摩托车电控点火提前角实时推定算法研究(2)

发动机电控点火系统需要实时检测与最佳点火提前角相应的曲轴转角。实际发动机如采用一个曲轴转角传感器,就必须采用数值预测方法。采用集相平均和时间平均法外推预测曲轴转角,并将计算值与试验值进行了比较。结果表明:低速下采用时间平均法,高速下采用集相平均法,即可满足控制精度的要求,也可以减轻系统的实时性要求。采用线性计算方法足可以满足±0.5°曲轴转角精度的要求,同时计算简单,更适宜资源紧张的单片机采用。     

摩托车发动机点火提前角的研究

与汽车相比，摩托车发动机的未燃HC排放较高。减少未燃HC排放的有效措施就是控制点火提前角。本文对我国目前摩托车发动机点火系统的点火特性及对发动机动力性、经济性及排放性能的影响进行了分析，讨论了固定式点火系统及目前最广泛使用的CDI点火系统的不足，兼顾性能及成本，指出了升级现有点火系统的思路及所需要做的工作。     

基于凹腔火焰稳定器的亚燃冲压发动机点火性能研究

通过碳氢燃料亚燃冲压发动机直连式试验,对凹腔火焰稳定器的点火性能进行了初步研究.试验分别在高能火花塞及氰气引导火焰两种情况下成功实现了可靠点火.结果表明,基于凹腔火焰稳定技术的亚燃冲压发动机的点火性能与燃料喷注压降及喷注方式密切相关.在壁面喷注燃料的方式下,发动机容易实现可靠点火,而在中心喷注燃料的情况下,发动机很难被点燃.此外,试验还发现,发动机的喉部尺寸对采用这类结构的哑燃冲压发动机凹腔内的压力影响较小,因此,喉部尺寸的变化对其点火性能的影响也较小.     

含纳米金属粉的推进剂点火实验及燃烧性能研究

利用CO2激光点火系统对含有纳米铝粉和纳米镍粉的AP／HTPB推进剂进行激光点火实验,测量了推进剂在不同激光功率和压强下的点火延迟时间,对推进剂的燃速、常压点火温度和爆热也进行了测量。同时,利用氧化还原滴定法测定燃烧残渣中活性铝含量。结果表明,纳米铝粉(n—Al)的点火阀值比普通铝粉(g-A1)的点火阀值小几个数量级,加入纳米铝粉可有效地缩短推进剂点火延迟时间。而在纳米镍粉为催化剂的协同作用下,推进剂燃速明显提高,点火延迟时间也大大减少,Al在推进剂燃烧过程中的燃烧效率得以提高,同时燃烧残渣中活性铝含量也明显降低。     

固体燃料超燃冲压发动机原理性试验研究

进行了固体燃料超燃冲压发动机实验研究,并成功进行了点火和燃烧实验,包括固体碳氢燃料超音速燃烧试验和聚甲基丙烯酸甲酯(PMMA)超音速燃烧试验。实验验证了固体燃料在超音速气流中能可靠点火,并保持了火焰的稳定燃烧,获得了固体燃料的超音速燃烧内弹道特性,同时研究了固体燃料PMMA在超音速气流中的燃烧,分析了其在超燃冲压燃烧室内的退移规律,认为燃料退移速度随时间变化,燃烧趋向于将燃面轮廓变平,区域显示圆柱形。     

H_2O_2/HTPB缩比固液火箭发动机药柱燃速试验研究

对采用90%H2O2/HTPB基推进剂组合的缩比固液火箭发动机开展了药柱燃速试验研究,得到了不同点火方式和不同氧化剂流率下的药柱燃速。试验结果表明,在相同的氧化剂流率下,催化点火方式比点火药点火方式药柱燃速要高,燃烧室压力更为平稳,同时建压时间要长。根据点火药点火方式下不同氧化剂流率的药柱燃速拟合得到了燃速公式,并运用燃速公式对300 mm全尺寸发动机进行了装药设计及内弹道性能计算,得到的理论性能曲线与试验结果吻合很好,验证了本文采用的燃速研究方法及结果。     

多孔药柱燃气发生器的燃速变化和重现性

研完了多孔药柱燃气发生器的燃速变化特性。对几种装药量为0.5～150kg、有19～235个平行圆孔的药柱的设计进行了评价。主要讨论了多孔药柱与通常的中孔内部燃烧药柱燃速变化曲线的形状和大小的差别,不同的多孔药柱之间的差别,这些效应与弹道预测的关系,多孔药柱的压力一时间曲线重现性分析。分析采用了燃速和燃面的点火前及点火后的弹道性能评估,也考虑了侵蚀燃烧、侵蚀和沉积引起的喉面变化及特性速度变化的影响。从多孔药柱燃气发生器的点火后分析,推导出多孔药柱一般燃速变化曲线,使性能预测精度提高达3%。多孔药柱燃气发生器的性能重现性很好。高燃速发生器最大压力偏差小于3%,低燃速发生器最大压力偏差小于5%。     

