Quality factor and dose equivalent investigations aboard the Soviet space station MIR.

Since Dec 1988, date of the French-Soviet joint space mission "ARAGATZ", the CIRCE device (Compteur Intégrateur de Rayonnement Complexe dans l'Espace) had recorded dose equivalent and quality factor inside the MIR station (380-410 km, 51.5 degrees). After the initial gas filling two years ago, the low pressure tissue equivalent proportional counter is still in good working conditions. Some results of three periods, viz Dec 1988, Mar-Apr 1989 and Jan-Feb 1990 are presented. The average dose equivalent rates measured are respectively 0.6, 0.8 and 0.6 mSv/day with a quality factor equal to 1.9. Some detailed measurements show the increasing of the dose equivalent rates through the SAA and near polar horns. The real time determination of the quality factors allows to point out high LET (Linear Energy Transfer) events with quality factors in the range 10-20.     

Study of the radiation environment on MIR space station with SILEYE-2 experiment.

In this work we present preliminary results of nuclear composition measurements on board space station MIR obtained with SILEYE-2 particle telescope. SILEYE-2 was placed on MIR in 1997 and has been working since then. It consists of an array of 6 active silicon strip detectors which allow nuclear and energetic identification of cosmic rays in the energy range between approximately 30 and 200 MeV/n. The device is attached to an helmet and connected to an eye mask which shields the cosmonaut eyes from light and allow studies of the Light Flashes (LF) phenomenon. In addition to the study of the causes of LF, the device is used to perform real time long term radiation environment monitoring inside the MIR, performing measurements in solar quiet and active days.     

Austrian dose measurements onboard space station MIR and the International Space Station--overview and comparison.

The Atominstitute of the Austrian Universities has conducted various space research missions in the last 12 years in cooperation with the Institute for Biomedical Problems in Moscow. They dealt with the exact determination of the radiation hazards for cosmonauts and the development of precise measurement devices. Special emphasis will be laid on the last experiment on space station MIR the goal of which was the determination of the depth distribution of absorbed dose and dose equivalent in a water filled Phantom. The first results from dose measurements onboard the International Space Station (ISS) will also be discussed. The spherical Phantom with a diameter of 35 cm was developed at the Institute for Biomedical Problems and had 4 channels where dosimeters can be exposed in different depths. The exposure period covered the timeframe from May 1997 to February 1999. Thermoluminescent dosimeters (TLDs) were exposed inside the Phantom, either parallel or perpendicular to the hull of the spacecraft. For the evaluation of the linear energy transfer (LET), the high temperature ratio (HTR) method was applied. Based on this method a mean quality factor and, subsequently, the dose equivalent is calculated according to the Q(LET infinity) relationship proposed in ICRP 26. An increased contribution of neutrons could be detected inside the Phantom. However the total dose equivalent did not increase over the depth of the Phantom. As the first Austrian measurements on the ISS dosimeter packages were exposed for 248 days, starting in February 2001 at six different locations onboard the ISS. The Austrian dosimeter sets for this first exposure on the ISS contained five different kinds of passive thermoluminescent dosimeters. First results showed a position dependent absorbed dose rate at the ISS.     

Semi-analytical theory of mean orbital motion for geosynchronous space debris under gravitational influence

This paper provides a hamiltonian formulation of the equations of motion of an artificial satellite or space debris orbiting the geostationary ring. This theory of order 1 has been formulated using canonical and non-singular elements for eccentricity and inclination. The analysis is based on an expansion in powers of the eccentricity and of the inclination. The theory accounts for the influence of the Earth gravity field expanded in spherical harmonics, paying a particular attention to the resonance occurring for geosynchronous objects. The luni-solar perturbations are also taken into account. We present the resonant motion and its main characteristics: equilibria, stability, fundamental frequencies and width of the resonant area by comparison with a basic analytical model. Finally, we show some results concerning the long term dynamics of a typical space debris under the influence of the gravitational field of the Earth and the luni-solar interactions.     

Cosmic dust physical properties and theICAPS facility on board the ISS

Cometary comae, cometary tails, and the interplanetary dust cloud, are low density dust clouds built of cosmic dust particles. Light scattering observations, from in-situ space probes and remote observatories, are a key to their physical properties. This presentation updates results on cometary and interplanetary dust derived from such observations (with emphasis on polarization), and compares them with results on asteroidal regoliths. The polarization phase curves follow similar trends, with parameters that may vary from one object to another. The wavelength dependence is highly variable, although it is usually linear in the visible domain. It may be suggested (from observations, modeling and laboratory measurements) that these dust particles are irregular, with a size greater than the wavelength, and that cometary dust is highly porous, as compared to asteroidal or interplanetary dust. Sophisticated numerical models and laboratory measurements on dust analogues are indeed required to interpret without any ambiguity the ensemble of results. The opportunity offered by the ICAPS facility (an ESA project selected for the ISS, now in phase B) to deduce the physical properties of cosmic dust particles from their optical properties, as well as their evolution (breaking-off and agglomeration, ices condensation and evaporation), is presented.     

