C/C 复合材料的高温抗氧化防护研究进展

C/ C 复合材料在高温有氧环境中易氧化的缺点一定程度上影响了它在航空航天领域的应用与推
广,抗氧化涂层技术是提高其高温长时间抗氧化性能最直接有效的方法。本文综述了近年来国内外C/ C 复合
材料高温抗氧化涂层在玻璃、贵金属、陶瓷等涂层体系方面的最新研究成果;在分析介绍C/ C 高温抗氧化涂层
传统制备工艺优缺点及应用情况的基础上,进一步总结了高温抗氧化涂层制备技术最新研究进展;并对已开发
的抗氧化涂层体系适用环境及应用现状进行了深入的评述。最后针对C/ C 复合材料1 800℃以上的超高温抗
氧化防护问题,指出了目前研究中存在的问题及未来应重点努力发展的方向。     

SiO2 改性ZrO2 气凝胶高温稳定性

以ZrOCl2·8H2O 为锆源,以环氧丙烷( PO) 为凝胶促进剂制备ZrO2 凝胶,将ZrO2 凝胶置于正硅
酸乙酯乙醇溶液中老化,再结合高温超临界干燥工艺制备了SiO2 改性ZrO2 气凝胶。通过对比ZrO2 气凝胶和
SiO2 改性ZrO2 气凝胶高温结构转变讨论了SiO2 改性对ZrO2 气凝胶高温结构的影响。采用FT-IR、XRD、SEM
和TEM 等分析手段对样品进行高温结构表征。结果表明:采用正硅酸乙酯乙醇溶液老化ZrO2 凝胶后,在ZrO2
凝胶粒子表面形成了一层SiO2 包裹层,这层SiO2 包裹层显著抑制了ZrO2 的扩散、成核和生长过程,高温稳定
性得以显著提高。     

7501 氰酸酯树脂及其复合材料性能

研究了7501 氰酸酯树脂的工艺和耐热性能,以EW220 布为增强材料,采用RTM 成型工艺制备
了EW220/7501 复合材料层板,研究了其室温和高温力学性能。结果表明:7501 氰酸酯树脂的最低黏度为87
mPa·s,开放期大于10 h,300℃固化后,热分解温度为431℃,Tg 可达421℃;EW220/7501 复合材料室温下具有
良好的力学性能,其中拉伸强度为393 MPa,压缩强度为356 MPa,弯曲强度为602 MPa,层间剪切强度为43
MPa,在300℃下,各项力学性能保持率均≥80%。     

国产芳纶纤维复合材料用环氧树脂体系

研制了一种环氧/ 芳香胺体系,采用DSC、固化反应动力学分析等方法对树脂体系进行了表征,并
对其浇注体、复合材料NOL 环以及Φ150 mm 压力容器性能进行了研究。结果表明,该树脂体系具有优良的浇
注体力学及热性能,其拉伸强度为101 MPa,断裂伸长率达4. 1%,弯曲强度为177 MPa,马丁耐热温度为
142． 2℃;与国产芳纶纤维的界面粘接性能良好,其NOL 环层间剪切强度可以达到52. 1 MPa,制备的复合材料
Φ150 mm 压力容器PV / W 值可达38. 44 km。     

高导热C/ C 复合材料的发展现状

高导热C/ C 复合材料具有高热导率、低密度、低热胀系数和高温下高强度等性能,成为近年来最
具发展前景的散热材料之一。本文综述了国内外高导热C/ C 复合材料的发展现状,分析了C/ C 复合材料的热
物理性能及影响其热导率的因素,介绍了C/ C 复合材料的导热机理、碳纤维、基体炭的导热性能,以及高导热
C/ C 复合材料的制备和改性等。     

