Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

PWM full-bridge converter with natural input power factor correction

A pulsewidth modulated (PWM) full-bridge converter that simultaneously performs input power factor correction (PFC) and DC-DC conversion is proposed. The converter is the same as the standard voltage-fed PWM full-bridge converter with a diode-bridge low-pass filter front end, but with a slight modification that results in an improvement in power factor that is sufficient to satisfy the EN61000-3-2 requirements for electrical equipment. The operation of the converter is explained and analyzed, and the results of the analysis are used to determine the converter's steady-state characteristics, which are discussed in detail. A design procedure for the selection of components is then derived and demonstrated with an example. The feasibility of the converter and its ability to satisfy EN61000-3-2 requirements on electrical equipment is shown with results obtained from an experimental prototype.     

Analysis and design of series-parallel resonant power supply

A modified series-parallel high-frequency resonant DC/DC converter configuration is proposed. A simplified steady-state analysis of the converter, including the effect of a high-frequency transformer using complex circuit analysis, is presented. Based on the analysis, a simple design procedure is given. The effect of magnetizing inductances of the high-frequency transformer on the performance of the converter is discussed. Detailed experimental results obtained from a MOSFET (metal-oxide-semiconductor field-effect-transistor)-based 1-kW converter are presented to verify the analysis. The converter presented has almost constant efficiency from full load to quarter load, and the converter has load short circuit capability     

A fixed frequency LCL-Type series resonant converter

A fixed frequency LCL-type series resonant converter (SRC) which uses an inductive output filter is proposed. Steady-state analysis of the converter is presented using complex ac circuit analysis. Based on the analysis, a simple design procedure is given. Detailed space integrated control experiment (SPICE) simulation results are presented to evaluate the performance of the designed converter under varying load and supply voltage conditions. Also, detailed experimental results obtained from a metal-oxide-semiconductor field-effect transistor (MOSFET) based 500 W converter are presented to verify the analysis and SPICE simulation results. The results obtained from the analysis, SPICE simulation and the experimental converter are compared. The proposed converter requires a narrow variation in pulsewidth while maintaining lagging power factor mode of operation for a very wide variation in the load as well as supply voltage     

Improved ZCS-PWM commutation cell for IGBTs application

An improved zero-current-switching pulsewidth-modulated (ZCS-PWM) commutation cell is presented, which is suitable for high-power applications using insulated gate bipolar transistors (IGBTs) as the power switches. It provides ZCS operation for active switches and zero-voltage-switching (ZVS) operation for passive switches. Besides operating at constant frequency and reducing commutation losses, the proposed ZCS-PWM switch cell has no additional current stress and conduction loss in the main switch. To demonstrate the feasibility of the proposed ZCS-PWM commutation cell, it was applied to a boost converter. Operating principle, theoretical analysis, design guidelines, and a design example are described and verified by experiment results obtained from a prototype rated 1 kW and operating at 40 kHz. The PWM switch model and state-space averaging approach is also used to estimate and examine the steady-state and dynamic character of ZCS-PWM boost converter system. Finally, the application of the proposed soft-switching technique in the dc-dc nonisolated converters is presented.     

Analysis and design of a three-phase LCC-type resonant converter

A three-phase dc-to-dc LCC-type resonant converter with high-frequency transformer isolation is proposed. The operation and a simple analysis of the converter are presented. Design curves are obtained and a design example is given. SPICE simulation and experimental results are presented to verify the performance of the proposed converter for varying load conditions. The converter proposed has several advantages, e.g., operation in lagging PF mode for the entire load range, requires a narrow variation required in switching frequency, reduced component size and stresses, etc     

Single-stage ZVS PWM full-bridge converter

A new soft-switched ac-dc single-stage pulse width modulation (PWM) full-bridge converter is proposed. The converter operates with zero-voltage switching (ZVS), fixed switching frequency, and with a continuous input current that is sinusoidal and in phase with the input voltage. This is in contrast with other ac-dc single-stage PWM full-bridge converters that are either resonant converters operating with variable switching frequency control and high conduction losses, converters whose switches cannot operate with ZVS, or converters that cannot perform power factor correction (PFC) unless the input current is discontinuous. All converter switches operate with soft-switching due to a simple auxiliary circuit that is used for only a small fraction of the switching cycle. The operation of the converter is explained and analyzed, guidelines for the design of the converter are given, and its feasibility is shown with results obtained from an experimental prototype.     

