变截面梁式压电智能板振动控制的小波模式

基于 Daubechies小波理论的尺度函数变换 ,对于变截面悬臂板结构的弯曲建立了由压电片感应器的观测电量识别挠曲变形构形的显式关系式。此基础上 ,采用具有位移与速度信号负反馈控制律后 ,建立了抑制振动的压电动力控制程序。由于小波尺度函数逼近具有低带通性质 ,即具有自动滤除高频分量的能力 ,该控制程序将不会出现由观测溢出与控制溢出耦合而造成的控制失稳 (即在抑制低频 (阶 )扰动时系统激发出高频 (阶 )扰动的现象 )。数值仿真结果表明 :该控制方法所能控制的模态阶数与压电片数相同 ,而且其控制程序在抑制外界干扰方面是有效的。     

智能桨叶的实时模型与复合自适应振动控制

研究了智能桨叶的实时模型、控制方法与控制器的实时实现。首先,采用MX滤波器实现了对桨叶动态特性的实时在线模拟,给出了该滤波器的系数与所描述的受控结构模态参数之间的相互关系。接着,提出了一种新的复合自适应控制方法,它综合了自适应前馈控制和反馈控制的特点,实现了对桨叶阻尼和振动响应的控制。最后,在所建立的以高速信号处理器为中心的实时数字仿真系统上,实现了对单频、双频及变频、变幅值谐和激励下桨叶振动的控制,获得了良好的振动控制效果。     

Acceleration sensors based modal identification and active vibration control of flexible smart cantilever plate

Some flexible appendages of spacecrafts, such as solar panels, are cantilever plate structures. Thus, vibration problem is unavoidable when there is slewing maneuver or external disturbance excitation. Vibration of such cantilever plate structures includes coupled bending and torsional motion. Furthermore, the low amplitude vibration near the equilibrium point is very difficult to be quickly suppressed due to nonlinear factors of the hardware in the system, which is harmful to stability and attitude control accuracy. To solve these problems, acceleration sensor-based modal identification and active vibration control methods are presented for the first two bending and the first two torsional modes vibration of the cantilever plate. Optimal placements of three acceleration sensors and PZT patches actuators are performed to decouple the bending and torsional vibration of such cantilever plate for sensing and actuating, and identifications are achieved by experiments. A nonlinear control method is presented to suppress both high and low amplitude vibrations of flexible smart cantilever plate significantly. Experimental comparison researches are conducted by using acceleration proportional feedback and the presented nonlinear control algorithms. The experimental results demonstrate that the presented acceleration sensor-based methods can suppress the vibration of cantilever plate effectively.     

压电智能反射面静态形状控制与作动器位置优化

为了提高反射面的精度,建立了压电智能反射面的形状控制模型,对该结构的力学建模方法、形状控制方法和作动器优化配置算法进行了研究。首先,将蜂窝夹层结构的压电智能反射面等效为多层复合板,根据虚功原理推导了结构的有限元方程。然后,根据建立的有限元方程,推导了反射面变形的均方根误差与作动器控制电压的关系式,以均方根误差最小为优化目标,建立了形状控制优化模型,将作动器控制电压的优化转化为约束优化问题的求解。最后,采用模拟退火算法对压电作动器进行了优化配置。为了验证形状控制的可行性及优化算法的有效性,以300mm口径的平面压电智能反射面为例进行仿真,分析结果表明,通过压电作动器的控制,可以使反射面的重力变形误差减小97%以上,对于给定数目的作动器,通过模拟退火算法优化,可使其布置在最佳的位置。     

不同振动形式下的翼型失速特性

通过求解雷诺平均Navier-Stokes方程,研究了翼型在强迫振动和自然结构振动下的大迎角流场特性,尤其是失速迎角附近的流场和气动特性.研究结果表明:在接近颤振临界速度情况下结构自然振动可以引起翼型大尺度的分离,导致失速分离涡提前出现;强迫性的沉浮运动和俯仰运动在一定幅度下也可以引起失速性质的大分离,而且沉浮和俯仰振动的频率和振幅都是影响翼型大尺度分离的重要因素.     

Dynamics of a rigid rotor in the NK-14ST-10 engine free power turbine with sliding bearings

A problem of increasing free power turbine (FPT) service life at the expense of a change to sliding bearings is considered. The differential equations for the rotor motion are derived with account for its design features. Also presented are the calculated data on forced vibrations of the system and the utility of FPT support updating is analyzed.     

