Single-phase grid-connected PV system using three-arm rectifier-inverter

A grid-connected photovoltaic (PV) power supply system with on-line voltage regulation capability is presented. It employs the three-arm rectifier-inverter topology with PV modules connected directly on the dc-link. The common-arm is with line-frequency switching and synchronous to the input voltage, aiming for a lower switching loss and decoupling the control of rectifier and inverter portions. As a result, the rectifier and inverter portions can be controlled independently with the rectifier-arm and inverter-arm, respectively. For maximum power point tracking (MPFF) of the PV modules and balancing the power among utility, PV, and the load, a variable dc-link voltage is adopted and controlled by the rectifier-arm based on the MPPT control algorithm. The inverter-arm then regulates the load voltage with good regulation and low distortion. Due to large variation of the dc-link voltage, a feedforward plus feedback control technique with variable gain is developed to keep constant bandwidth of the current loop at any operation condition. Therefore, the performance of the rectifier and inverter portions can be ensured. A system containing a 2 kVA converter and a 1.2 kW PV module is set up, and some experimental results are provided for demonstrating the effectiveness of the proposed method.     

AC/DC converter topologies for the Space Station

A new class of AC/DC converter topologies (Type-1 converters) is described, suitable for use in an advanced single-phase sine-wave voltage, high-frequency power distribution system, of the type that was proposed for a 20 kHz Space Station primary electrical power distribution system. The converter comprises a transformer, a resonant network, a current controller, a diode rectifier, and an output filter. The input AC voltage source is converted into a sinusoidal current source using the resonant network. The output of this current source is rectified by the diode rectifier and is controlled by the current controller. The controlled rectified current is then filtered by the output filter to obtain a constant voltage across the load. Three distinct converter topologies, Type-1A, Type-1B, and Type 1-C, are described, and their performance characteristics are presented. All three types have a close-to-unity rated power factor (greater than 0.98), low total harmonic distortion in input current (less than 5%), and high conversion efficiency (greater than 96%)     

ZCS-PWM boost rectifier with high power factor and low conduction losses

A new single-phase high power factor rectifier is proposed, which features regulation by conventional pulsewidth modulation (PWM), soft commutation, and instantaneous average line current control. A new zero-current-switching PWM (ZCS-PWM) auxiliary circuit is configured in the presented ZCS-PWM rectifier to perform ZCS in the switches and zero-voltage-switching (ZVS) in the diodes. Furthermore, soft commutation of the main switch is achieved without additional current stress by the presented ZCS-PWM auxiliary circuit. A significant reduction in the conduction losses is achieved, since the circulating current for the soft switching flows only through the auxiliary circuit and a minimum number of switching devices are involved in the circulating current path and the proposed rectifier uses a single converter instead of the conventional configuration composed of a four-diode front-end rectifier followed by a boost converter. Seven transition states for describing the behavior of the ZCS-PWM rectifier in one switching period are described. The PWM switch model is used to predict the system performance. A prototype rated at 1 kW, operating 60 kHz, with an input ac voltage of 220 V/sub rms/ and an output voltage 400 V/sub dc/ has been implemented in laboratory. An efficiency of 97.2% and power factor near 0.99 has been measured. The analysis and design of the control circuitry are also presented.     

Frequency-controlled series-resonant converter with synchronous rectifier

This paper presents an analysis and experimental results for a frequency-controlled series-resonant dc-dc converter that consists of a Class-D zero-voltage-switching (ZVS) series-resonant inverter and a center-tapped synchronous rectifier. If the dc output voltage is low, the efficiency of the converter is dominated by the efficiency of the rectifier. Low on-resistance metal-oxide-semiconductor field-effect transistors (MOSFETs) are used in the rectifier instead of diodes because the forward voltage drop across the rectifying device is low, resulting in a high efficiency. The dc output voltage is regulated against variations in the load resistance and the dc input voltage by varying the operating frequency. Experimental results are presented for a converter with a dc input voltage of 150 V, an output voltage of 5 V, and a dc load resistance ranging from 0.5 to 5.5 R. The measured efficiency was 86% for a 50 W output and 89% for a 25 W output. The theoretical results were in good agreement with the measured results.     

