共查询到20条相似文献,搜索用时 46 毫秒
1.
随机轨道模型在喷管两相流计算中的应用 总被引:1,自引:0,他引:1
应用随机轨道模型对喷管内气-固两相流动进行了数值模拟,结合实验测量结果对使用随机轨道模型和确定轨道模型两种方法的计算结果进行了对比分析,研究了不同固相参数(固相质量比和粒子平均直径)下的固体火箭发动机喷管性能。研究发现,随机轨道模型对实际流动现象的模拟优于确定轨道模型,随着固相质量比和粒子平均直径的增加,喷管两相流损失增加,冲量系数下降。 相似文献
2.
3.
欧阳维真 《桂林航天工业高等专科学校学报》2002,7(1):7-8,11
论文通过对1Cr18Ni9Ti不锈钢试件在-70℃下进行低温拉伸,制备出具有不同形变,诱发α’马氏体相(铁磁相)含量的试样,进行了XRD和TEM研究其相结构。 相似文献
4.
5.
针对中继卫星轨道倾角在一个较大范围内变化,在轨校相采用天线精确指向标校站后,方位向、俯仰向十字拉偏标定校相码的方法,校相时间长,校相过程中轨道漂移带来的星上天线指向变化会影响校相准确性等问题,文章对轨道倾角漂移引起的星上天线指向变化进行仿真,并分析该变化对在轨校相的影响。以此为依据,对中继卫星角跟踪系统在轨校相方案进行研究,给出了粗校准与精校准相结合的校相策略,将轨道倾角漂移引起星上天线指向变化带来的校相误差降至最小。中继卫星角跟踪系统采用该方案进行相位校准后,在天线半功率波束宽度范围内,方位和俯仰误差信号的极性正确,交叉耦合小于20%,多次执行捕获跟踪任务,均能成功捕获跟踪目标,并且自动跟踪精度优于指标要求,验证了相位的正确性,表明该方案切实可行。 相似文献
6.
气压膝关节下肢假肢的分析与研究 总被引:1,自引:0,他引:1
本文应用机构学、生物力学和流体力学等方面的理论,对气压膝关节大腿假肢进行了较为系统的分析和研究.在对实现假肢站立相稳定性和摆动相控制性分析的基础上,用平面多杆机构模拟大腿假肢的多中心膝机构,建立了该机构的力学模型,并进行了最优化方法设计;根据正常人体的步态数据,用气压控制装置来模拟假肢摆动相控制性,并达到良好效果;最后进行了假肢膝关节的结构设计. 相似文献
7.
引言开关控制系统是典型的非线性系统,当其线性部分不高于二阶时,可用相平面法进行分析.导弹和运载器上使用的喷管开关姿态控制系统,如果忽略晃动,并经简化后,线性系统可以看作二阶的,很适宜使用相平面分析和设计. 本文论述这种相平面分析法,得出了相轨迹和极限环的重要公式和结论,对选择系统参数有实用价值. 相似文献
8.
9.
10.
11.
介绍了一种新的刚体转动的四元数模型。这些模型可以提高再定向控制的对边界条件的适应能力,在此基础上还介绍了这些模型的一些实际应用。 相似文献
12.
A. A. Davydov 《Cosmic Research》2011,49(4):335-344
A communication satellite (small spacecraft) injected into a geosynchronous orbit is considered. Flywheel engines are used
to control the rotational spacecraft motion. The spacecraft after the emergency situation has passed into a state of uncontrolled
rotation. In this case, no direct telemetric information about parameters of its rotational motion was accessible. As a result,
the problem arose to determine the rotational satellite motion according to the available indirect information: current taken
from the solar panels. Telemetric measurements of solar panel current obtained on the time interval of a few hours were simultaneously
processed by the least squares method integrating the equations of rotational satellite motion. We present the results of
processing 10 intervals of the measurement data allowing one to determine the real rotational spacecraft motion and to estimate
the total angular momentum of flywheel engines. 相似文献
13.
The problem of optimal control over many-revolution spacecraft orbit transfers between circular coplanar orbits of satellites is considered. The spacecraft flight is controlled by a thrust vector of a jet engine with restricted thrust (JERT). The mass expenditure is minimized at a limited time of flight. The optimal control problem is solved based on the maximum principle. The boundary value problem of the maximum principle is solved numerically using the shooting method. A modified computation scheme of the shooting method is suggested (multi-point shooting), as well as a method (correlated with the scheme) of choosing the initial approximation with the use of a solution to the optimization problem in the impulse formulation. The scheme and method allow one to construct many-revolution spacecraft orbit transfers. 相似文献
14.
热变形对天线指向机构的指向精度具有重要影响,但利用传统的设计方法很难实现对指向精度的准确计算,尤其是热变形对指向精度影响的研究工作更是少见。为此建立了机构的三维实体热-结构耦合有限元分析模型,根据有限元分析结果并结合机构的运动链关系,构建了各关键运动副运动误差的计算方法;在此基础上实现了机构指向误差的计算,研究了运动副名义、最大以及最小配合间隙条件下,温度载荷对各关键运动副运动误差和指向精度的影响。研究结果表明,温度载荷对关键运动副的运动误差以及机构的指向精度具有重要影响,随着温度载荷偏离常温数值的增加,指向误差不断增大,名义配合间隙条件下的指向误差最大。 相似文献
15.
16.
17.
18.
金属网由于柔韧性好、使用方便等优势而在电缆屏蔽工程上得到广泛应用。本文对电缆用的金属网屏蔽效能进行工程计算,通过计算,对金属网不同材料、不同规格、单层与双层屏蔽及有缝隙情况下的屏蔽效能进行比较与分析,对工程应用有一定的指导意义。 相似文献
19.
为满足航天器微振动环境模拟的需要,开展了多自由度微振动时域波形复现控制方法研究。首先,介绍了基于时域波形复现的多自由度微振动环境模拟控制理论方法。其次,针对六自由度微振动激励系统,应用MATLAB软件建立了基于实测传递函数矩阵的多输入多输出微振动激励仿真系统,针对微振动时域波形复现闭环控制过程进行了算法编程,并给出了仿真的闭环控制流程图。最后,通过算例对多自由度微振动时域波形复现进行了数值仿真,以给定的白噪声为输入,模拟对实际存在的系统非线性、测量误差等影响因素的控制效果。仿真结果验证了多自由度微振动时域波形复现控制方法的可行性及有效性,所得结论可以为研究多自由度微振动时域波形复现控制系统提供参考。 相似文献
20.
The problem of determining an estimation of current spacecraft motion parameters on the stage of its descent is solved on the basis of readings of an optoelectronic navigation system and additional information from the self-contained inertial navigation system at the most general assumptions on the nature of motion of the object and the statistical properties of the noise of the measuring devices. 相似文献