共查询到20条相似文献,搜索用时 62 毫秒
1.
2.
阐述了等效系统的基本概念,介绍了高增益飞机荷兰滚模态特性的试飞方法以及采用等效系统拟配的方法计算其模态特性指标。结合某型飞机具体算例,给出了该飞机频域拟配的结果和飞行品质指标图。结果满足国军标对飞行品质的一级要求,表明该计算方法正确,结果可靠。 相似文献
3.
4.
本文介绍了飞机飞行颤振试验的简况、颤振试飞数据处理的特点和一些特殊要求。简要介绍了用频域参数识别方法和时域参数识别方法识别模态频率和阻尼的基本原理和基本数学模型。文中着重介绍了为解决颤振试飞中所获得的信号的信噪比差,而又要求识别的模态阻尼值的精度比较高这个矛盾和为了尽量缩短数据分析所花费的计算时间而采取的若干措施。 相似文献
5.
Flight Flutter Modal Parameters Identification with Atmospheric Turbulence Excitation Based on Wavelet Transformation 总被引:2,自引:0,他引:2
Zhang Bo Shi Zhongke Li Jianjun 《中国航空学报》2007,20(5):394-401
针对基于大气紊流激励的飞机颤振试验数据具有信噪比低以及测量数据以加速度响应形式给出等特点,将小波变换与随机减量法相结合对飞机颤振模态参数进行识别,首先利用随机减量法获得结构在非零初始加速度条件下的自由衰减响应,然后对该自由衰减响应进行Morlet连续小波变换,为使变换简单,本文采用了Parseval定理和留数定理,利用Morlet的带通滤波特性,通过搜索小波变换系数在不同的尺度区域内的极大值,再根据小波变换系数的极大值、相角与固有振动频率及阻尼系数间的关系,即可识别出各模态参数。并对利用小波变换识别颤振模态参数时,实现模态解耦应满足的条件进行了分析研究。通过仿真和飞机颤振试验数据分析,验证了该识别方法不仅简单、有效和可行,而且具有较强的抗噪性。 相似文献
6.
7.
阐述了颤振激励系统(FES)在现代飞机飞行试验中的重要性,论述了FES研制的历史背景。FES作为一种新型的颤振激励系统,在完成了软/硬件设计之后,进行了大量的验证试验。FES是通过电传飞控系统去激励飞机响应,为将风险减少到最小程度,在全权限全时数字变稳电传操纵系统的空中飞行模拟机上进行了验证试飞,而后在某型飞机上进行了验证试飞并投入实际使用,结果表明,FES的监控保安电路可靠,与飞控交联匹配,隔离措施有效,满足飞控稳定裕度以及气动伺服弹性,颤振和操稳等科目的试飞要求。 相似文献
8.
F—16飞机在非对称外挂情况下的极限环振荡试验 总被引:1,自引:0,他引:1
空军猎鹰办公室(AFSEO)提出了F-16飞机非对称外挂构型的验证要求。根据模拟构型的试飞和分析结果进行了F-16飞机的颤振验证。历史上,几乎没有对非对称构型提出过要求,因此,F-16飞机在非对称影响下的颤振特性试飞数据是有限的。结合这个问题,AFSEO以前仅用半展动力学和气动力模型进行计算,而假定在另一侧为镜面效应。为了解是否所有的非对称构型都必须用全展模型来分析,他们制定了一个试验大纲。用半展和全展模型对各种非对称构型下的颤振特性进行了分析。全展模型分析结果表明该机有颤振不稳定性,这与半展模型分析结果不同,因而进行了颤振试飞。试飞结果表明非对称构型的加载会产生一个较大的灵敏度,同时还会增加其稳定性。试飞结果与全展的气动模型吻合得相当好,这表明对于非对称的载荷构型应该使用全展气动模型进行分析。 相似文献
9.
10.
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:2,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
13.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
14.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
15.
16.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
17.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
18.
Integrated Entry Guidance for Reusable Launch Vehicle 总被引:2,自引:2,他引:0
NING Guo-dong ZHANG Shu-guang FANG Zhen-ping 《中国航空学报》2007,20(1):1-8
A method for the implementation of integrated three-degree-of-freedom constrained entry guidance for reusable launch vehicle is presented. Given any feasible entry conditions, terminal area energy management interface conditions, and the reference trajectory generated onboard then, the method can generate a longitudinal guidance profile rapidly, featuring linear quadratic regular method and a proportional-integral-derivative tracking law with time-varying gains, which satisfies all the entry corridor constraints and meets the requirements with high precision. Afterwards, by utilizing special features of crossrange parameter, establishing bank-reversal corridor, and determining bank-reversals according to dynamically adjusted method, the algorithm enables the lateral entry guidance system to fly a wide range of missions and provides reliable and good performance in the presence of significant aerodynamic modeling uncertainty. Fast trajectory guidance profiles and simulations with a reusable launch vehicle model for various missions and aerodynamic uncertain-ties are presented to demonstrate the capacity and reliability of this method. 相似文献
19.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
20.
(高)超声速流动试验技术及研究进展 总被引:1,自引:1,他引:1
近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。 相似文献