具有功率因数校正的零电压开关谐振变换器设计

传统型PWM控制的开关电源是硬件开关，开关损耗大，不利于向小型化，轻量化发展。本提出利用零电压开关谐振技术实现功率开关管的软开关技术，从而降低开关损耗，并采用SG3525为核心的主开关控制电路，提高系统的动态响应性能，同时采用UC3854对AC／DC变换过程作了功率因数校正，以改善输入电流的波形，提高电力资源的利用率。     

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Full bridge ZCS PWM converter for high-voltage high-powerapplications

This paper presents a comprehensive study of a full bridge (FB) zero-current switched (ZCS) PWM converter which is suitable for high-voltage and high-power DC application that achieves ZCS for all active switches, and zero-voltage-switched (ZVS) operation for all diodes on the high voltage side. The given converter utilizes component parasitic parameters, particularly for the high-voltage transformer, and employs fixed-frequency phase-shift control to implement soft-switching commutations. Detailed steady state analysis of the converter power stage is presented for the first time and the major features of the converter's power stage are discussed. Small-signal characteristics are also presented and accompanied by a discussion of the controller design and implementation. A design example is also presented based on the steady state analysis and is validated by simulation. Theoretical and simulated results are in good agreement     

Design optimization for asymmetrical ZVS-PWM zeta converter

In this paper, a new soft-switching Zeta converter with an asymmetrical pulsewidth modulation (PWM) control is proposed. The proposed Zeta converter has the features of constant frequency operation, zero voltage switching (ZVS), and low voltage stress on the active switches. Moreover, it can achieve high power density, high efficiency, low switching loss, and low component count, which make converter operation at low to medium power level feasible. Operational principle of the Zeta converter is presented in detail, and a specific example is designed and implemented to verify its feasibility.     

Tapped-inductor filter assisted soft-switching PWM DC-DC power converter

A novel high-frequency transformer linked full-bridge type soft-switching phase-shift pulsewidth modulated (PWM) controlled dc-dc power converter is presented, which can be used as a power conditioner for small-scale photovoltaic and fuel cell power generation systems as well as isolated boost dc-dc power converter for automotive ac power supply. In these applications with low-voltage large-current sources, the full-bridge circuit is the most attractive topology due to the possibility of using low-voltage high-performance metal-oxide-semiconductor field-effect transistor (MOSFET) and achieving high efficiency of the dc-dc power converter. A tapped-inductor filter including the freewheeling diode is newly implemented in the output stage of the full-bridge phase-shift PWM dc-dc converter to achieve soft-switching operation for the wide load variation range. Moreover, in the proposed converter circuit, the circulating current is effectively minimized without using additional resonant circuit and auxiliary power switching devices. The practical effectiveness of the proposed soft-switching dc-dc power converter was verified in laboratory level experiment with 1 kW 100 kHz breadboard setup using power MOSFETs. Actual efficiency of 94-97% was obtained for the wide duty cycle and load variation ranges.     

Modeling of a new ZVS bi-directional dc-dc converter

A dual half-bridge (DHB) bidirectional dc-dc converter is a new proposed topology that has the advantages of decreased number of devices, soft-switching implementation, low cost, and high efficiency. Typical applications of this converter are the auxiliary power supply in fuel cell vehicles and battery charging and discharging systems where the power density, cost, weight, and reliability are critical factors. A switching-frequency-dependent state-space averaged model of the converter is developed here for either direction of power flow. This averaged model can be used to derive the steady-state characteristics and small signal dynamics of the proposed topology. It also provides a fast simulation tool to investigate the transient response of the converter. The simulated waveforms of the mathematical model are compared with the detailed circuit simulation to verify the accuracy of the modeling.     