A flash on the moon caused by orbital debris

Sun glinting from a satellite in earth orbit is suggested as the probable cause of a reported lunar flash observed on May 23, 1985. This conflicts with the suggestion that a lunar ionization phenomenon is the source and points out concern that flashes from space debris must always be considered in the investigation of sky — flash discoveries.     

Two-dimensional phase plane structure and the stability of the orbital motion for space debris in the geosynchronous ring

Based on the orbital resonance model, we study the two-dimensional phase plane structure of the motion of space debris orbiting the geosynchronous ring under the combined effects of the tesseral harmonics J₂₂, J₃₁ and J₃₃ of the Earth’s gravitational field. We present the main characteristic parameters of the two-dimensional phase plane structure. We also analyze the stability of the two-dimensional phase plane structure with numerical method. Our main findings indicate that the combined effects of the tesseral harmonics J₂₂, J₃₁ and J₃₃ fully determine the two-dimensional phase plane structure of the space debris, and it remains robust under the effect of the Earth’s actual gravitational field, the luni-solar perturbations and the solar radiation pressure with the normal area-to-mass ratios.     

Cosmic ray anisotropy based on Yakutsk station in real time

The method has been developed to calculate galactic cosmic ray anisotropy parameters by using on-line data of the neutron monitor 24-NM-64 and muon telescope at the Yakutsk station. The preliminary analysis shows that characteristic changes in the anisotropy parameters caused by the first spherical harmonics of cosmic ray angular distribution are observed 1–2 days before the onset of the most part of large-scale geophysical disturbances on the Earth. There is reason to believe that the attraction of data of geophysical observations of other kinds will allow to develop the forecast methods for the arrival of large-scale interplanetary disturbances at the Earth.     

Cavity clock experiments on space station

With the start of the Space Station era a new group of fundamental physics experiments is being developed to take advantage of the unique conditions available. Recently a microwave cavity clock experiment was selected to perform experiments in relativity. The project has four main goals: an improved test of Local Position Invariance, improved Kennedy–Thorndyke and Michelson–Morley type experiments, and an enhancement of the performance of atomic clocks being developed elsewhere for use in space. We describe the background and status of the project, which involves the development of superconducting microwave oscillators with high frequency stability. On the International Space Station unwanted cavity frequency variations are expected to be caused mainly by acceleration effects due to residual drag and vibration, temperature variations, and fluctuations in the energy stored in the cavity. At present, acceleration effects appear to be the predominant limit, and a new cavity support system has been fabricated to reduce the effect, and three assemblies are in test. Fractional frequency stabilities in the low 10⁻¹⁶ range are expected on time scales of minutes.     

MULPEX: A compact multi-layered polymer foil collector for micrometeoroids and orbital debris

Detailed studies of preserved hypervelocity impact residues on spacecraft multi-layer insulation foils have yielded important information about the flux of small particles from different sources in low-Earth orbit (LEO). We have extended our earlier research on impacts occurring in LEO to design and testing of a compact capture device. MUlti-Layer Polymer EXperiment (MULPEX) is simple, cheap to build, lightweight, of no power demand, easy to deploy, and optimised for the efficient collection of impact residue for analysis on return to Earth. The capture medium is a stack of very thin (8 and 40 μm) polyimide foils, supported on poly-tetrafluoroethylene sheet frames, surrounded by a protective aluminium casing. The uppermost foil has a very thin metallic coating for thermal protection and resistance to atomic oxygen and ultra-violet exposure. The casing provides a simple detachable interface for deployment on the spacecraft, facing into the desired direction for particle collection. On return to the laboratory, the stacked foils are separated for examination in a variable pressure scanning electron microscope, without need for surface coating. Analysis of impact residue is performed using energy dispersive X-ray spectrometers. Our laboratory experiments, utilising buck-shot firings of analogues to micrometeoroids (35–38 μm olivine) and space debris (4 μm alumina and 1 mm stainless steel) in a light gas gun, have shown that impact residue is abundant within the foil layers, and preserves a record of the impacting particle, whether of micrometer or millimetre dimensions. Penetrations of the top foil are easily recognised, and act as a proxy for dimensions of the penetrating particle. Impact may cause disruption and melting, but some residue retains sufficient crystallographic structure to show clear Raman lines, diagnostic of the original mineral.     