Soft-switching single-stage AC-to-DC converter with low harmonic distortion

A 1 /spl phi/ high-frequency (HF) transformer isolated, soft-switching single-stage ac-dc converter with low line-current harmonic distortion is presented. Its operation is explained with equivalent circuits for the various intervals. The converter is analyzed and design curves are obtained. An optimization parameter is introduced and a systematic design procedure is illustrated with a design example. Detailed SPICE simulation and experimental results of a 500 W converter with load as well as line voltage variation are given to verify theory. The proposed converter employs a zero-voltage transition (ZVT) network to ensure zero-voltage switching (ZVS) at all loads, and natural power factor correction is ensured using a simple control circuit.     

集成低频脉冲功率解耦端口的机载电源系统

为了消除高峰均功率比低频脉冲负载对有限容量机载交流供电系统的周期性冲击等不利影响,对开关器件进行集成和复用,提出了能够同时提供功率解耦端口和直流输出端口的三端口功率解耦整流器。通过将三端口整流器与DC/DC变换器组合,构造出集成低频脉冲功率解耦端口的机载电源系统,实现了直流侧周期性脉动功率和交流源侧功率的解耦,并保证低频脉冲负载正常供电需求。详细分析了三端口整流器的工作原理,提出了与之相适应的功率控制方法和调制策略,基于开关器件分时复用原理,实现了交流端口到两个直流端口的功率传输和分配,并实现了两个直流端口功率切换过程的平滑过渡。实验结果验证了所提三端口脉冲功率解耦整流器的有效性和可行性。     

Single-phase power-factor-correction AC/DC converters with threePWM control schemes

Three pulse-width modulation (PWM) control schemes for a single-phase power-factor-correction (PFC) AC/DC converter are presented to improve the power quality. A diode bridge with two power switches is employed as a PFC circuit to achieve a high power factor and low line current harmonic distortion. The control schemes are based on look-up tables with hysteresis current controller (HCC) to generate two-level or three-level PWM on the DC side of diode rectifier. Based on the proposed three control schemes, the line current is driven to follow the sinusoidal current command which is in phase with the supply voltage, and two capacitor voltages on the DC bus are controlled to be balanced. The simulation and experimental results of a 1 kW converter with load as well as line voltage variation and shown to verify the proposed control schemes. It is shown that unity PFC is achieved using a simple control circuit and the measured line current harmonics satisfy the IEC 1000-3-2 requirements     

A resonant DC-DC transformer

The characteristics of a push-pull parallel resonant converter (PPRC) when operated as a DC-DC transformer were investigated theoretically and experimentally. In the DC-DC transformer region, the voltage transfer ratio of the PPRC was found to be practically constant and independent of the input voltage and load. In this mode, all the switching elements operate in the zero voltage switching (ZVS) condition. Another important feature of the proposed DC-DC transformer is the ability to drive it by an arbitrary switching frequency, provided that the latter is lower than the self-oscillating frequency. This permits the synchronization of the converter to a master clock. The analytical expressions for voltage and current stresses, as well as the other key parameters derived, are applied to develop design guidelines for the DC-DC transformer. The proposed topology was tested experimentally on a 100-W unit which was run in the 200-kHz frequency region     

Implementation of a single-phase AC/AC converter based on neutral-point-clamped topology

A single-phase ac/ac converter based on neutral-point-clamped scheme is proposed to perform unity input power factor and to provide a stable ac voltage to the critical loads. The ac/dc rectifier part is controlled to generate a unipolar pulsewidth modulation (PWM) waveform on the ac terminal by using four power switches with voltage stress of half the dc-link voltage. The carrier-based current control scheme is employed in the inner control loop to track the line current command. To regulate the dc bus voltage, a proportional-integral (PI) control is adopted in the outer control loop. The dc/ac inverter part of the system with four power switches is employed to generate a stable and clean sinusoidal output voltage to the critical load. The instantaneous current control scheme is used to track the output voltage command. To verify the effectiveness of the proposed control algorithm, the simulation and experimental results based on a laboratory prototype were implemented and discussed.     

