、后壁喷注。采用三阶MUSCL格式求解二维含组分守恒N-S方程组,湍流模型采用剪切修正的RNGk-ε湍流模型,对喷氢燃烧工况进行了计算研究,并分别分析了凹腔中不同燃料喷注方式对燃烧特性的影响。结果表明：凹腔是火焰驻留的主要区域;凹腔上游喷注氢,可以使燃料在凹腔中混合燃烧,辅加凹腔中喷氢的三种方式对燃烧状况产生一定的影响。在凹腔前壁、底面辅加喷氢,没有增强凹腔的稳焰特性,对整个燃烧状态影响不大;在凹腔后壁喷氢,能够增加凹腔中的燃料含量,加强了回流效果,对燃烧状态影响较大。三种喷注方式都没有从根本上改变凹腔燃烧流场的特性。     

过氧化氢／煤油发动机推力室气液燃烧数值模拟

采用离散相模拟颗粒随机轨道方法处理两相流动,采用SST后刊湍流模型,利用燃料的单步总反应模型模拟煤油蒸汽燃烧,针对过氧化氢／煤油发动机推力室,进行三维两相燃烧数值模拟。对推力室的总体流场特征及性能进行了初步研究,为开展进一步的数值研究奠定基础。