低速叶型气动反问题设计方法

 低马赫数不可压流动中声速与流速大小差别巨大,采用基于可压缩流动控制方程的计算格式求解流场时,由于数值黏性的污染,解的精度低且收敛性差,通常可使用时间预处理技术来解决这一问题。在基于控制理论的优化方法中,共轭方程的Jacobian矩阵和流动方程的系数矩阵相似,因而在低流动马赫数下,求解共轭方程存在着与求解流动方程相同的数值污染和数值刚性问题。首先推导了带有预处理的Roe格式,然后发展了适合全速度流动的共轭方程求解方法,最后选取翼型和叶栅两个典型算例进行了验证。计算结果表明所发展的方法可很好地用于低马赫数时的气动反问题设计。     

COIL化学非平衡流动的一种解耦方法研究

提出了一种计算氧碘化学激光器化学非平衡流动的解耦方法.求解二维可压缩非定常N-S方程及组分连续方程,计算氧碘化学激光器中的组分混合反应流场.空间离散格式为AUSM up格式,用四步龙格-库塔方法作显式时间推进.假设混合气体为热力学完全而热值非完全气体,化学反应模型采用有限速率反应模型.使用一种"点隐式"方法来处理化学源项的刚性问题.计算结果表明本文方法可以有效解决计算中的刚性问题,与现有隐式算法相比减少了大量的矩阵运算,公式推导简单,易于实现和改进.     

跨音速喷管化学反应流数值模拟

用时间相关的半隐格式有限差分数值方法求解了化学非平衡反应跨音速喷管流场，在喷管收敛段，流动接近化学平衡状态，控制方程的刚性问题严重，数值积分困难。通过对时间差分项隐式离散、对空间差分项显式离散，流场边界采用参考平面上的特征线法计算等，成功地解决了由于化学反应有限速率带来的数值解不稳定问题。该格式简单、需要计算机存贮空间少。本文完成了一维和轴对称非平衡化学反应喷管流动计算，并与化学平衡流和冻结流的计算结果做了比较。     

轴对称Boltzmann模型方程统一算法与空天飞行环境喷管流动模拟

拦截机动飞行器周围大范围区域存在主喷/侧喷流/羽流影响,而传统的纳维-斯托克斯（Navier-Stokes, N-S）方程不能很好模拟发动机喷管扩张段出口附近流动情况,需要一种新的方法来处理这种全流域流动问题。为解决该问题,针对特定轴对称喷管内流动,本文通过数学推导确立描述不同克努森数稀薄环境条件下的轴对称喷管内流动Boltzmann模型方程,初步建立适于该模型方程的数值格式与气体动理论统一算法。通过开展同轴圆筒间的定常/非定常旋转流动以及轴对称喷管内流动数值计算研究,发现统一算法计算流场与其他途径得到的结果吻合较好,验证了统一算法在全局克努森数喷管流动模拟的适应性和可靠性。通过与低密度风洞实验对比,喷管出口核心区羽流结构一致,羽流轴线压力分布一致,表明统一算法可以有效解决喷管入口压缩段到扩张段多流域混合,尤其是出口附近稀薄气体真空低压环境流动问题。     

三维超声速混合层内标量混合的大涡模拟

对三维对流马赫数0.62的超声速混合层流动的标量混合进行大涡模拟, 控制方程对流项采用五阶精度的WENO格式求解, 小尺度涡的作用采用一方程LDKM亚格子模型处理, 过滤后的组分方程中的亚格子组分对流通量采用梯度扩散模化.模拟得到了混合层流场大尺度拟序结构以及标量场的演化过程, 研究表明标量混合过程受混合层内涡系演化所控制, 标量场具有明显的三维特征.模拟得到的速度、组分及其脉动的统计时均结果和实验结果相符较好.      

