柔性多层冲击空间碎片防护结构设计与试验

充气展开密封结构是未来空间站以及大型空间居住舱的理想构建形式,其外蒙皮由气密层、增强层、微流星体和空间碎片防护层、辐射保护层以及热控层组成。为了既满足对空间碎片的防护,又满足折叠、收纳以及展开的要求,空间碎片防护层需要采用多层冲击防护结构设计。基于多层冲击防护结构,采用国产的玄武岩纤维材料和芳纶织物的特性参数,根据弹道极限方程设定了柔性空间碎片防护层的设计参数,并通过高速撞击试验对根据设计参数生产的试验件进行了试验验证,试验结果与柔性多层冲击防护结构的弹道极限方程吻合较好。     

航天器微流星体及空间碎片环境与风险分析

微流星体及空间碎片的高速撞击威胁着长寿命、大尺寸航天器的安全运行 ,导致其严重的损伤和灾难性的失效。文章对低地球轨道微流星体及空间碎片环境进行了分析 ,给出了微流星体及空间碎片对航天器威胁方向的确定方法 ,得到了空间碎片撞击航天器相对撞击角的概率分布以及地球对微流星体遮挡的影响。编制了风险分析软件 ,以采用单防护屏防护结构的柱状低地球轨道航天器为例进行风险分析。     

空间碎片超高速碰撞数值模拟的SPH方法

利用光滑质点动力学SPH(Smoothed Particle Hydrodynamics)方法对Whipple防护结构在空间碎片超高速碰撞下的物理过程进行了数值模拟.在数值模拟中,为了充分发挥SPH方法和有限元方法FEM(Finite Element Method)的优点,利用有限元单元和SPH节点混合建模,将有限元单元和SPH节点(SPH nodes)通过定义接触条件相结合,在大变形和飞溅区域采用SPH节点建模,而小变形区域则采用有限元单元建模,从而大大节省求解时间,提高计算效率.计算结果表明,弹丸在穿透前板后,形成二次碎片,碎片云经膨胀和拉长,对后板造成轻微的损伤,这和文献的相关试验数据是符合的.利用SPH方法对空间碎片的超高速碰撞过程进行数值模拟,不仅很好地预测了Whipple防护结构的破坏情况,而且对整个碰撞过程,包括碎片云的形成、膨胀和拉长过程都有形象的描述,符合超高速碰撞的试验测试结果.     

空间碎片预警中的碰撞概率方法研究

由于空间碎片对飞行在地球轨道上的航天器危害日益严重,所以必须采取一些有效的防护措施,对于那些直径大于10 cm的碎片,通常是采用主动规避的方法来进行防护.为了避免传统的Box判据造成的过多错误预警,碰撞概率模型开始被应用于空间碎片预警,本文以空间站为例,将碰撞概率方法与传统Box区域判定法进行比较,介绍碰撞概率计算模型的建立方法,基于位置误差矩阵的碰撞概率Pc的算法,并针对实际交会事例进行了计算和分析.      

天基激光移除空间碎片仿真平台研究与开发

为了从空间碎片和天基移除系统两方面分析激光驱动碎片变轨过程,优化移除任务规划和策略,基于真实的可观测空间碎片数据,设计并开发了一套天基激光移除空间碎片三维数值仿真平台。首先从总体设计出发,对三维数值仿真平台的需求分析、总体框架、模块功能进行了明确的描述。其次通过对激光驱动空间碎片变轨过程数学模型的分析,确定了各模块的具体实现方法。最后采用C++/Qt开发了三维数值仿真平台,通过仿真验证了设计平台的有效性。该仿真平台可用于不同天基平台和目标碎片的任务规划、碎片分布热点区域和航天器防护区域的方案设计及空间环境治理体系的优化设计。     

航天器空间碎片防护方案的评价方法

在综述国际上已采用和研究的航天器防护空间碎片超高速撞击防护方案评价方法的基础上,对航天器防护方案的评价方法进行了分析与探讨,给出了各种防护方案的撞击极限曲线和撞击极限方程。     

