A self-normalizing gradient search adaptive array algorithm

A method is described to normalize the step parameter and perturbation amount used for gradient search adaptive algorithms. The step normalization assures rapid stable convergence. The perturbation normalization also assures rapid stable convergence and limits the output perturbation noise to a level below thermal noise. The normalizations are computationally simple and are consistent with the use of a single receiver at the adaptive array output. Results are presented to verify the robustness of the technique.<>     

The Output Pdf of a Polarity Coincidence Correlation Detector

A general expression is derived for the probability density function of the output of a cross correlator, the inputs of which are assumed to consist of clipped sine waves of similar frequency plus uncorrelated, stationary Gaussian noise. The correlator output is shown to be a piecewise linear function of the random phase difference between the two input processes; hence, the density function for the correlator output is obtained by a relatively simple transformationfrom the probability density function of the random phase difference.     

A Fast Beamforming Algorithm for Large Arrays

This beamforming algorithm is written specifically for array radars in which the number of array elements K is very large compared with the number of jammers L the radar is designed to suppress. It uses a set of M noise vectors to construct a basis for the jammer component of the antenna output vectors. The component of the quiescent weight vector orthogonal to each basis vector is calculated, renormalized to unit length, and identified as the adapted weight vector. This algorithm is effective in the suppression of many types of jammers. The number of noise samples M required in the construction of the adapted weight vector is approximately equal to L. In the special case of L narrowband noise jammers, for example, a choice of M = L usually reduces the receiver output jammer power to a few dBs above the white noise background. It is permissible to have M相似文献   

Calculation of Output Noise Variances for Discrete Time-Invariant Filters

Certain calculations to minimize output noise variance are introduced. Many applied problems in sampled data systems require that data be smoothed in the presence of noise for the prediction of future positions, velocities, or accelerations. Smoothing coefficients in discrete time-invariant filters are computed to minimize the output noise variance, but under the constraints that the function and derivatives be predicted ahead. The output noise variance is seen to be a function of the input noise, the number of input signals (N+1) that the filter has to smooth, and the prediction time ?T. Four examples are given in the derivation of smoothing coefficients for step and ramp inputs subjected to either almost white noise or Gaussian-Markoff noise. The examples illustrate the number of constraint relations that the filter smoothing coefficients must satisfy for function and/or derivative convergence under noise-free conditions. The smoothing coefficients are also a function of the type of noise input into the system or the discrete filter. From the examples, it can be observed that as N becomes larger, the output noise variance becomes smaller, but the computation time is increased.     

A Semi-Empirical Approach to the PLL Threshold

This correspondence considers the response of the PLL near threshold to an input consisting of a modulated carrier and white, Gaussian noise. For high input signal-to-noise power ratios ?, the output noise power is Gaussian with a parabolic spectrum. As ? is decreased, the PLL tends to lose lock which gives rise to impulses or ?spikes? in the output with a resulting white power spectrum. The additional output noise due to these ?spikes? causes a threshold in the output signal-to-noise ratio. Unfortunately the loss of lock rate in the PLL depends on the modulation as well as the noise power. A semiempirical approximate expression for the loss of lock rate as a function of the noise and sinusoidal frequency modulation is presented and is used to determine the optimum design procedure for PLL's to demodulate FM signals of varying modulation indexes, ?.     

Noise Prediction for Rate Multiplier and Binary Adder Frequency Synthesizers

The theory for design of a rate multiplier or a binary adder frequency synthesizer for a specified level of noise attenuation is developed. Examples are presented to demonstrate the design procedure and the pattern of the pulse train output. The phase jitter associated with each pulse is characterized and illustrated in the time domain. The maximum absolute phase deviation is used as a measure of the phase modulation amplitude of the pulse train. Computer simulation resulted in simple equations approximating the amplitude of worst case spectral components.     