MAX 相陶瓷的制备、结构、性能及发展趋势

介绍了三元层状可加工陶瓷MAX 相的结构特征、制备方法,室温和高温力学性能, 探讨了提高
高温力学性能和抗氧化性能的方法,并提出了该类陶瓷的应用前景和发展方向。     

考虑气体扩散渗透的隔热材料瞬态隔热性能数值模拟

高超声速飞行器机动飞行时环境压力变化导致隔热材料沿厚度方向存在压力梯度,进而引起隔
热材料内气体的扩散渗透,影响隔热材料隔热性能。为研究气体扩散渗透对隔热材料隔热性能的影响,建立了
隔热材料内气体扩散渗透模型,采用罗斯兰德近似、有限体积法建立了隔热材料内扩散渗透及辐射导热传热计
算模型,对气体扩散渗透条件下的瞬态隔热性能进行了数值模拟。算例模拟结果表明:对2 cm 厚纳米隔热材
料,在外界气压为0. 1 MPa,绝热面为真空的状况下,当渗透率大于10-14 m2 时,气体扩散渗透开始影响隔热材
料内传热,导致隔热性能降低,气体黏性系数对气体扩散渗透有显著影响,随着黏性系数降低,气体扩散渗流现
象显著;衰减系数对绝热面温度响应有显著影响,随着衰减系数增大,绝热面温度响应显著降低。     

Re/ Ir 高温抗氧化性能

采用电弧离子镀技术在Re 金属表面制备Ir 涂层,研究沉积态Ir 涂层的微观形貌、成分和相结构
以及在不同温度区域的高温抗氧化性能。通过分析表明,利用电弧离子镀方法,可以在Re 金属基体表面制备
出连续、致密和均匀的Ir 涂层。Re/ Ir 试样的抗氧化寿命,1 800℃可达到4 h;2 000℃可达到2 h。在1 950℃
条件下,进行120 次热震试验,试验后Ir 涂层表面光滑致密,表面没有发现任何剥离现象。     

玻璃布增强PPBES/ PPENK 树脂基层压板的研究

将含二氮杂萘酮结构、耐高温可溶解的聚芳醚砜(PPBES) 与聚芳醚腈酮(PPENK) 共混,采用溶
液浸渍法制备了玻璃布增强PPBES/ PPENK 树脂基层压板。讨论了树脂的相容性及树脂配比,研究了共混树
脂含量对PPBES/ PPENK 层压板的室温及150℃弯曲强度、吸水率的影响,对层压板的介电性能、阻燃性能等
进行了测试。结果表明:PPBES 与PPENK 完全相容。当PPBES/ PPENK = 4/6( 质量比),树脂质量分数为
35． 4%时,层压板的综合性能最佳,且150℃的弯曲强度保持率为95. 7%。在1 MHz 下,介电常数为3. 5,tanδ
为0. 0037;在DC 500 V 下,体积电阻率为5. 9×1014Ω·cm;阻燃性能达到V-0 级。     

表面粗糙度对高辐射涂层发射率的影响

以氧化铁、碳化硅和氧化钴为高辐射填料,通过控制涂层浆料固含量和喷涂次数制备出了不同表
面粗糙度的高辐射涂层。用AE 辐射计测试了不同表面粗糙度高辐射涂层的室温发射率,根据GB/ T 7287—
2008 测试了涂层的800℃高温发射率,用扫描电子显微镜和光学显微镜观察了涂层表面形貌,用扫描探针显微
镜测试了涂层的表面粗糙度。结果表明,在辐射换热条件下高辐射涂层表面粗糙度在2. 75 ~225. 70 μm 变化
时,其室温发射率发生了0. 02 ~ 0. 05 的变化。而在导热换热条件下高辐射涂层表面粗糙度在2. 75 ~ 36. 99
μm 变化时,其高温发射率没有变化。     

有翼高超声速再入飞行器气动设计难点问题

有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。     

Simulation and Analysis of Crashworthiness of Fuel Tank for Helicopters

Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

突破技术趋同，波音再现竞争优势

 波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面：电子化（e-Enabled）运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境（GCE）。     

临近空间飞行器测控与信息传输系统频段选择

 临近空间飞行器是高性能信息化武器平台,测控（TT&;C）与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联（ITU）国际标准、高速数传、接收信噪比（SNR）、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。     

基于弯曲激波压缩系统的高超声速进气道反设计研究进展

总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。     

Experimental Study on Effects of Fuel Injection on Scramjet Combustor Performance

In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances.     

(高)超声速流动试验技术及研究进展

近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。     

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.