具有多层试验数据的成败型元件之串并联系统及并串联系统可靠性置信下限的近似解

设系统A由K个独立的子系统B_1,B_2,…,B_K并(串)联而成,设第i个子系统B_i又由m_i个相互独立的成败型元件C_(i1),C_(i2),…C_(imi)串(并)联而成,设有多层试验数据: 元件C_(ij)试验N_(ij)次,成功S_(ij)次,失败F_(ij)次(i=1,2,…,K,j=1,2,…,m_i) 子系统B_i有成败型试验数据:试验N_i次,成功S_i次,失败F_i次(i=1,2,…,K) 系统A有成败型试验数据:试验N次,成功S次,失败F次。 本文给出利用此多层成败型试验数据,求系统A的可靠性置信下限的近似解的方法,本文利用一、二阶矩拟合的原则将上述数据折合为原系统A的伪成败型数据:伪试验数N~*,伪成功数S~*,然后从N~*,S~*出发利用单个成败型元件之可靠性的经典精确方法求出原系统A的可靠性置信下限的近似值。本文推导了伪试验数N~*,伪成功数S~*的计算公式,并给出了计算实例。     

利用搜索法对嫦娥三号着陆器和巡视器定位

针对嫦娥三号巡视器相对定位时同波束甚长基线干涉测量（VLBI）差分相位时延存在纳秒量级模糊度的问题,提出利用搜索法对巡视器和着陆器的相对位置进行确定,并将该方法应用于着陆器的绝对位置的确定。首先介绍对嫦娥三号着陆器和巡视器测量的模式以及定位的原理,然后进行相应定位计算。利用该方法对着陆器定位结果与统计定位法结果比较,位置差100m左右,与月球勘测轨道飞行器（LRO）航拍定位结果差异在75m;该方法对巡视器在各停泊点的相对定位结果,与统计定位结果比较,位置差小于1m。     

CELSS nutrition system utilizing snails

At the 40th IAF Congress in Malaga, a nutrition system for a lunar base CELSS was presented. A lunar base with a total of eight crew members was envisaged. In this paper, four species of plants--rice, soybean, lettuce and strawberry--were introduced to the system. These plants were sufficient to satisfy fundamental nutritional needs of the crew members. The supply of nutrition from plants and the human nutritional requirements could almost be balanced. Our study revealed that the necessary plant cultivation area per crew member would be nearly 40 m3 in the lunar base. The sources of nutrition considered in the study were energy, sugar, fat, amino acids, inorganic salt and vitamins; however, calcium, vitamin B2, vitamin A and sodium were found to be lacking. Therefore, a subsystem to supply these elements is of considerable value. In this paper, we report on a study for breeding snails and utilizing meat as food. Nutrients supplied from snails are shown to compensate for the above mentioned lacking elements. We evaluate the snail breeder and the associated food supply system as a subsystem of closed ecological life support system.     

柔性空间机械臂的自适应H∞容错抑振混合控制

针对关节执行器存在部分失效(PLCE)故障的漂浮基柔性空间机械臂系统，提出一种自适应H∞容错抑振混合控制算法。结合拉格朗日法与弹性振动理论推导出了系统的动力学微分方程，并截取反映柔性臂杆主振型的前两阶模态作振动分析。根据奇异摄动原理对系统进行降维，并将其分解为一个刻画刚性臂杆轨迹跟踪的慢变子系统与一个刻画柔性臂杆模态振动的快变子系统；由此设计了由慢变子系统的自适应H∞容错控制器及快变子系统的线性最优减振控制器组成混合控制器。与传统容错控制器相比，所设计的自适应H∞容错控制器具有无需获取故障先验知识的优点。对比仿真结果表明：慢变子系统的容错控制器对于PLCE型关节执行器故障具备较强的鲁棒性，快变子系统的线性最优减振控制器能够将柔性臂杆的振动模态调节至较低水平，从而校验了理论分析的正确性与混合控制策略的有效性。     

真空羽流试验设备的负压液氮系统设计

真空羽流试验设备用于发动机真空羽流效应试验研究,同时兼顾卫星等热真空试验,对液氮系统有特殊要求。针对低至70 K液氮温度需求,设计一种全新的负压液氮系统,即利用液氮在负压下具有比常压液氮更低的饱和温度,来获得比常压液氮系统更低的液氮温度。该负压液氮系统主要由液氮输送子系统、常压过冷器子系统、负压抽气子系统、液氮泵子系统、热沉子系统及排放子系统组成,其中常压过冷器子系统和负压抽气子系统构成"负压过冷器",具有常压过冷器功能,供液温度可调,可为热沉提供70~77 K液氮制冷,满足发动机羽流及卫星热真空试验需求。     