Some Matched Filter Configurations for Infrared Systems

An analysis of the output of three alternative matched filter configurations in an infrared scanning system model is presented. The sensor is corrupted by thermal noise, generation-recombination noise, photon noise, and modulation noise, the latter providing an extreme discoloration in the signal passband. Expressions for the signal voltage density spectrum, signal pulse shape, noise power spectrum, and average noise power at the matched filter output are derived where the integral evaluations attendant to these derivations do not appear elsewhere in the literature. The paper also provides graphical displays of the signal-to-noise power ratio at the filter output versus various system parameters, noise power spectrum out of the matched filter versus ?, and the signal pulse shape out of the filter versus time. Also included are discussions of practically realizable approximations to the matched filters and curve fitting techniques for the signal pulse shape function.     

Detection Performance of the Cell Averaging LOG/CFAR Receiver

The cell averaging LOG/CFAR receiver is a special implementation of a constant-false-alarm-rate (CFAR) receiver in which the noise level estimate is derived from a set of contiguous time samples of the output of a logarithmic (LOG) detector as obtained from a tapped delay line. This CFAR receiver is capable of operating over a larger dynamic range of noise levels than a conventional cell averaging CFAR receiver, but with somewhat poorer detectability. The performance in stationary Gaussian noise of the cell averaging LOG/CFAR receiver with no post-detection integration is determined in this paper. For a small number of reference noise samples, results were obtained by a Monte Carlo simulation using the technique of importance sampling. For a large number of reference noise samples, a second moment analysis gave the desired results. Both these results can be summarized in the following simple formula, NLOG = 1.65NLIN - 0.65, which relates the number of reference samples required by each of the two receivers for equivalent performance. Thus, for the cell averaging LOG/CFAR receiver to give the same detection performance as the conventional cell averaging CFAR receiver, the number of reference noise samples has to be increased by up to 65 percent.     

The Effect of Hard Limiting an Angle-Modulated Signal Plus Noise

The effect of hard limiting an angle-modulated signal plus narrow-band Gaussian noise is analyzed. Several examples are considered?sinusoidal angle modulation, Gaussian angle modulation, and biphase angle modulation. The general conclusion is that when a zonal band-pass filter is used, which rejects dc and second harmonics, an angle-modulated signal plus Gaussian noise provides the same output signal-to-noise ratio as shown by Davenport for a CW signal plus Gaussian noise. However, when a narrow bandpass filter is used, which has a bandwidth approximately equal to the input angle-modulated signal, an angle-modulated signal plus Gaussian noise has a better output signal-to-noise ratio than a CW signal plus Gaussian noise.     

Detection of Known Signals in Nonstationary Noise

The basic design of a nonlinear, time-invariant filter is postulated for detecting signal pulses of known shape imbedded in nonstationary noise. The noise is a sample function of a Gaussian random process whose statistics are approximately constant during the length of a signal pulse. The parameters of the filter are optimized to maximize the output signal-to-noise ratio (SNR). The resulting nonlinear filter has the interesting property of approximating the performance of an adaptive filter in that it weights each frequency band of each input pulse by a factor that depends on the instantaneous noise power spectrum present at that time. The SNR at the output of the nonlinear filter is compared to that at the output of a matched filter. The relative performance of the nonlinear system is good when the signal pulses have large time-bandwidth products and the instantaneous noise power spectrum is colored in the signal pass band.     

低频噪声源的测试方法

介绍了针对低频噪声源三种参数的测试方法.讨论了低频噪声源的最大输出功率、噪声输出幅度以及噪声带宽测试的实现途径.     

Ideal Limiting of Periodic Signals in Random Noise

A method based on Hermite polynomials is developed for analysis of the output resulting from passing Fourier expandable signals and noise through general zero-memory devices. New results are developed for the output time and autocorrelation functions. Special results are generated for an ideal clipper. Techniques for obtaining results for practical cases are discussed. The method itself can be modified and applied to non-Gaussian noise and general nonlinear devices with nondeterministic signals.     