基于多项式近似的空间碎片群体轨道预报算法

快速准确地分析空间碎片群轨道演化行为对于其他在轨航天器碰撞规避至关重要。在各摄动力的作用下,空间碎片群演化运动呈现出复杂的非线性特征。空间碎片群体个体数量巨大,如果通过对空间碎片群中每个空间碎片进行轨道积分来分析群体预报的方法会导致计算量过大。针对该问题,提出一种基于多项式近似的轨道快速预报分析方法。该方法将空间碎片群分为少量的标称碎片和其他大量关联碎片。针对标称碎片的轨道预报采用数值积分求解保证预报精度;而针对其他大量的关联碎片轨道预报问题,采用多项式泰勒展开半解析方法求解,从而在保证预报精度的前提下有效减少空间碎片群轨道预报的计算量。为了验证方法的有效性,对不同空间碎片群进行了轨道预报仿真。仿真结果表明,当轨道预报精度设定在1m范围内时,多项式近似算法的计算量较蒙特卡洛方法计算效率提高了2.2~17.2倍,验证了所提出方法的有效性。     

柱状弹丸撞击防护屏形成碎片云材料状态特性研究

微流星体及空间碎片的高速撞击威胁着长寿命、大尺寸航天器的安全运行，导致其严重的损伤和灾难性的失效。为精确估计微流星体及空间碎片高速撞击防护屏所产生碎片云对舱壁的损伤，必须确定碎片云中三种状态材料的特性，建立了碎片云特性分析模型，分别计算了柱状弹丸撞击防护屏所产生碎片云以及碎片云中弹丸和防护屏材料三种状态物质的质量分布。通过计算分析可见，弹丸以不同速度撞击防护屏所产生碎片云三种状态物质的质量分布是不同的，速度增大，液化和气化增强，对靶件的损伤小。而在速度小于7km/s时，碎片云以固体碎片的形式存在，对靶件的损伤大。     

基于模糊应力—强度模型的空间系绳碰撞可靠性

空间系绳系统由于其特殊的组成结构日益受到关注,空间系绳的碰撞可靠性研究是系绳任务设计的重要一环.本文采用可靠性分析基本原理中的应力—强度模型,根据近地轨道的空间碎片通量和泊松分布方法,进行空间系绳在轨碰撞可靠性的研究分析.根据对空间系绳碰撞可靠性有影响的系绳结构因素,即单股系绳的直径、长度,双股系绳的绳间距、碰撞角等,对空间碎片撞击切割系绳后碰撞点处的系绳剩余截面进行建模,利用模糊应力—强度模型计算空间系绳在撞击后发生毁灭性碰撞的概率,进而根据泊松方法计算空间系绳在轨可靠性随时间的变化,通过仿真分析,对比不同结构空间系绳的有效在轨时间.      

空间系绳碎片碰撞生存能力研究

空间系绳结构和几何尺寸对其在复杂空间环境中抵抗碎片碰撞的能力有显著影响.本文根据系绳-碎片碰撞模型和泊松分布,计算了双股系绳和带状系绳被碎片割断的概率,分析了太空碎片对系绳生存能力可能造成的影响.双股系绳是由两条平行系绳每隔一段距离打结连接构成,带状系绳可视为一种横截面为矩形的特殊单股系绳.首先对单股系绳被碎片割断的概率进行建模,然后构建双股系绳和带状系绳生存能力函数,最后根据空间碎片环境模型,对比分析具有不同结构、不同尺寸的系绳的生存能力.仿真结果表明,相较于单股系绳,双股系绳和带状系绳的生存能力有明显提高.      

A space radiation transport method development.

Improved spacecraft shield design requires early entry of radiation constraints into the design process to maximize performance and minimize costs. As a result, we have been investigating high-speed computational procedures to allow shield analysis from the preliminary design concepts to the final design. In particular, we will discuss the progress towards a full three-dimensional and computationally efficient deterministic code for which the current HZETRN evaluates the lowest-order asymptotic term. HZETRN is the first deterministic solution to the Boltzmann equation allowing field mapping within the International Space Station (ISS) in tens of minutes using standard finite element method (FEM) geometry common to engineering design practice enabling development of integrated multidisciplinary design optimization methods. A single ray trace in ISS FEM geometry requires 14 ms and severely limits application of Monte Carlo methods to such engineering models. A potential means of improving the Monte Carlo efficiency in coupling to spacecraft geometry is given in terms of re-configurable computing and could be utilized in the final design as verification of the deterministic method optimized design.     