数值求解可压缩N—S方程的增量迭代法

本文在Beam-Warming格式的基础上,引入通量分裂的概念,应用行高斯迭代技术提出了一个二阶隐式的求解BFC坐标变换下的N-S方程的增量迭代法。它消除了因式分解带来的寄生误差,合理地处理了控制方程中的粘性项,具有较好的收敛性和稳定性。二维Poissuill流动和Couette流动的计算结果和精确解吻合良好。S形进气道的数值解反映出的现象和实验结果是一致的。     

一种新的用于MHD方程逆风格式的Jacobian矩阵分裂方法

针对理想MHD方程,提出了一种新的基于MacCormack算法的雅可比矩阵分裂方法,克服了原有方法稳定性差的问题,并成功地应用于理想MHD方程的求解.控制方程在非结构混合网格上进行空间离散,其中对流项采用本文发展的逆风向量分裂格式,并引入了双曲型磁场散度清除技术,时间推进为显式5步龙格-库塔方法.对MHD激波管流动和带均匀磁场干扰的二维高超声速钝头体绕流流场进行了数值模拟,得到了与参考文献相吻合的数值结果,表明本文发展的数值分裂方法可以有效地捕捉MHD流场的流动特征,并且具有比MacCormack方法更高的稳定性和计算精度.     

叶片扩压器内三维流场数值计算与实验研究

本文采用加罚有限元方法对离心压缩机叶片扩压器内流场进行了数值分析。在数值求解过程中,为了避免流动对流占优所引起的压力场波动,控制方程离散时借鉴有限差分法的技巧,进行权函数修正,通过迎风参数来控制沿流动方向上所施加的流线迎风量,保证数值求解的稳定性。叶片扩压器内紊流流动的数值计算结果表明:在其他项的假扩散被降至最小时,压力项的震荡亦被消弱。紊流场的计算采用k-ε紊流模型。同时本文对叶片扩压器内流场进行了实验测量,通过数值计算结果与实验测量值的比较分析,结果是令人满意的。最后就提高叶片扩压器的静压效率和压缩机整机性能提出了有益的建议。      

三维可压和不可压缩流动数值模拟的一种预处理多重网格方法研究(英文)

将矩阵预处理方法与多重网格方法结合,发展了适用于机翼及复杂外形气动数值优化设计的高效数值模拟方法和程序。在不改变定常流动解的前提下,对 Navier-Stokes 方程的时间导数项实施 Choi-Merkle 矩阵预处理,从而改善可压缩控制方程在低速情况下的系统刚性。Choi-Merkle 预处理最初用于二维低马赫数粘性流动数值模拟,本文将其推广应用到计算三维流动,并针对提高跨音速流动计算收敛性进行了相应的改进。预处理后控制方程采用中心格式有限体积进行空间离散,Runge-Kutta 混合多步方法进行显式时间推进求解,并应用 FAS 多重网格方法加速收敛。采用所发展的方法和程序数值模拟了绕 M6 机翼和 M100 机翼的低速和跨音速流动(马赫数从0.01 到 0.839)以及绕 F4 翼身组合体流动。计算结果与实验值吻合良好,验证了所发展的方法的正确性。算例研究表明所发展方法较大幅度地提高了三维流动数值模拟的效率,且同时适用于可压和不可压流动计算,在机翼及复杂外形气动优化设计方法具有应用前景     

A Preconditioned Multigrid Method for Efficient Simulation of Three-dimensional Compressible and Incompressible Flows

将矩阵预处理方法与多重网格方法结合,发展了适用于机翼及复杂外形气动数值优化设计的高效数值模拟方法和程序。在不改变定常流动解的前提下,对 Navier-Stokes 方程的时间导数项实施 Choi-Merkle 矩阵预处理,从而改善可压缩控制方程在低速情况下的系统刚性。Choi-Merkle 预处理最初用于二维低马赫数粘性流动数值模拟,本文将其推广应用到计算三维流动,并针对提高跨音速流动计算收敛性进行了相应的改进。预处理后控制方程采用中心格式有限体积进行空间离散,Runge-Kutta 混合多步方法进行显式时间推进求解,并应用 FAS 多重网格方法加速收敛。采用所发展的方法和程序数值模拟了绕 M6 机翼和 M100 机翼的低速和跨音速流动(马赫数从0.01 到 0.839)以及绕 F4 翼身组合体流动。计算结果与实验值吻合良好,验证了所发展的方法的正确性。算例研究表明所发展方法较大幅度地提高了三维流动数值模拟的效率,且同时适用于可压和不可压流动计算,在机翼及复杂外形气动优化设计方法具有应用前景     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.