Automatic Controller for a Sweeping Microwave Receiver

The Automatic System Controller (ASC) is a very simple automatic data processing system designed to provide unattended operation of the R-31 receiver, a sweeping microwave receiver. With the receiver set to operate in the scanning mode, its video output is processed by the ASC, which recognizes by thresholding the presence of a signal in the receiver pass band. When the threshold is exceeded, a receiver sweep stop is actuated, an appropriate receiver mode is selected, and an on-site tape recorder is turned on. To enhance signal acquisition, the ASC provides noise leveling gain control, the gating of undesirable signals, and useful aids for an operator attending the receiver.     

A Method for Setting a Test Signal Level Relative to Noise

A method is described for adjusting the leval of an RF test signal generator relative to the noise level at the receiver output. The method compares a detected output to a threshold and counts the number of times noise and signal plus noise cross the threshold in a given number of tries. By setting the threshold at a given false alarm probability for noise alone and then adding the test signal and adjusting its level to give a specified detection probability, the signal-to-noise ratio can be calibrated to an accuracy that depends on the number of samples used to measure the probabilities. The false alarm and detection probabilities are given for best accuracy as well as the rms error in signal-to-noise ratio as a function of the number of samples used.     

超流体物质波干涉陀螺仪的噪声研究

 陀螺仪的精度与其噪声密切相关,为开发新型高精度的超流体物质波干涉陀螺仪,必须对其噪声进行系统研究。根据超流体陀螺噪声产生的机理,分析了该陀螺噪声的来源,并把超流体陀螺的噪声类型归纳为:热、锁定值波动、温度波动、频率波动和检测元件等。在建立了各噪声数学模型的基础上,利用超流体陀螺通用的参数,对其噪声进行了分析。分析结果表明:热噪声与陀螺的结构参数和工作参数相关,与被测角速度无关;锁定值波动噪声只与结构参数相关;其他噪声与结构参数、工作参数和被测角速度都相关;检测元件、频率波动和锁定值波动噪声是构成超流体陀螺输出噪声的主要因素;在角速度变化量的范围内,超流体陀螺的输出噪声非线性变化,在1 Hz的带宽下,其变化范围为-7到-6次方的数量级。     

Quantization Noise in Digital Moving Target Indication Systems

This paper deals precisely with the effect of quantum or step size in an analog-to-digital converter on the quantization noise in the output of MTI (moving target indication) radar processors. The correlation between quantization errors on successive pulses is considered in the analysis and is shown to have a small quieting effect on the output quantization noise.     

基于系统级测量参量的红外成像仿真方法

针对新型红外成像系统的成像特性,通过对光电场景图像与系统输出图像特性的客观比较,推导了场景图像灰度到光电成像系统输出图像的灰度转换模型;首次提出了基于系统级的测量参数:SiTF、MTF、NETD、噪声等效背景照度的光电输出成像的仿真方法,并给出了仿真结果.最后现场试验验证了其合理性.     

Comments on "Optimum Bandwidth of a Low-Pass Filter for Detection of a Pulse in Nonstationary Noise"

In a recent correspondence1 a calculation of the optimum bandwidth of a low-pass RC filter for the detection of a pulse signal in nonstationary noise was presented. The purpose of this correspondence is: 1) to point out additional references to the work which has been conducted in the stationary noise case, and 2) to present an interesting alternate derivation of the expected output noise power for the nonstationary noise case.     

A multiscale transform denoising method of the bionic polarized light compass for improving the unmanned aerial vehicle navigation accuracy

In recent years, the bionic polarized light compass has been widely studied for the unmanned aerial vehicle navigation. However, it is found from the obtained investigation results that a polarized light compass with a sensitive and high dynamic range polarimeter still provides inferior output precision of the heading angle due to the presence of the noise generating from the compass.The noise is existed not only in the angle of the polarization image acquired by polarimeters but also in the out...     

Transient Nonstationary Behavior of a Delay Line Discriminator

The development of numerical methods for studying the transient nonstationary behavior of a delay line discriminator is presented. Expressions are developed for the mean and the variance of the output noise process. For the cases where the output is stationary, power density spectra are found.