三相电压型脉宽调制整流器定频模型预测控制

针对三相电压型脉宽调制(PWM)整流器有限控制集模型预测控制采样频率高、开关频率不固定的缺点,提出了一种定频模型预测控制方法。通过求解价值函数得到PWM整流器交流侧下一采样时刻所要输出的电压值,利用空间矢量脉宽调制技术输出计算得到的电压值,实现定频模型预测控制。仿真与试验结果表明:所提出的控制算法开关频率恒定,稳态电流谐波含量低,实现了整流器高功率因数运行。     

Half-bridge neutral point diode clamped rectifier for power factor correction

A high power factor rectifier based on neutral point clamped scheme is proposed. The voltage stress of each power semiconductor of the adopted rectifier is equal to the half dc bus voltage instead of full dc link voltage in the conventional switching mode rectifier. The control signals of the power switches are derived from the dc link voltage balance compensator, line current controller, and dc link voltage regulator. The hysteresis current control scheme is employed to draw a clean sinusoidal line current, high input power factor, regulated dc link voltage, and balance capacitor voltages. Three voltage levels are generated on the ac terminal of the adopted rectifier. To verify the proposed operation scheme, performance characteristics are given by the experimental results.     

航空机电作动器的混合整流全状态反馈控制

研究了一种适用于多电飞机供电系统的新型混合整流电路,并针对航空机电作动器负载特殊的用电特性,提出了一种基于全状态反馈的混合整流控制方法,在保证整流效果的同时,解决了负载功率短时大范围变化引起的直流电压不稳定问题。这种新型混合整流电路将二极管整流电路和脉宽调制(PWM)整流电路并联输出接负载,两者共同承担有功功率且比例可控,通过适当控制PWM电路达到网侧低谐波的目的,且当负载制动时,能量可以回馈交流侧电网。建立了混合整流器的线性化全状态数学模型,设计了基于线性二次型(LQR)最优化理论的全状态反馈控制策略。通过在MATLAB/Simulink下的建模与仿真,比较了全状态反馈控制方法与传统三状态反馈控制方法,并在机电作动器样机上进行了实验验证。仿真和实验结果表明,采用全状态反馈控制的新型混合整流方案对于功率大范围变化负载具有更好的控制性能。     

单端正激ZVT功率变换器实现

介绍一种单端正激工作方式的零电压过渡（ＺＶＴ）软开关ＤＣ－ＤＣ变换器;描述该变换器的原理和特征;给出了应用ＺＶＴ软开关技术和集成控制块ＳＧ３５２５Ａ的２４Ｖ／９ＡＤＣ－ＤＣ变换器电路和实验结果。     

High power factor AC/DC/AC converter with random PWM

A three-phase AC/DC/AC converter is presented with a power factor preregulator to improve the power quality in the input side and a pseudorandom noise generator to reduce the emitted acoustic noise and the mechanical vibration for an induction motor drive. The space vector modulation with hysteresis current control for a voltage source rectifier is adopted to simplify the hardware circuit. A control scheme is presented to drive the supply current following the reference current. The amplitude of reference current for the pulsewidth modulation (PWM) rectifier is derived from the DC bus voltage regulator and the estimated output power. Random switching frequency technique for a three-phase PWM inverter system to reduce the annoying tonal noise and resonant vibration from an induction motor is described. By randomly varying the instantaneous PWM switching frequency from one cycle to the next, the frequency distribution of harmonics is spread in a wide frequency range. The major advantage for using such a strategy is the nonrepetitive output spectral characteristic that results in reduction of torque pulsations in motor drive systems. The nearly unity power factor at the three-phase rectifier and the absence of acoustic noise concentrated at the specific tones which is usually present with conventional sinusoidal modulation are verified by the experimental tests     

Steady-State Analysis of the Series Resonant Converter

The series resonant converter is analyzed in steady state, and for constant switching frequency the output current and voltage characteristics are found to be ellipses. The converter operating point can then be easily obtained by superimposing a load line on these elliptical characteristics. Peak resonant capacitor voltage and inductor current are also plotted in the output plane and are dependent to first order only on output current. When peak voltage and current are plotted in this manner, the dependence of component stresses on operating point is clearly revealed. The output characteristics are modified to include the effect of transistor and diode voltage drops, and experimental verification is presented.     

