A multioutput LLC-type parallel resonant converter

When an LLC-type parallel resonant converter (LLC-PRC) operates above resonant frequency, the switching transistors can be turned off at zero voltage. Further study reveals that the LLC-PRC possesses the advantage of lower converter voltage gain as compared with the conventional PRC. Based on the analytic results derived, a complete set of design curves from which a systematic design procedure is developed is obtained. Experimental results from a 150-W, 150-kHz, multioutput LLC-type PRC power supply are presented     

Comments, with reply, on `Parallel resonant converter with LLC-typecommutation'

In a recent paper by C.Q. Lee et al. (ibid., vol.25, no.6, p. 844-7, Nov. 1989), the authors analyzed a DC-DC converter that they termed the LLC-type PRC (parallel resonant converter). Its resonant network contains three active components-two inductances and a parallel capacitance-and as a consequence the converter might be expected to have third-order dynamics. But Lee et al. employed a matrix transformation to show that the behavior of the circuit may be represented as a state-plane trajectory, as for a second-order circuit. The purpose of this contribution is to show that the converter has a zero-frequency eigenvalue, associated with undesirable circulating DC. The second-order dynamics exhibited by the third-order converter are explained by an application of Thevenin's theorem. Some aerospace applications of the LLC-type parallel resonant converter (PRC) are discussed. In their reply, the authors show that the circulating direct current does not exist in the practical converter circuit     

Effect of FET output capacitance on ZVS of resonant converters

The analysis of resonant converters including the capacitance of the switches is presented. New dc characteristics are obtained for the series, parallel, and series-parallel resonant converters (SPRC). The operating regions where the converters operate with zero-voltage switching (ZVS) are determined as a function of the switch capacitance. The more pronounced effect can be seen in the series resonant converter (SRC), while the parallel resonant converter (PRC) is the most insensitive. The results of the analysis have been verified on an experimental prototype     

Effects of output filter on cross regulation in SRC

Cross regulation performance of multioutput series resonant converter (SRC) topologies using capacitive or inductive filters is analyzed. The steady state cross regulation characteristics are derived using the state-plane techniques and are illustrated by the examples of two-output SRCs with capacitive and inductive filters. The characteristic curves show that over some range of output currents, the cross regulation performance of an SRC with an inductive filter is much improved over the SRC with capacitance filter and less dependent on the tolerances in leakage inductances and the loading on unregulated outputs. It is shown that the converter control characteristics of an SRC with an inductive filter are relatively unaffected by the addition of the second output. The theoretical results are verified by simulation     

Design and technology of compact high-power converters

New material technologies such as Silicon Carbide (SiC) are promising in the development of compact high-power converters for next-generation power electronics applications. This paper presents an optimized converter design approach that takes into consideration non-linear interactions among various converter components, source and load. It is shown that with the development of high-temperature, high-power SiC power module technology, magnetic components and capacitors become important technology challenges, and cannot be ignored. A 50% improvement in power density is calculated for a 100 V-2 kV, 7 kW SiC DC-DC power converter operating at 150°C compared to a silicon power converter. The SiC power converter can be operated at junction temperatures in excess of 300°C (as compared to 150°C for a silicon power converter) with reasonable efficiency that potentially leads to a significant reduction in thermal management     

Simplified analysis of PWM converters using model of PWM switch.II. Discontinuous conduction mode

For pt.I see ibid., vol.26, no.3, p.490-6 (1990). According to the method of state-space averaging, when a pulsewidth modulation (PWM) converter enters discontinuous conduction mode (DCM), the inductor current state is lost from the average model of the converter. It is shown that there is neither theoretical nor experimental justification for the disappearance of the inductor state as claimed by the method of state-space averaging. For example, when the model of the PWM switch in DCM is substituted in the buck, boost, or buck-boost converter while the inductor is left intact, the average model has two poles: the first pole f_p1 agrees with the single pole of state-space averaging, while the second pole f_p2 occurs in the range f_p2⩾F_s/π. It is shown that the right-half plane zeros present in the control-to-output transfer functions of the boost, buck-boost, and Cuk converters in continuous conduction mode are also present in discontinuous conduction mode     

Inherent Overload Protection for the Series Resonant Converter

The overload characteristics of the full bridge series resonant power converter are considered. This includes analyses of the two most common control methods presently in use. The first of these uses a current zero crossing detector to synchronize the control signals and is referred to as the ? controller. The second is driven by a voltage controlled oscillator and is referred to as the ? controller. It is shown that the ? controller has certain reliability advantages in that it can be designed with inherent short circuit protection. Experimental results are included for an 86 kHz converter using power metal-oxide-semiconductor field-effect transistors (MOSFETs).     