基于干扰观测器的四旋翼无人机离散时间容错控制

为了飞行控制方案便于在计算机上实现，针对具有外部干扰和执行器加性故障的四旋翼无人机（UAV）角度运动方程，给出一种基于干扰观测器的离散时间跟踪控制方案。通过设计离散时间干扰观测器抑制外部干扰和执行器故障的不利影响，并结合干扰观测器设计离散时间控制器。通过数值仿真验证了基于干扰观测器的离散时间容错控制方案的有效性。仿真结果表明，设计的离散控制器能够保证外部干扰和执行器故障综合作用下的四旋翼UAV系统跟踪控制性能。     

Adaptive Integral-type Sliding Mode Control for Spacecraft Attitude Maneuvering Under Actuator Stuck Failures

A fault tolerant control (FTC) design technique against actuator stuck faults is investigated using integral-type sliding mode control (ISMC) with application to spacecraft attitude maneuvering control system. The principle of the proposed FTC scheme is to design an integral-type sliding mode attitude controller using on-line parameter adaptive updating law to compensate for the effects of stuck actuators. This adaptive law also provides both the estimates of the system parameters and external disturbances such that a prior knowledge of the spacecraft inertia or boundedness of disturbances is not required. Moreover, by including the integral feedback term, the designed controller can not only tolerate actuator stuck faults, but also compensate the disturbances with constant components. For the synthesis of controller, the fault time, patterns and values are unknown in advance, as motivated from a practical spacecraft control application. Complete stability and performance analysis are presented and illustrative simulation results of application to a spacecraft show that high precise attitude control with zero steady-error is successfully achieved using various scenarios of stuck failures in actuators.     

Sliding mode and shaped input vibration control of flexible systems

In this paper, the vibration reduction problem is investigated for a flexible spacecraft during attitude maneuvering. A new control strategy is proposed, which integrates both the command input shaping and the sliding mode output feedback control (SMOFC) techniques. Specifically, the input shaper is designed for the reference model and implemented outside of the feedback loop in order to achieve the exact elimination of the residual vibration by modifying the existing command. The feedback controller, on the other hand, is designed based on the SMOFC such that the closed-loop system behaves like the reference model with input shaper, where the residual vibrations are eliminated in the presence of parametric uncertainties and external disturbances. An attractive feature of this SMOFC algorithm is that the parametric uncertainties or external disturbances of the system do not need to satisfy the so-called matching conditions or invariance conditions provided that certain bounds are known. In addition, a smoothed hyperbolic tangent function is introduced to eliminate the chattering phenomenon. Compared with the conventional methods, the proposed scheme guarantees not only the stability of the closed-loop system, but also the good performance as well as the robustness. Simulation results for the spacecraft model show that the precise attitudes control and vibration suppression are successfully achieved.     

飞行器智能结构系统研究进展与关键问题

 飞行器智能结构是由传感器、驱动器、控制元件和基体结构组成的集成系统,它具有承载、检测、判断与动作等功能,可显著提升飞行器的性能。根据国内外飞行器智能结构系统研究的最新进展,论述了飞行器结构动力响应主动控制、智能机翼、旋翼以及飞行载荷谱监测与结构损伤诊断等的基本原理与技术问题;指出了飞行器智能结构系统研究在埋入式功能元件、复杂非线性多场耦合系统的动力学建模与控制以及智能结构系统中的损伤和失效问题等方面所面临的关键技术问题和挑战。     

Reconfigurable fault-tolerant control for supersonic missiles with actuator failures under actuation redundancy

Aircraft undergoing actuator failures into under-actuation have been seldom studied in literature. Aiming at addressing actuator failures of Total Loss of Effectiveness (TLOE) as well as Partial Loss of Effectiveness (PLOE) resulting in different system actuations, reconfigurable Fault-Tolerant Control (FTC) is proposed for supersonic wingless missiles under actuation redundancy. The under-actuated system of TLOE failure patterns is solved by transformation to cascade systems through a ‘shape variable’. Meanwhile, actuator TLOE faults of different unknown failure patterns from proper actuation to under-actuation are accommodated by a reconfigurable adaptive law on a multiple-model basis. The backstepping technique with the Extended State Observer (ESO) method adopted as a basic strategy is applied to an established symmetric coupled missile system with actuator PLOE faults, modeling errors, and external disturbances. Additionally, the nonlinear saturation characteristics of actuators are settled by an auxiliary system with the Nussbaum function technique. The stability of the control system is analyzed and proven through Lyapunov theory. Numerical simulations are implemented in the presences of aerodynamic uncertainties, gust disturbance, and actuator failures. Results demonstrate the effectiveness of the proposed method with satisfactory tracking performance and actuator fault tolerance capacity.     