RF communications subsystem for the Radiation Belt Storm Probes mission

The NASA Radiation Belt Storm Probes (RBSP) mission, currently in Phase B, is a two-spacecraft, Earth-orbiting mission, which will launch in 2012. The spacecraft's S-band radio frequency (RF) telecommunications subsystem has three primary functions: provide spacecraft command capability, provide spacecraft telemetry and science data return, and provide accurate Doppler data for navigation. The primary communications link to the ground is via the Johns Hopkins University Applied Physics Laboratory's (JHU/APL) 18 m dish, with secondary links to the NASA 13 m Ground Network and the Tracking and Data Relay Spacecraft System (TDRSS) in single-access mode. The on-board RF subsystem features the APL-built coherent transceiver and in-house builds of a solid-state power amplifier and conical bifilar helix broad-beam antennas. The coherent transceiver provides coherency digitally, and controls the downlink data rate and encoding within its field-programmable gate array (FPGA). The transceiver also provides a critical command decoder (CCD) function, which is used to protect against box-level upsets in the C&DH subsystem. Because RBSP is a spin-stabilized mission, the antennas must be symmetric about the spin axis. Two broad-beam antennas point along both ends of the spin axis, providing communication coverage from boresight to 70°. An RF splitter excites both antennas; therefore, the mission is designed such that no communications are required close to 90° from the spin axis due to the interferometer effect from the two antennas. To maximize the total downlink volume from the spacecraft, the CCSDS File Delivery Protocol (CFDP) has been baselined for the RBSP mission. During real-time ground contacts with the APL ground station, downlinked files are checked for errors. Handshaking between flight and ground CFDP software results in requests to retransmit only the file fragments lost due to dropouts. This allows minimization of RF link margins, thereby maximizing data rate and thus data volume.     

液体火箭发动机诊断知识挖掘系统设计

基于对液体火箭发动机的试验与故障诊断现状分析,设计了液体火箭发动机故障诊断知识挖掘系统DKMS,以实现试车数据的全面管理和故障诊断知识的高效提取。该系统采用C/S结构,分为数据采集子系统、试车数据管理子系统和诊断知识挖掘子系统三大部分。DKMS系统的设计为克服发动机故障诊断知识获取的瓶颈提供了一条新的途径。     

Design and implementation of the GPS subsystem for the Radio Aurora eXplorer

This paper presents the design and implementation of the Global Positioning System (GPS) subsystem for the Radio Aurora eXplorer (RAX) CubeSat. The GPS subsystem provides accurate temporal and spatial information necessary to satisfy the science objectives of the RAX mission. There are many challenges in the successful design and implementation of a GPS subsystem for a CubeSat-based mission, including power, size, mass, and financial constraints. This paper presents an approach for selecting and testing the individual and integrated GPS subsystem components, including the receiver, antenna, low noise amplifier, and supporting circuitry. The procedures to numerically evaluate the GPS link budget and test the subsystem components at various stages of system integration are described. Performance results for simulated tests in the terrestrial and orbital environments are provided, including start-up times, carrier-to-noise ratios, and orbital position accuracy. Preliminary on-orbit GPS results from the RAX-1 and RAX-2 spacecraft are presented to validate the design process and pre-flight simulations. Overall, this paper provides a systematic approach to aid future satellite designers in implementing and verifying GPS subsystems for resource-constrained small satellites.     

一种用于空间机械臂的 微重力模拟悬吊配重试验系统

空间机械臂工作在空间微重力环境中,广泛用于太空中的舱段对接、在轨维修等操作,因此需要在地面模拟微重力环境以满足空间机械臂研制试验要求。文章基于国内外模拟微重力环境领域技术现状,依据型号研制试验要求,提出了一种用于大型空间机械臂性能和可靠性验证的微重力环境模拟悬吊配重试验系统,并给出了悬挂机构子系统、二维随动子系统、恒拉力子系统、位姿测定子系统的设计思路和具体方案。     

YH－F1仿真系统中的信息管理子系统

ＹＨ－Ｆ１仿真系统中的信息管理子系统，为ＹＨ－Ｆ１仿真系统增加了汉化功能。其优点在于对仿真试验的输入输出信息全面管理，运载火箭控制系统仿真试验证实了该子系统的仿真效果。     

空间站有效载荷真空支持系统方案评述

有效载荷真空支持系统是空间有效载荷支持系统的重要组成部分,为空间有效载荷实验的顺利进行提供真空环境支持和保证。文章详细分析了国际空间站包括美国“命运号”实验舱（USL）、欧空局哥伦布轨道舱（APM）及日本实验舱（JEM）内的有效载荷真空支持系统方案及使用情况;对美国实验舱内的一号微重力材料科学机柜及微重力燃烧科学机柜内部专用的真空支持系统作了主要介绍;最后提出了我国空间站有效载荷真空支持系统的初步方案设想,即合理安排有效载荷实验进行次序,将废气排放子系统及真空资源子系统合二为一,以节约资源,提高可靠性。     

基于神经网络的机动飞行器自适应控制方法

针对机动飞行器强耦合性、快时变性以及高不确定性的问题,建立了六自由度刚体运动数学模型,按照时间尺度将姿态运动模型分为快变子系统和慢变子系统并分别设计动态逆控制律。然后给出了神经网络自适应控制器的设计方法,对神经网络的逆误差补偿原理、输入的选择、权值矩阵更新规则进行分析。通过算例进行六自由度仿真,证明本文方法的跟踪精度较高。     