Analysis of series-parallel resonant converter

A frequency-domain steady-state analysis is given for a series-parallel resonant converter (SPRC) operating in the continuous conduction mode (CCM) using Fourier series techniques. Equations for performance parameters are derived under steady-state conditions to provide simple design tools. The topology of the SPRC combines the advantageous properties of both the series resonant converter (SRC) and the parallel resonant converter (PRC). The key results of the work are: a novel half-wave rectifier SPRC, conditions for obtaining high part-load efficiency; and several boundary frequencies and limiting conditions such as the capacitive/inductive load boundary and open-circuit and short-circuit cases. Experimental results measured for an 80-W converter above the resonance at different load resistances and input voltages show excellent agreement with the theoretical performance predicted by the equations     

LLC parallel resonant converter design by scaling the LC converter

An efficient and practical method for steady-state design of an LLC-type parallel resonant dc/dc converter (LLC-PRC) is presented. In general, the output characteristic curves of LLC-PRC can be obtained by multiplying the output curves of the LC-type parallel resonant converter (LC-PRC) by a ratio of the parallel and series inductances. The peak voltage and current stresses on the resonant elements also depend on the same ratio. The LLC-PRC with a filter inductor is examined for two conduction modes, continuous and discontinuous capacitor voltage conduction modes, to show the effect of the inductance ratio. A means to use the derived equations to obtain the zero current switching (ZCS) is given. Also, a design procedure, along with design examples, is given to illustrate the use of the equations and characteristic curves. An experimental LLC-PRC is built to ensure the validity of the equations and design examples     

串联输出DC／DC谐振变换器的稳态分析

分析了高于谐振频率工作的串联输出谐振变换器的工作模式,采用状态变量法计算获得了若干描述稳态工作的特性曲线,为分析和设计这种变换器提供了基础     

Small signal analysis of the LCC-type parallel resonant converter

In this paper, the small signal analysis of the LCC-type parallel resonant converter (LCC-PRC) operating in the continuous conduction mode is given. This analysis is based on both the state-plane diagram, which has been successfully used to obtain the steady state response for resonant converters, and the Taylor series expansion. Applying perturbation directly to the steady state trajectory, a discrete small signal model for the converter can be derived in terns of the input voltage, switching frequency, and the converter state variables. Based on this analysis, closed-loop form solutions for the input-to-output and control-to-output transfer functions are derived. It is shown that the theoretical and computer simulation results are in full agreement     

The effect of the magnetizing inductance on the small-signaldynamics of the isolated Cuk converter

The magnetizing inductance of the isolated Cuk converter introduces an undesirable pair of closely spaced complex zeros and poles, or a glitch, in the control-to-output transfer function. Limited analysis and experimentation in the past have shown that sufficient increase in the magnetizing inductance or manipulation of the ratio of the capacitances of the energy transfer capacitors can reduce the glitch. In this work, the isolated Cuk converter with coupled input and output inductors has been studied and the dependence of the glitch on various circuit parameters has been determined analytically. A condition has been derived for the ratio of the capacitances of the two energy transfer capacitors which completely eliminates the glitch at a given operating point. With this condition satisfied, it is shown that the energy transfer capacitors can be easily damped by a simple RC network to eliminate the glitch from a wide range of operation about an operating point     

Buck modulator with improved large-power bandwidth

A dynamic pulsewidth modulator (DPM) is synthesized to generate a PWM (pulsewidth modulated) signal from dynamic converter variables and from a (quasi-)static control signal. Based on a pragmatic principle with simple hardware implementation, the DPM can be functionally integrated with a PWM converter to broaden the converter power bandwidth, enhancing the converter's ability to meet stringent dynamic specifications. Even if bandwidth broadening is not the prime objective, the smaller phase shift associated with the broader bandwidth simplifies the design of the regulation loop. The DPM principle can also linearize the large-signal behavior of a nonlinear converter. The theory is demonstrated and verified for a buck converter, whose PWM bandwidth is extended from 1/50 of the switching frequency to about 1/3 of the switching frequency.     