On the effect of considering more realistic particle shape and mass parameters in MMOD risk assessments

One of the primary mission risks tracked in the development of all spacecraft is that due to micro-meteoroids and orbital debris (MMOD). Both types of particles, especially those larger than 0.1 mm in diameter, contain sufficient kinetic energy due to their combined mass and velocities to cause serious damage to crew members and spacecraft. The process used to assess MMOD risk consists of three elements: environment, damage prediction, and damage tolerance. Orbital debris risk assessments for the Orion vehicle, as well as the Shuttle, Space Station and other satellites use ballistic limit equations (BLEs) that have been developed using high speed impact test data and results from numerical simulations that have used spherical projectiles. However, spheres are not expected to be a common shape for orbital debris; rather, orbital debris fragments might be better represented by other regular or irregular solids. In this paper we examine the general construction of NASA’s current orbital debris (OD) model, explore the potential variations in orbital debris mass and shape that are possible when using particle characteristic length to define particle size (instead of assuming spherical particles), and, considering specifically the Orion vehicle, perform an orbital debris risk sensitivity study taking into account variations in particle mass and shape as noted above. While the results of the work performed for this study are preliminary, they do show that continuing to use aluminum spheres in spacecraft risk assessments could result in an over-design of its MMOD protection systems. In such a case, the spacecraft could be heavier than needed, could cost more than needed, and could cost more to put into orbit than needed. The results obtained in this study also show the need to incorporate effects of mass and shape in mission risk assessment prior to first flight of any spacecraft as well as the need to continue to develop/refine BLEs so that they more accurately reflect the shape and material density variations inherent to the actual debris environment.     

空间碎片环境工程模式参数分析

为了评估空间碎片对航天器造成的危害 ,必须建立空间碎片环境工程模式。文章介绍了空间碎片环境的特点及其工程模式表征方法 ,并比较、分析了几种主要空间碎片环境工程模式的参数 ;从数学建模及风险评估应用的需求出发 ,提出了空间碎片环境工程模式参数的建议方案     

Dust hazard near Halley Comet in case of the VEGA project

The motion of dust particles near Halley Comet is studied and the probability of dust impacts with the spacecraft in case of the VEGA (Venus-Halley)- project is determined. The formation of a crater due to a particle impact with the dust shield is considered and the necessity for using a dual-sheet bumper shield is substantiated. The thickness of a front sheet that plays a role of the particle evaporator is estimated theoretically. The numerical experiment is carried out that simulates the dynamics of collision and evaporation of a particle. Three factors causing perforations of the rear sheet are discussed, i.e. dust penetrated through holes in the front sheet, gas jets and spall fragments of the front-sheet. The consideration of these factors makes it possible to estimate basic parameters of the dual-sheet bumper shield. Flexural vibrations of the front sheet under action of the reverse gaseous jet from the rear sheet are discussed that can affect essentially the shield strength. The perturbing effect of the dust and gas fluxes on the spacecraft is studied.     

Protecting Earth-orbiting spacecraft against micro-meteoroid/orbital debris impact damage using composite structural systems and materials: An overview

Spacecraft that are launched to operate in Earth orbit are susceptible to impacts by meteoroids and pieces of orbital debris (MMOD). The effect of a MMOD particle impact on a spacecraft depends on where the impact occurs, the size, composition, and speed of the impacting object, the function of the impacted system. In order to perform a risk analysis for a particular spacecraft under a specific mission profile, it is important to know whether or not the impacting particle (or its remnants) will exit the rear of an impacted spacecraft wall. A variety of different ballistic limit equations (BLEs) have been developed for many different types of structural wall configurations. BLEs can be used to optimize the design of spacecraft wall parameters so that the resulting configuration is able to withstand the anticipated variety of on-orbit high-speed impact scenarios. While the level of effort exerted in studying the response of metallic multi-wall systems to high speed particle impact is quite substantial, the extent of the effort to study composite material and composite structural systems under similar impact conditions has been much more limited. This paper presents an overview of the activities performed to assess the resiliency of composite structures and materials under high speed projectile impact. The activities reviewed will be those that have been aimed at increasing the level of protection afforded to spacecraft operating in the MMOD environment, and more specifically, on those activities performed to mitigate the mechanical and structural effects of an MMOD impact.     