终端末制导中的轨控直接力点火策略

为了提高命中精度,高层大气中防空导弹的终端末制导段常采用轨控直接力实现快响应。在固定的直接力模式下,轨控的点火时间和点火方位直接决定命中精度。目前,常用的点火逻辑由于对预测脱靶量和点火方位估计精度较低使得直接力修正效果未能充分发挥。为此,从3个层面进行点火策略的改进。首先,针对终端末制导过程视线发散的固有特点,通过引入视线角速率变化趋势,提高预测脱靶量估计精度;其次,考虑直接力装置有限的工作时间,通过增加剩余速度修正项,改善直接力修正能力估计精度;第三,将原有基于视线角速率的点火方位策略改进为基于剩余需用过载方向。理论分析表明,相比现有方法,文中提出的改进策略可适当提前点火时间。用不同的机动目标进行六自由度仿真验证,结果表明,新的策略在目标大机动下,可显著降低脱靶量;在小机动下,其性能与原方法相当。     

固体燃料超燃冲压发动机关键基础技术问题

针对固体燃料超燃冲压发动机的应用背景、技术优势和发展需求,对制约固体燃料超燃冲压发动机进一步工程化应用所面临的主要关键基础技术进行系统梳理。通过对固体燃料超燃冲压发动机工作原理、点火和火焰稳定性、燃面退移速率模型、固体燃料种类、超燃冲压发动机试验台技术特点及固体燃料超燃冲压发动机工作性能的阐述,详细分析了固体燃料超燃冲压发动机技术研究的进展和难点,并对固体燃料超燃冲压发动机未来研究趋势进行了展望。研究认为,固体燃料在超声速流动下的细化燃烧反应机理还需要进行深入研究,需要建立更加完善的超声速细化燃烧模型;考虑不同的固体燃料,固体燃料配方不同,带来推力性能和燃烧效率也不一样,需要推动固体推进剂技术改良;发动机地面试验测量方式过于单一,需要发展先进的测量手段。     

富氧预燃室初步试验研究

为了研究全流量补燃循环发动机中富氧预燃室的点火以及燃烧特性，对点火方案和预燃室方案进行了分析。通过对多种预燃室结构形式和点火方式的比较，提出了适合于富氧预燃室初步试验要求的点火方案，研制了热表面谐振点火器并采用间接点火方式研制了氢氧火炬点火器。点火器的试验结果表明氢氧火炬点火器能够多次可靠地点火并生成稳定的点火火炬。由于不受谐振产生条件的限制，氢气和氧气的流量和混合比可以在较大的范围内选择，生成点火火炬的温度范围也很宽。对确定的富氧预燃室方案进行了设计加工，经过三个阶段的热试车，富氧预燃室的关键参数均达到了设计要求，结构无烧蚀，工作可靠，完全可以满足全流量补燃循环发动机系统对富氧预燃室的要求。     

On the stability of the track of the space elevator

A string moving with geostationary angular velocity in its radial relative equilibrium configuration around the Earth, reaching from the surface of the Earth far beyond the geostationary height, could be used as track for an Earth to space elevator. This is an old dream of mankind, originating about 100 years ago in Russia. Besides the question of feasibility from a technological point of view also the question concerning the stability of such a configuration has not yet been completely solved. Under the assumption that a proper material (carbon nanotubes) is available, making the connection possible technologically, we address the question of existence and stability of the radial relative equilibrium of a tapered string on a circular geosynchronous trajectory around the Earth, reaching from the surface of the Earth far beyond the geostationary height.     

On the Possibility of the Existence of Volatile Compounds in the Region of the Scott Crater on the Moon

In this paper, we analyze the illumination conditions, the thermal regime, and the possibility of deposits of volatile compounds existing in the vicinity region (NSR S5 region) near the southern pole of the Moon. It has been found that there are no permanently shadowed zones near the Scott crater and the NSR S5 region, though the temperature conditions allow the of compounds such as CH₃OH, SO₂, NH₃, CO₂, H₂S, C₂H₄, and water to remain stable relative to evaporation for a long time (≥1 Gyr). It has been also shown that compounds like CO and CH₄ cannot stably exist in these regions.     