腐蚀温度对飞机疲劳寿命的影响

针对飞机在高空飞行环境对飞机结构的疲劳寿命的影响,进行了+50℃～-50℃温度的腐蚀试验研究。共做了3种航空材料（LY12CZ、LC4CZ铝合金和30CrMnSiA合金钢）的腐蚀试验,得到3条腐蚀温度T与腐蚀时间H的特性曲线,说明了临界腐蚀温度的存在,并分析出飞机在-50℃高空腐蚀环境下,腐蚀对飞机机体疲劳寿命基本没有影响。     

Single-phase power-factor-correction AC/DC converters with threePWM control schemes

Three pulse-width modulation (PWM) control schemes for a single-phase power-factor-correction (PFC) AC/DC converter are presented to improve the power quality. A diode bridge with two power switches is employed as a PFC circuit to achieve a high power factor and low line current harmonic distortion. The control schemes are based on look-up tables with hysteresis current controller (HCC) to generate two-level or three-level PWM on the DC side of diode rectifier. Based on the proposed three control schemes, the line current is driven to follow the sinusoidal current command which is in phase with the supply voltage, and two capacitor voltages on the DC bus are controlled to be balanced. The simulation and experimental results of a 1 kW converter with load as well as line voltage variation and shown to verify the proposed control schemes. It is shown that unity PFC is achieved using a simple control circuit and the measured line current harmonics satisfy the IEC 1000-3-2 requirements     

Analysis and design of (LC)(LC)-type series-parallel resonantconverter

A series-parallel resonant converter employing (LC)(LC)-type tank circuit operating in lagging power factor (PF) mode is presented and analyzed using complex ac circuit analysis. Design curves are obtained and the converter is optimized under certain constraints. Detailed Space Integrated Control Experiment (SPICE) simulation results are presented to evaluate the performance of the designed converter under varying load conditions. Results obtained from an experimental converter are also presented. The results obtained from the theory, SPICE simulation, and the experimental converter are compared. The proposed converter has high efficiency from full load to very light load (<10%). Switching frequency variation required for a wide change in the load (near load open circuit to full load) is narrow compared with the series resonant converter (SRC)     

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

Steady-state analysis of the constant-frequency clamped seriesresonant converter

A constant-frequency diode-clamped series resonant converter (CFCSRC) is proposed as a solution to problems associated with frequency-controlled resonant converters. This converter has two resonant frequencies, and control is achieved by varying the relative time spent at each switching frequency. Two zero-current-switching (ZCS) modes are examined and plotted in the output plane. An equation is given for the boundary between the two ZCS modes, as well as an expression for the boundary between ZCS and non-ZCS operation; both are plotted in the output plane. The output equation for the main mode is shown to be hyperbolic. Converter peak voltages limited to the input voltages, and peak currents are less than those of the frequency-controlled clamped series resonant converter over a large operating range. Data from a prototype converter are compared with theoretical data and are shown to be in good agreement with the theoretical model     

Multiple-Tone Signals and Detection Probabillities

An analysis technique is presented for multiple-tone signals insystems employing noncoherent integration of a square-law detectoroutput. It is shown how the characteristic function for the teststatistic can be found from the easily determined "coherent"characteristic function defined in the two-dimensional signal space.This result is applied to two detection problems, the detection of multiple-tone signals in Gaussian noise and the detection of a Gaussian signal in multiple-tone plus Gaussian noise interference.The detection curves are compared to an approximation that is often used in practice to estimate performance. It is found that detection performance in the presence of multiple-tone interferences can be significantly different from that in the presence of Gaussian noise alone.