Implementation of nondeterministic pulsewidth modulation forinverter drives

A single-phase power factor preregulator to improve the power quality in the input side of an ac/dc/ac converter and a random pulsewidth modulation (PWM) to reduce the emitted noise energy and the mechanical vibration for an induction motor drive is proposed. The hysteresis current control (HCC) technique for a voltage source switching mode rectifier (SMR) is adopted. A control scheme is presented such that the line current is driven to follow the reference current which is derived from the dc bus voltage regulator and the output power estimator. A random pulse position technique for a three-phase voltage source inverter system to reduce the noise energy and resonant vibration from ac machine drive is described. By randomly varying the instantaneous pulse position in each switching frequency, the frequency distribution of harmonics is spread in a wide frequency range which results in reduction of torque pulsations in the ac motor drive systems. To investigate the proposed control scheme, experimental tests based on a laboratory prototype were implemented to show the nearly unity power factor at the SMR and reduce the noise energy concentrated at the specific tones     

Three-phase single-stage ac/dc boost integrated series resonant converter

A new ac/dc 3-/spl phi/ single-stage converter is proposed integrating a 3-/spl phi/ discontinuous current mode (DCM) boost with a dc/dc fixed frequency series resonant converter (SRC). This converter has the following features: natural power factor correction, soft switching, high-frequency (HF) transformer isolation with the series resonant tank operating in above resonance mode, etc. A new complementary gating control scheme is used for simultaneous control of boost converter and the SRC. Modes of operation are presented and analyzed. Based on the analysis, design curves are obtained. An optimum design is given and a design example is presented. Results obtained from SPICE simulation for the designed converter are given to verify the performance of the proposed converter for varying load as well as line voltage. Experimental results obtained from a laboratory prototype converter are presented to verify the theory.     

Flyback Converter Output Voltage Stabilization

The expression of the flyback converter output voltage (output power) is derived as a function of the supply voltage, load resistance, transformer ratios, transistor current gain, and base-circuit resistor value. Switching period and duty cycle are also calculated. A converter circuit is designed having stabilized output voltage, with respect to supply voltage, at constant load. The transistor base current is controlled by the supply voltage, via a nonlinear circuit. This feedforward circuit approximates with logarithmic characteristics the ideal hyperbolic dependence of the transistor base current as a function of the supply voltage. The converter has high performance and low cost. A cheaper circuit variant is presented, in which the high-voltage control transistor was eliminated.     

Suitability of pulse train control technique for BIFRED converter

Pulse Train/spl trade/ control scheme is presented and applied to a boost integrated flyback rectifier/energy storage dc-dc (BIFRED) converter operating in discontinuous conduction mode (DCM), which avoids the light-load high-voltage stress problem. In contrast to the conventional control techniques, the principal idea of Pulse Train technique is to regulate the output voltage using a series of high and low energy pulses generated by the current of the inductor. The applicability of the proposed technique to both the input and magnetizing inductances of BIFRED converter is investigated. Analysis of BIFRED converter operating in DCM as well as the output voltage ripple estimation is given. Experimental results on a prototype converter are also presented.     

Fourier theory of jumps applied to converter harmonic analysis

The Fourier theory of jumps (FTJ) is demonstrated as an aid in deriving closed-form analytical equations for converter switching harmonics. The switching waveforms analyzed are the input current and output voltage and current of a three-phase, ac-dc, step-down, dead-band pulsewidth modulated (PWM), unity power factor converter. The input current closed-form harmonic equation is derived for two parallel-connected, interleaved-PWM converters supplying the same load and sharing a common input filter. The equations are compared with PSpice^TM simulations and practical results