对老年人体育锻炼负荷量监控方法的探讨

通过对老年人体育锻炼活动的情况进行相关调查，发现目前老年人体育锻炼中存在一些误区。因此本文针对这些现实情况提出，应根据实际情况运用一些简单易行的方法来对老年人体育锻炼实施医务监督，达到提高老年人体育锻炼的科学性。     

Estimation of the current density and analysis of the geometry of the current system surrounding the Earth

The results of an investigation of the distribution of plasma pressure, pressure gradients, and magnetic field near the equatorial plane in the plasma ring surrounding the Earth under magneto-quiet conditions are presented. Observational data obtained during the international THEMIS mission are used. The picture of the distribution of transverse-current density near the equatorial plane was obtained under assumption of observing the magnetostatic balance condition at geocentric distances from 6 to 12R _E. In estimating the integral transverse current it was accepted that in daytime sector the magnetic-field minima on magnetic field lines are not localized in the equatorial plane. Estimates of the integral transverse current were obtained, which demonstrate the possibility of closing nighttime transverse currents at geocentric distances of up to ～12R _E inside the magnetosphere, which form a high-latitudinal continuation of the ring current.     

实施“三位一体”教育模式 提高学生的综合素质

本文介绍了“三位一体”教育模式的内容,描述亍我们实施该模式所采取的措施及取得的成效。实践表明,“三位一体”教育模式能够提高学生的综合素质,为学生毕业后的发展打下坚实基础,对教育模式的改革具有一定的指导意义。     

Estimating the accuracy of the technique of reconstructing the rotational motion of a satellite based on the measurements of its angular velocity and the magnetic field of the Earth

The paper has studied the accuracy of the technique that allows the rotational motion of the Earth artificial satellites (AES) to be reconstructed based on the data of onboard measurements of angular velocity vectors and the strength of the Earth magnetic field (EMF). The technique is based on kinematic equations of the rotational motion of a rigid body. Both types of measurement data collected over some time interval have been processed jointly. The angular velocity measurements have been approximated using convenient formulas, which are substituted into the kinematic differential equations for the quaternion that specifies the transition from the body-fixed coordinate system of a satellite to the inertial coordinate system. Thus obtained equations represent a kinematic model of the rotational motion of a satellite. The solution of these equations, which approximate real motion, has been found by the least-square method from the condition of best fitting between the data of measurements of the EMF strength vector and its calculated values. The accuracy of the technique has been estimated by processing the data obtained from the board of the service module of the International Space Station (ISS). The reconstruction of station motion using the aforementioned technique has been compared with the telemetry data on the actual motion of the station. The technique has allowed us to reconstruct the station motion in the orbital orientation mode with a maximum error less than 0.6° and the turns with a maximal error of less than 1.2°.     

Optimization of the trajectory of the spacecraft insertion into the system of heliocentric orbits

The possibility of the spacecraft insertion into the system of operational heliocentric orbits has been analyzed. It has been proposed to use a system of several operational heliocentric orbits. On each orbit, the spacecraft makes one or more revolutions around the Sun. These orbits are characterized by a relatively small perihelion radius and relatively high inclination, which allows one to investigate the polar regions of the Sun. The transition of the spacecraft from one orbit to another has been performed using an unpowered gravity assist maneuver near Venus and does not require the cruise propulsion operation. Each maneuver transfers the spacecraft into the sequence of operational heliocentric orbits. We have analyzed several systems of operational heliocentric orbits into which the spacecraft can be inserted by means of the considered transportation system with electric propulsion (EP). The mass of the spacecraft delivered to these systems of operational orbits has been estimated.     

从应变计现状看电阻式传感器的前景

电阻式传感器的核心部件——电阻应变计是目前最常用的应力分析的敏感元件。也常用于测量力、压力、扭矩和加速度等物理量。作者简要回顾了电阻应变计的发展历史，介绍了电阻应变计的结构、分类及现状，展望了电阻式传感器的前景。     

System of works on numerical modeling of the dynamics of the structure of the Space Radiotelescope in the RadioAstron project

The results of modeling the dynamics of the Space Radiotelescope are presented. The results of ground-based vibration-dynamic tests are used to validate the calculation models and estimate the damping levels. The dynamic distortions of the reflecting surface caused by the operation of the pointing mechanism of the high-gain antenna are estimated.     

复杂受载条件下固体火箭发动机壳体屈曲应力的估计

论文简略介绍了静力轴压下园柱壳屈曲应力的工程计算方法,对某固体火箭发动机壳体的复杂受载条件对壳体屈曲应力的影响进行了分析,并对该火箭发动机壳体屈曲应力如何估计提出了建议。