Steady-state analysis and design of a switched-capacitor DC-DCconverter

A representative switched-capacitor DC-DC converter topology is presented, circuit operation is explained, and control strategies are identified. State-space averaging is used to analyze steady-state performance and to develop control criteria and design equations. The analytical results are verified by SPICE simulation     

并联交错式有源箝位正激变换器研究

深入分析研究了并联交错式有源箝位正激变换器的原理与设计 ,获得了功率开关实现零电压 ZVS开通的条件和关键电路参数选取准则 ,仿真与试验结果均证实了理论分析的正确性。研究结果表明 ,并联交错式有源箝位正激变换器具有优良的电气性能 ,特别适用于大功率分布式电源系统     

Self-Adapting dc Converter for Solar Spacecraft Power Supply Selbstanpassender Gleichstromwandler für die Energieversorgung eines Sonnensatelliten

The voltage-current characteristic of solar cells that provide power for a spacecraft can vary over a wide range. For maximum power transfer from the solar cells to the battery system a power converter has to be designed that adjusts its input impedance to a value equal to the output impedance determined by the operating power characteristic of the solar cells. This paper discusses a circuit and calculations for a design to match this condition. The proposed power converter is simple, lightweight, and reliable and will be used in the Sunblazer satellite.     

Buck-flyback DC-DC converter

It is difficult to obtain a large input/output voltage ratio with a DC-DC converter, because the duty factor d may not reach very small values. For the same reason, it is difficult to obtain an output voltage that is adjustable in a large range. A DC-DC converter circuit is proposed that overcomes this limitation by performing a voltage ratio d²/(1-d) in the best operating mode. Circuit operation is analyzed, operating modes are evidenced, and the voltage ratio is deduced in each operating mode as a function of output current, duty factor, and circuit component values. Boundary conditions between different operating modes are obtained; consequently, it is concluded that these conditions do not occur for some operating modes. Component ratings are summarized, to facilitate circuit design. The buck-flyback DC-DC converter is very suitable for low-voltage (e.g. computer) power supplies and for power supplies with the output voltage (adjustable in a large range) supplied from the mains without a mains voltage transformer     

MPPT of photovoltaic systems using extremum - seeking control

A stability analysis for a maximum power point tracking (MPPT) scheme based on extremum-seeking control is developed for a photovoltaic (PV) array supplying a dc-to-dc switching converter. The global stability of the extremum-seeking algorithm is demonstrated by means of Lyapunov's approach. Subsequently, the algorithm is applied to an MPPT system based on the "perturb and observe" method. The steady-state behavior of the PV system with MPPT control is characterized by a stable oscillation around the maximum power point. The tracking algorithm leads the array coordinates to the maximum power point by increasing or decreasing linearly with time the array voltage. Off-line measurements are not required by the control law, which is implemented by means of an analog multiplier, standard operational amplifiers, a flip-flop circuit and a pulsewidth modulator. The effectiveness of the proposed MPPT scheme is demonstrated experimentally under different operating conditions.     

State Trajectories Used to Observe and Control DC-to-DC Converters

State-plane analysis techniques are employed to study the voltage stepup energy-storage dc-to-dc converter. Within this framework, an example converter operating under the influence of a constant on-time and a constant frequency controller is examined. Qualitative insight gained through this approach is used to develop a conceptual free-running control law for the voltage stepup converter which can achieve steady-state operation in one on/off cycle of control. Digital computer simulation data are presented to illustrate and verify the theoretical discussions presented.     

A design procedure for the phase-controlled parallel-loadedresonant inverter

High-frequency-link power conversion and distribution based on a resonant inverter has been recently proposed. The design of several topologies is reviewed and a simple approximate design procedure is developed for the phase-controlled parallel-loaded resonant inverter. This design procedure seeks to ensure the expected benefits of resonant conversion and is verified by data from a laboratory 2.5 kVA, 20-kHz converter. A simple phasor analysis is introduced as a useful approximation for design purposes. Experimental results show that under transient conditions such as load short-circuit, a reversal of the expected commutation sequence is possible. This should be accounted for in the design of the power circuit, or prevented by the design of the controller