Pulsed laser interactions with space debris: Target shape effects

Among the approaches to the proposed mitigation and remediation of the space debris problem is the de-orbiting of objects in low Earth orbit through irradiation by ground-based high-intensity pulsed lasers. Laser ablation of a thin surface layer causes target recoil, resulting in the depletion of orbital angular momentum and accelerated atmospheric re-entry. However, both the magnitude and direction of the recoil are shape dependent, a feature of the laser-based remediation concept that has received little attention. Since the development of a predictive capability is desirable, we have investigated the dynamical response to ablation of objects comprising a variety of shapes. We derive and demonstrate a simple analytical technique for calculating the ablation-driven transfer of linear momentum, emphasizing cases for which the recoil is not exclusively parallel to the incident beam. For the purposes of comparison and contrast, we examine one case of momentum transfer in the low-intensity regime, where photon pressure is the dominant momentum transfer mechanism, showing that shape and orientation effects influence the target response in a similar, but not identical, manner. We address the related problem of target spin and, by way of a few simple examples, show how ablation can alter the spin state of a target, which often has a pronounced effect on the recoil dynamics.     

Cosmic dust analog simulation in a microgravity environment: the STARDUST program.

We have undertaken a project called STARDUST which is a collaboration with Italian and American investigators. The goals of this program are to study the condensation and coagulation of refractory materials from the vapor and to study the properties of the resulting grains as analogs to cosmic dust particles. To reduce thermal convective currents and to develop valuable experience in designing an experiment for the Gas-Grain Simulation Facility aboard Space Station Freedom we have built and flown a new chamber to study these processes under periods of microgravity available on NASA's KC-135 Research Aircraft. Preliminary results from flights with magnesium and zinc are discussed.     

The impact of alternative mission models on the future orbital debris environment

In reviewing discussions of future directions for space activity, it becomes obvious that there are a large number of groups formulating a wide diversity of plans for the future use of space. These plan alternatives are being made to account for user needs, technology development constraints, economic constraints, and launch support, and each of the plans will have direct or indirect effects on the orbital debris environment in terms of mass to orbit, deposition of operational debris, and control of accidental breakups. Thus it is important to develop the ability to project future debris states for a range of possible space traffic scenarios. The impact that these possible traffic environments would have on space operations forms the basis for studies of alternative options for the usage of space. In this paper, the effects on the orbital debris environment of a base-line mission model and two alternatives are investigated, using a numerical debris environment simulation code under development at JSC.     

Impact effects from small size meteoroids and space debris

When the impact risk from meteoroids and orbital debris is assessed the main concern is usually structural damage. With their high impact velocities of typically 10–20 km/s millimeter or centimeter sized objects can puncture pressure vessels and other walls or lead to destruction of complete subsystems or even whole spacecraft. Fortunately chances of collisions with such larger objects are small (at least at present). However, particles in the size range 1–100 μm are far more abundant than larger objects and every orbiting spacecraft will encounter them with certainty. Every solar cell (8 cm² area) of the Hubble Space Telescope encountered on average 12 impacts during its 8.25 years of space exposure. Most were from micron sized particles.     

Protecting and manoeuvring of spacecraft in space debris environment

The paper gives an overview on the fields of debris research performed at the TUBS. The orbital debris flux of all objects larger than 1cm has been established and simulated by a mathematical model in the past mainly on the basis of simulating explosion fragments. However the flux in the millimeter and submillimeter size range seems to be largely influenced by collisions and their ejecta on high circular or on eccentric orbits. The angular distribution of the impact flux on targets at various altitudes and on various inclinations are presented. This angular distribution has also influence on the surface impact flux on a space station, where also the self shielding has to be considered. Results for the ISS are presented. The risk of impacts of larger not shieldable objects on a space station may become too high, so that collision avoidance manoeuvres must be envisaged, the feasibility of which using onboard detectors is discussed.     

Stabilization of an injected conducting layer for artificially enhancing drag on orbital debris

The evolution of a magnetized conducting medium suspended in magnetic and gravitational fields is examined. In this paper some effects of the influence of velocity fields on the linear stability properties of such layers are investigated. A fully compressible, three-dimensional analysis of the layer is described. The relevant equations are derived and then solved by the MagnetoHydroDynamic SPEctral Compressible Linear Stability (MHDSPECLS) algorithm, a Chebyshev collocation code. The code allows for the computation of magnetic and thermal effects. A complete stabilization of the system is found above a critical velocity of approximately 2500 m/s.     

