航空发动机用环境障涂层的发展

碳化硅纤维增强碳化硅陶瓷基复合材料（CMC-SiCf/SiC）具有低密度、耐高温、高比强度等优点,是下一代高推重比航空发动机热端部件的主要候选材料之一。然而,该材料在燃气环境中面临严重的腐蚀问题。因此,需要在材料表面涂覆环境障涂层进行防护。本文综述了环境障涂层的选材要求、材料发展阶段、涂层制备技术、涂层考核与失效等,指出了环境障涂层今后在选材、制备、考核与评价的发展方向。     

等离子喷涂(RE–Al)TaO4钽酸盐环境障涂层性能研究

陶瓷基复合材料作为广泛应用于航空航天领域的先进结构材料,在实际服役环境中依赖于环境障涂层的保护作用,钽酸盐以其优异的高温热–力学性能和与陶瓷基复合材料适配的热膨胀系数((3.5～5.5)×10^–6 K^–1)成为极具潜力的环境障涂层材料。通过大气等离子喷涂(Atmospheric plasma spraying,APS)工艺在碳化硅纤维增强碳化硅基复合材料(SiC_f/SiC)表面成功制备了(AlTa_x)B_2–2xO₄/(RE–Al)TaO₄复合涂层,探索了涂层的最佳热处理工艺条件,同时对不同涂层结构方案的复合材料涂层试样进行1300℃热疲劳考核和弯曲强度测试,筛选出具有最优抗热疲劳性能的涂层结构,并通过XRD、SEM以及金相显微镜对涂层的表面形貌、裂纹扩展及元素分布进行了分析表征,相对于传统材料涂层,钽酸盐复合涂层以其在高温下优越的综合性能成为极具潜力的环境障涂层。     

C/C复合材料表面双辉等离子渗铱微观结构分析

通过双层辉光等离子表面合金化方法,在C/C复合材料表面成功制得铱涂层,并研究了铱涂层相组成和微观结构.铱涂层呈亮银白色,致密且表面光滑均匀,无明显缺陷.XRD和SEM研究表明:铱涂层呈多晶态,晶粒呈簇柱状晶并与C/C复合材料表面垂直,具有嵌入式结构,晶粒平均直径为0.5 um,铱涂层截面呈现明显的柱状晶生长,涂层内部有少量裂纹和针孔但并未贯穿.     

碳化硅纤维增韧碳化硅陶瓷基复合材料的发展现状及其在航空发动机上的应用

碳化硅纤维增韧碳化硅陶瓷基复合材料(SiC/SiC CMC)具有低密度、高强高模、耐高温抗氧化、抗蠕变、抗热冲击、耐腐蚀、材料热膨胀系数小等性能优点,在航空发动机上具有巨大的应用潜力。从碳化硅纤维、制备工艺、界面相和涂层等方面综述了国内外SiC/SiC CMC的发展现状,并基于SiC/SiC CMC的性能特点对其在航空发动机燃烧室火焰筒、混合器、涡轮罩环/静子叶片/转子叶片、喷管调节片等热端部件上的应用情况进行了介绍。     

CVD-SiC 涂层的C/ C-SiC 复合材料的抗烧蚀性能

采用CVD法,1 050℃在三维针刺C/C-SiC复合材料表面制备SiC涂层,研究稀释气体与载气流量比分别为4∶1和2∶1制备条件下涂层的晶体结构、表面和断面的微观形貌,对比了涂层前后C/C-SiC复合材料的抗烧蚀性能.结果表明:稀释气体流量降低其制备的SiC涂层更加平整致密,与基体结合程度更好,沉积产物均为单一的β-SiC结晶相.在600 s的氧化烧蚀下,两种流量比条件下制备CVD-SiC涂层的C/C-SiC复合材料的线烧蚀率比未涂层的分别降低34％和50％,质量烧蚀率分别降低70％和75％,抗氧化烧蚀性能明显提高.     

疲劳损伤对3DC／SiC复合材料裂纹分布的影响

采用x2拟合优度检验方法对疲劳试验前后3D C/SiC复合材料基体和涂层裂纹分布规律进行研究.结果表明,原始试样中3D C/SiC复合材料基体和涂层裂纹间距分别服从分布函数为N(143.75,56.782)和N(562.59,100.092)的正态分布,疲劳后基体和涂层裂纹间距分别服从分布函数为N(105.48,29.162)和N(227.89,25.232)的正态分布.疲劳可以促使新裂纹的产生,但不能改变基体和涂层裂纹间距分布的基本特征,这是由3DC/SiC复合材料的编织结构所决定的.     

铝基复合材料增强体碳、碳化硅和氧化铝表面涂层研究进展

基体与增强体间的界面对金属基复合材料的性质起着重要的作用。通过增强体表面处理和表面涂层可以使界面的性质得以改善。增强体涂层可分为金属涂层、陶瓷涂层 ;单层和多层涂层。涂层的常用制备方法有 :化学镀法、化学气相沉积法及溶胶 凝胶法等。本文针对铝基复合材料三种重要的增强体 :碳、碳化硅和氧化铝表面涂层以及它们对铝基复合材料的界面和性能的影响进行综述     

平纹机织多元多层碳化硅陶瓷基复合材料的等效弹性模量预测

 针对平纹机织多元多层碳化硅陶瓷基复合材料,按照“从底向上”的顺序考虑了纤维丝/界面/基体尺度以及纤维束/基体/涂层尺度下的微结构有限元模型。采用能量法依次进行了两个尺度上的等效性能计算,首先在纤维丝/界面/基体的尺度上计算了纤维束的等效弹性参数,然后将这些参数代入到纤维束/基体/涂层尺度微结构模型中,计算得到复合材料的整体弹性常数。数值计算结果与实验结果吻合较好,验证了所提计算方法以及模型的有效性。     

航空发动机用连续SiC_f/SiC复合材料制备工艺及应用前景

介绍了连续碳化硅纤维增强碳化硅基复合材料(SiC_f/Si C)常见的3种制备工艺,即化学气相渗透(CVI)工艺、前驱体浸渍/裂解(PIP)工艺及熔渗(MI)工艺的不同特点,探讨了国外不同工艺制备的复合材料的基本性能,并简述了SiC_f/SiC陶瓷基复合材料在航空发动机上的应用情况,以期为该材料在国内航空发动机领域的发展提供一定的参考。     

雷达/激光复合隐身材料的实验研究

采用双层涂敷法,在雷达隐身材料表层喷涂薄层的激光隐身材料,制备了双层型雷达/激光复合隐身材料,并用紫外-可见-近红外分光光度计分别测试了涂敷激光涂层前后的激光反射率以及在微波暗室内测试了涂敷激光涂层前后的雷达波反射率.结果表明：涂敷激光涂层后,在1.06 μm处的反射率由2.24%降低到0.13%,在8～15 GHz范围内,对雷达波反射率没有不利影响,均小于-7.5 dB,且有一定的改善,显示该材料在8～15 GHz范围内可以很好地实现雷达与激光的复合隐身,在其他波段的兼容性有待于进一步研究.     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.