压电驱动器的气动弹性应用

 随着压电智能材料与结构的发展,压电驱动器在气动弹性控制领域占据重要地位。使用压电驱动器控制翼面变形,利用而不是抵抗气动弹性效应可以控制升力、力矩以及它们的分布。采用基本相同的智能结构翼面控制系统,根据不同的控制目标需求,使用压电智能材料驱动器可以达到多种目的,包括静态的形状控制与动态的颤振抑制、抖振控制与阵风响应控制。静态控制方面例如改变翼面形状获得附加空气动力以增加升力、提供横滚力矩、改变升力分布以减小诱导阻力或减小翼根弯矩等;动态控制例如利用改变翼面形状产生的附加空气动力作为控制载荷,改变气动弹性系统的耦合程度,根据控制效果要求可作为气动阻尼、气动刚度或气动质量。这种控制方法可以减轻结构重量,提高操纵效率,扩大飞行包线,提高材料利用率,已成为可变形飞行器的重要研究内容。本文主要阐述压电驱动器气动弹性应用的动机与机理、发展与成就以及问题与展望。     

STUDIES ON AIRCRAFT TOTAL ENERGY FLIGHT CONTROL SYSTEM：NONLINEAR SYSTEM INTEGRATION AND SIMULATION

ＳＴＵＤＩＥＳＯＮＡＩＲＣＲＡＦＴＴＯＴＡＬＥＮＥＲＧＹＦＬＩＧＨＴＣＯＮＴＲＯＬＳＹＳＴＥＭ：ＮＯＮＬＩＮＥＡＲＳＹＳＴＥＭＩＮＴＥＧＲＡＴＩＯＮＡＮＤＳＩＭＵＬＡＴＩＯＮＷｕＳｈｕｆａｎ；ＳｈｅｎＹｏｎｇｚｈａｎｇ；ＧｕｏＳｕｏｆｅｎｇ（Ｄｅｐｔ...     

Vibrations of circular sandwich plates connected with an elastic foundation

The results of analyzing axisymmetric forced vibrations of an elastic circular sandwich plate connected with an elastic foundation under different surface loads are presented. The hypotheses of a broken normal are accepted to describe the kinematics of a package that is nonsymmetrical over the thickness. The analytical solutions of a problem for plates with a light filler are obtained and numerical analysis is carried out.     

变循环发动机完全分布式控制

采用分布式控制架构可以降低变循环发动机控制系统的重量并有利于系统的开发和扩展。提出了一种完全分布式控制架构,控制算法的计算完全分布到智能执行机构中,计算所需的参数值由智能传感器通过串行数据总线发送到智能执行机构。变循环发动机完全分布式控制系统研发的主要工作是设计分散控制算法和总线通信方案。将控制回路的耦合当作总扰动的一部分,使用线性自抗扰控制器(ADRC)观测并在控制信号中消除总扰动,实现了分散控制。在CAN总线硬件的基础上,使用CANaerospace高层协议设计了时间触发的总线通信方案。从而实现了变循环发动机完全分布式控制。在MATLAB/Simulink环境下使用TrueTime工具箱搭建了仿真系统。使用TrueTime Kernel模块仿真智能执行机构与智能传感器的计算单元,使用TrueTime Network模块仿真CAN总线,并且将线性ADRC和CANaerospace协议写入到计算单元中。仿真结果表明:所建立的变循环发动机完全分布式控制系统能够适应发动机进气状况和健康状况的大范围变化,具有较好的鲁棒性。     

Twistor-based synchronous sliding mode control of spacecraft attitude and position

A synchronous control of relative attitude and position is required in separated ultra-quiet spacecraft, such as drag-free, disturbance-free, and distributed spacecraft. Thus, a twistor-based synchronous sliding mode control is investigated in this paper to solve the control problem of relative attitude and position among separated spacecraft modules. The twistor-based control design and the stability proof are implemented using the Modified Rodrigues Parameter (MRP). To evaluate the effectiveness of the proposed control method, this paper presents a case study of separated spacecraft flying control considering the mass uncertainty and external disturbances. In addition, a simulation study of the Proportional-Derivative (PD) control is also presented for comparison. The results indicate that the twistor-based sliding mode controller can ensure global asymptotic stability. The states converge fast with ultra-precision and ultra-stability in both the attitude and position. Moreover, the proposed twistor-based sliding mode control system is robust to the mass uncertainty and external disturbances.     