A robotic telescope network for space debris identification and tracking

The two TAROT (Télescopes à Action Rapide pour les Objets Transitoires; Rapid Action Telescopes for Transient Objects) installations are fully robotic optical observatories with optimized observation scheduling, data processing and archiving. Zadko is a 1 m telescope in Western Australia. The fully robotisation of the Zadko telescope has just been completed; it is now included in the TAROT network. In this paper we provide an overview of this international network of robotic optical telescopes. We discuss the advantages of using the network to participate in a satellite and space debris tracking program. This network will access almost all geostationary belt objects, and provide the first real-time satellite positioning capability. The inclusion of the 1 m Zadko telescope into the network significantly extends the efficiency and sensitivity of the existing two telescope configuration.     

Radiation environment on the Mir orbital station during solar minimum.

The Mir station has been in a 51.65 degrees inclination orbit since March 1986. In March 1995, the first US astronaut flew on the Mir-18 mission and returned on the Space Shuttle in July 1995. Since then three additional US astronauts have stayed on orbit for up to 6 months. Since the return of the first US astronaut, both the Spektr and Priroda modules have docked with Mir station, altering the mass shielding distribution. Radiation measurements, including the direct comparison of US and Russian absorbed dose rates in the Base Block of the Mir station, were made during the Mir-18 and -19 missions. There is a significant variation of dose rates across the core module; the six locations sampled showed a variation of a factor of nearly two. A tissue equivalent proportional counter (TEPC) measured a total absorbed dose rate of 300 microGy/day, roughly equally divided between the rate due to trapped protons from the South Atlantic Anomaly (SAA) and galactic cosmic radiation (GCR). This dose rate is about a factor of two lower than the rate measured by the thinly shielded (0.5 g cm-2 of Al) operational ion chamber (R-16), and about 3/2 of the rate of the more heavily shielded (3.5 g cm-2 of Al) ion chamber. This is due to the differences in the mass shielding properties at the location of these detectors. A comparison of integral linear energy transfer (LET) spectra measured by TEPC and plastic nuclear track detectors (PNTDs) deployed side by side are in remarkable agreement in the LET region of 15-1000 keV/micrometer, where the PNTDs are fully efficient. The average quality factor, using the ICRP-26 definition, was 2.6, which is higher than normally used. There is excellent agreement between the measured GCR dose rate and model calculations, but this is not true for trapped protons. The measured Mir-18 crew skin dose equivalent rate was 1133 microSv/day. Using the skin dose rate and anatomical models, we have estimated the blood-forming organ (BFO) dose rate and the maximum stay time in orbit for International Space Station crew members.     

Accommodations for earth-viewing payloads on the international space station

The design of the International Space Station (ISS) includes payload locations that are external to the pressurized environment. These external or attached payload accommodation locations will allow direct access to the space environment at the ISS orbit and direct viewing of the earth and space. NASA sponsored payloads will have access to several different types of standard external locations; the S3 Truss Sites, the Columbus External Payload Facility (EPF), and the Japanese Experiment Module Exposed Facility (JEM-EF). As the ISS Program develops, it may also be possible to locate external payloads at the P3 Truss Sites or at non-standard locations similar to the handrail-attached payloads that were flown during the MIR Program. Earth-viewing payloads may also be located within the pressurized volume of the US Lab in the Window Observational Research Facility (WORF). Payload accommodations at each of the locations will be described, as well as transport to and retrieval from the site.     

A novel signal processing approach for LEO space debris based on a fence-type space surveillance radar system

The increase in space debris can seriously threaten regular activities in the Low Earth Orbit (LEO) environment. Therefore, it is necessary to develop robust, efficient and reliable techniques to understand the potential motions of the LEO debris. In this paper, we propose a novel signal processing approach to detect and estimate the motions of LEO space debris that is based on a fence-type space surveillance radar system. Because of the sparse distribution of the orbiting debris through the fence in our observations, we formulate the signal detection and the motion parameter estimation as a sparse signal reconstruction problem with respect to an over-complete dictionary. Moreover, we propose a new scheme to reduce the size of the original over-complete dictionary without the loss of the important information. This new scheme is based on a careful analysis of the relations between the acceleration and the directions of arrival for the corresponding LEO space debris. Our simulation results show that the proposed approach can achieve extremely good performance in terms of the accuracy for detection and estimation. Furthermore, our simulation results demonstrate the robustness of the approach in scenarios with a low Signal-to-Noise Ratio (SNR) and the super-resolution properties. We hope our signal processing approach can stimulate further work on monitoring LEO space debris.