共查询到20条相似文献,搜索用时 700 毫秒
1.
2.
基于成形磨削的几何原理和机床运动学原理,提出了斜齿轮副的一种分段拓扑修形方法.通过改变齿顶和齿根处渐开线的发生线长度实现齿廓分段修形;给砂轮附加一个抛物线+直线的径向进给运动实现齿向分段修形.推导出基于成形磨削过程中拓扑修形齿面的计算公式,对修形齿面的边界进行了划分,建立成形磨齿机各伺服轴的运动方程.根据齿面的数值模拟结果,在五轴数控(CNC)成形磨齿机上进行磨削加工与在机拓扑测量,验证了成形法实现齿面拓扑修形的可行性. 对给定转速和负载工况下的齿轮箱进行加载试验,齿轮箱振动能量级幅值下降0.008dB,噪声减小约2dB.研究表明分段拓扑修形有利于降低齿轮传动振动和噪声. 相似文献
3.
根据长期工作实践经验,总结了圆柱齿轮磨齿机床主要类型、各自加工原理及主要特点,并对其发展趋势进行了分析和论述,指出成形磨以其明显技术优势,将在今后一个时期内成为高科技齿轮加工的主要工艺方法。 相似文献
4.
针对内斜齿轮数控成形磨削中较难解决的磨削干涉问题,研究了内斜齿轮成形磨削的砂轮修形方法.在建立内斜齿轮成形磨削数学模型的基础上,用截圆法得到磨削内斜齿轮时砂轮与齿槽接触点所满足的条件方程组,通过牛顿迭代法解此方程组求出砂轮廓形.用数值法模拟出所求砂轮的实际磨削齿形并与理论渐开线齿形作比较,以检验磨削是否干涉及砂轮半径和安装角的选取是否正确.基于 Visual C++ 6.0 编制内斜齿轮砂轮修形及误差分析软件,通过仿真正确选择砂轮安装角、砂轮半径,并输出数控砂轮修整程序.最后通过磨削和检测实例,验证了理论的正确性和软件的可行性. 相似文献
5.
6.
7.
8.
提出了利用现有球形滚刀与改造滚齿机加工面齿轮的方案。推导了球形滚刀基本蜗杆螺旋面方程,建立了滚切面齿轮的坐标系统。通过对成形误差曲面的研究发现用现有球形滚刀加工面齿轮的理论造形误差很小,且远小于插齿成形误差。轮齿接触分析表明滚切得到的面齿轮与标准圆柱齿轮啮合轨迹的位置及方向与理论啮合轨迹基本一致,而滚切得到的面齿轮副传动误差为有利的抛物线形。该文的研究为面齿轮的加工找到了新方法,并为球形滚刀开辟了新用途。 相似文献
9.
渐开线碟形砂轮磨削面齿轮数控加工研究 总被引:1,自引:0,他引:1
为进行面齿轮数控精密加工,提出了一种渐开线碟形砂轮磨削面齿轮加工方法.根据面齿轮成形过程及磨削加工原理,推导了渐开线碟形砂轮磨削面齿轮齿面方程,进行了面齿轮磨削加工机床设计,给出了基于机床结构的面齿轮磨削加工方法,进行了磨削加工过程中的啮合点刀位计算;借助VERICUT软件进行了面齿轮数控磨削加工仿真,最后进行了面齿轮磨削加工试验,通过对面齿轮齿面进行检测,得到齿面偏差最大值为-10.1~12.1μm,结果验证了渐开线碟形砂轮磨削加工面齿轮方法的正确性. 相似文献
10.
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:2,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
13.
基于飞机油箱模型形状特征油量测量切片步长选择方法研究 总被引:1,自引:0,他引:1
在分析飞机数字式油量测量过程中目前广泛使用的切片法油量测量原理的基础上,针对现有的定步长切片法无法得到准确、可靠的燃油质量特性数据库的缺陷,结合对飞机油箱模型形状特征的分析,提出了基于飞机油箱模型形状特征的油量测量切片步长选择方法。此方法包括切片步长整体和局部选择两个过程,整体选择以实现相邻两切片平面所夹油箱模型体积近似相等为目的来确定切片步长,以体现油箱模型截面整体变化规律;局部选择以设计切片平面与截面突变平面重合或尽可能接近的方式,突出油箱截面的局部变化特征。实验结果表明:该切片步长选择方法较定步长方法能够建立更为合理、可靠的燃油质量特性数据库,从而提高了油量测量精度。 相似文献
14.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
15.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
16.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
17.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
18.
19.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
20.
Abnormal Shape Mould Winding 总被引:1,自引:0,他引:1
Fu Hongya Wang Xianfeng Han Zhenyu Fu Yunzhong 《中国航空学报》2007,20(6):552-558
为解决网格化芯模的缠绕问题,本文提出了复合材料面片缠绕机理;接着详细分析了面片缠绕过程中的芯模凹曲面上纤维滑线和架空现象,应用微分几何曲面理论和空间几何理论,提出判据及其解决方案;最后,针对飞机发动机进气道的缠绕成型,编制缠绕控制程序并进行相应的实验,验证了面片缠绕方法的可行性。 相似文献