液压仿真转台的PFC-PID串级控制

 针对三轴液压仿真转台系统难以获得精确数学模型,存在较大参数变化和各种干扰,常规控制方法难以获得良好控制效果的特点,找到一种适合三轴液压转台的预测函数控制(PFC)策略,并与PID控制相结合,提出PFC PID串级控制并应用于液压仿真转台系统。系统内回路采用PID控制克服各种干扰,内回路和液压仿真转台对象构成PFC的广义被控对象,对广义被控对象采用PFC控制拓展系统频宽,改善系统性能。对三轴液压仿真转台的仿真研究结果表明了该方法的有效性和优越性。     

Fault-tolerant control with mixed aerodynamic surfaces and RCS jets for hypersonic reentry vehicles

This paper proposes a fault-tolerant strategy for hypersonic reentry vehicles with mixed aerodynamic surfaces and reaction control systems (RCS) under external disturbances and subject to actuator faults. Aerodynamic surfaces are treated as the primary actuator in normal situations, and they are driven by a continuous quadratic programming (QP) allocator to generate torque com-manded by a nonlinear adaptive feedback control law. When aerodynamic surfaces encounter faults, they may not be able to provide sufficient torque as commanded, and RCS jets are activated to augment the aerodynamic surfaces to compensate for insufficient torque. Partial loss of effective-ness and stuck faults are considered in this paper, and observers are designed to detect and identify the faults. Based on the fault identification results, an RCS control allocator using integer linear programming (ILP) techniques is designed to determine the optimal combination of activated RCS jets. By treating the RCS control allocator as a quantization element, closed-loop stability with both continuous and quantized inputs is analyzed. Simulation results verify the effectiveness of the proposed method.     

Investigation of dynamics of discrete framed structures by a numerical wave-based method and an analytical homogenization approach

In this article, the analytical homogenization method of periodic discrete media (HPDM) and the numerical condensed wave finite element method (CWFEM) are employed to study the lon-gitudinal and transverse vibrations of framed structures. The valid frequency range of the HPDM is re-evaluated using the wave propagation feature identified by the CWFEM. The relative error of the wavenumber by the HPDM compared to that by the CWFEM is illustrated in functions of fre-quency and scale ratio. A parametric study on the thickness of the structure is carried out where the dispersion relation and the relative error are given for three different thicknesses. The dynamics of a finite structure such as natural frequency and forced response are also investigated using the HPDM and the CWFEM.     

Review of state of the art in smart rotor control research for wind turbines

This article presents a review of the state of the art and present status of active aeroelastic rotor control research for wind turbines. Using advanced control concepts to reduce loads on the rotor can offer great reduction to the total cost of wind turbines. With the increasing size of wind turbine blades, the need for more sophisticated load control techniques has induced the interest for locally distributed aerodynamic control systems with build-in intelligence on the blades. Such concepts are often named in popular terms ‘smart structures’ or ‘smart rotor control’. The review covers the full span of the subject, starting from the need for more advanced control systems emerging from the operating conditions of modern wind turbines and current load reduction control capabilities. An overview of available knowledge and up-to date progress in application of active aerodynamic control is provided, starting from concepts, methods and achieved results in aerospace and helicopter research. Moreover, a thorough analysis on different concepts for smart rotor control applications for wind turbines is performed, evaluating available options for aerodynamic control surfaces, actuators (including smart materials), sensors and control techniques. Next, feasibility studies for wind turbine applications, preliminary performance evaluation and novel computational and experimental research approaches are reviewed. The potential of load reduction using smart rotor control concepts is shown and key issues are discussed. Finally, existing knowledge and future requirements on modeling issues of smart wind turbine rotors are discussed. This study provides an overview of smart rotor control for wind turbines, discusses feasibility of future implementation, quantifies key parameters and shows the challenges associated with such an approach.