航天飞行器铸件舱段结构快速设计方法

为提高航天飞行器铸件舱段在方案论证阶段的结构设计效率、设计质量和迭代效率,基于航天飞行器复杂曲面结构特点对铸件舱段结构特征参数进行研究,提出曲线比率法以描述纵筋参数化布局;定义骨架模型发布元素,以实现铸件舱段的Top-Down设计。提出航天飞行器铸件舱段结构快速参数化设计方法,通过定义特征命名规则和创建特征集合实现建模规范化,通过封装舱段设计知识实现设计快速化,通过创建特征参数和公式实现特征参数化。通过建立交互式铸件舱段结构快速设计环境,实现铸件舱段结构的快速实例化、快速修改,并以航天飞行器铸件舱段为例验证了所提方法的可行性和有效性。      

Dynamics and control for contactless interaction between spacecraft and tumbling debris

Tumbling debris has become a great threat to orbit activities. Contactless interaction is a novel concept for active debris removal, through which the tumbling debris no longer rotates freely but is under control. The contactless interaction method aims to de-tumble the debris and then maintain desired relative states between the spacecraft and debris. The spacecraft is simultaneously stabilized through three-axis attitude control, which makes the de-tumbling and capture operation much safer, more effective and accurate. The dynamics and control for the contactless interaction have been little studied in the past years. This paper considers a generic dynamics and control problem for contactless interaction between a spacecraft and debris. A translational and rotational dynamics model of contactless interaction is proposed and the 6-DOF equations are established. The contactless interaction control law is designed with the backstepping method, and the spacecraft three-axis control law is designed with the PD control. Simulation results show that the angular momentum is transferred from the debris to the spacecraft and the debris is thus de-tumbled. The desired relative states are achieved efficiently. Significantly, the spacecraft and debris no longer rotate in the inertial frame and, hence, the safety and accuracy for capture operation are guaranteed.     

中国载人航天工程的外部设计

在“神舟号”载人飞船工程实现了中国人往返于天地间的目的之后 ,中国应审慎地选择发展载人航天的目标。文章从中国社会对载人航天的需求出发 ,讨论了以开发利用空间微重力物质环境为目标的空间站和以发展天基航天为目标的天基航天站的外部工程系统的环境条件 ,认为中国在运载火箭、发射和回收场、测控站网方面已有较好基础 ,基本具备条件 ,运人运输器已有“神舟号”载人飞船 ,运物运输器的研制也不困难 ,但在为保障航天员在空间生活、工作的航天员系统方面和为实现载人航天工程功能和显现价值的有效载荷系统方面欠缺较多 ,需要一个研究、试验、培训和开发、演示的发展阶段     

集群航天器球形边界控制

集群航天器由于其独特的优势,在未来航天任务中将举足轻重,其边界控制也随即成为研究热点.针对近距离伴飞的圆轨道集群航天器,以集群航天器蜂拥控制模型为基础,通过集群航天器球形边界的定义,运用粒子群优化算法,实现了稳定状态下集群航天器的边界参数寻优.采用球形空腔势函数的控制方法,结合集群航天器边界参数反馈信息,实现了对集群航天器球形边界控制,并仿真验证了算法的可行性.     

Assessment of space debris collisions against spacecraft with deorbit devices

Deorbit methods have been employed to remove space debris from orbit. One of these methods is to utilize atmospheric drag. In this method, a membrane loaded into the spacecraft is expanded to increase atmospheric drag. Although this method works without requiring fuel, it has the disadvantage of a high risk of collision with other debris owing to its larger area. Area-time product and energy-to-mass ratio have been used as indices to evaluate the risk of collisions between spacecraft and debris. However, the evaluation criteria were uncertain because these two indices are independent. In this paper, we propose a new evaluation index, single-sheet collision factor (SSCF), that comprehensively evaluates the collision risk based on experiments simulating debris collisions. As a result of the hypervelocity collision experiment, we found that the penetration-area mass of the spacecraft affects the severity of debris collisions. In this paper, the product of the exterior-wall thickness, the exterior-wall density, and the space debris cross-sectional area defines the penetration-area mass of the spacecraft. Furthermore, we compare and evaluate various deorbit methods using SSCF. The comparison showed that the penetration-area mass of the SSCF could be quantitatively determined for the debris-collision severity due to difference in structural materials of spacecraft. SSCF will be used to create rules for space-environment conservation with the expansion of the space-development market.