直接力/气动力拦截弹复合逻辑与复合控制系统设计

以大气层内拦截弹直接侧向力和气动力的复合控制系统为研究对象,首先设计了轨控复合控制逻辑,然后建立了复合控制模型,并将复合系统分解为直接侧向力子系统和气动力子系统,用经典控制理论设计了气动力子系统,用模糊控制理论设计了直接力子系统。仿真结果表明:所设计的复合控制逻辑合理;基于模糊逻辑的直接力子系统可有效避免点燃发动机数量过多而需要反向点火情况的发生;与气动力系统相比,复合控制系统性能有较大提高。     

SOLID3: a multiplex antibody microarray-based optical sensor instrument for in situ life detection in planetary exploration

The search for unequivocal signs of life on other planetary bodies is one of the major challenges for astrobiology. The failure to detect organic molecules on the surface of Mars by measuring volatile compounds after sample heating, together with the new knowledge of martian soil chemistry, has prompted the astrobiological community to develop new methods and technologies. Based on protein microarray technology, we have designed and built a series of instruments called SOLID (for "Signs Of LIfe Detector") for automatic in situ detection and identification of substances or analytes from liquid and solid samples (soil, sediments, or powder). Here, we present the SOLID3 instrument, which is able to perform both sandwich and competitive immunoassays and consists of two separate functional units: a Sample Preparation Unit (SPU) for 10 different extractions by ultrasonication and a Sample Analysis Unit (SAU) for fluorescent immunoassays. The SAU consists of five different flow cells, with an antibody microarray in each one (2000 spots). It is also equipped with an exclusive optical package and a charge-coupled device (CCD) for fluorescent detection. We demonstrated the performance of SOLID3 in the detection of a broad range of molecular-sized compounds, which range from peptides and proteins to whole cells and spores, with sensitivities at 1-2?ppb (ng?mL?1) for biomolecules and 10? to 103 spores per milliliter. We report its application in the detection of acidophilic microorganisms in the Río Tinto Mars analogue and report the absence of substantial negative effects on the immunoassay in the presence of 50?mM perchlorate (20 times higher than that found at the Phoenix landing site). Our SOLID instrument concept is an excellent option with which to detect biomolecules because it avoids the high-temperature treatments that may destroy organic matter in the presence of martian oxidants.     

GPS-based relative navigation for the Proba-3 formation flying mission

The primary objective of the Proba-3 mission is to build a solar coronagraph composed of two satellites flying in close formation on a high elliptical orbit and tightly controlled at apogee. Both spacecraft will embark a low-cost GPS receiver, originally designed for low-Earth orbits, to support the mission operations and planning during the perigee passage, when the GPS constellation is visible. The paper demonstrates the possibility of extending the utilization range of the GPS-based navigation system to serve as sensor for formation acquisition and coarse formation keeping. The results presented in the paper aim at achieving an unprecedented degree of realism using a high-fidelity simulation environment with hardware-in-the-loop capabilities. A modified version of the flight-proven PRISMA navigation system, composed of two single-frequency Phoenix GPS receivers and an advanced real-time onboard navigation filter, has been retained for this analysis. For several-day long simulations, the GPS receivers are replaced by software emulation to accelerate the simulation process. Special attention has been paid to the receiver link budget and to the selection of a proper attitude profile. Overall the paper demonstrates that, despite a limited GPS tracking time, the onboard navigation filter gets enough measurements to perform a relative orbit determination accurate at the centimeter level at perigee. Afterwards, the orbit prediction performance depends mainly on the quality of the onboard modeling of the differential solar radiation pressure acting on the satellites. When not taken into account, this perturbation is responsible for relative navigation errors at apogee up to 50 m. The errors can be reduced to only 10 m if the navigation filter is able to model this disturbance with 70% fidelity.     

Development of hall thruster propulsion system for STSAT-3 application

Science and technology satellite-3 (STSAT-3) is being developed and is scheduled for launch in 2011. One of the primary objectives of its mission is to verify the performance of a hall thruster propulsion system (HPS) that uses xenon gas. According to its major functions, the HPS can be divided into several sub-modules. This paper presents the development and qualification of the hall effect thruster propulsion subsystem that includes a xenon feed system (XFS). The xenon feed system regulates the pressure down from the xenon propellant tank and supplies the xenon flows to the anode and cathode. The technology and xenon feed system developed for the STSAT-3 spacecraft will also be applicable to a variety of future electronic propulsion systems and micro-satellites. Details related to the overall development and performance results of the HPS are presented in this paper.     

摇摆软管低温疲劳试验关键技术研究

为有效考核液体火箭发动机的工作可靠性,需要通过地面试验验证摇摆软管低温疲劳特性。摇摆软管低温疲劳试验系统承担试验时涉及的摇摆环境模拟、低温压力环境模拟、轴压平衡等关键技术。摇摆驱动分系统利用水平放置的2个液压伺服油缸作为驱动单元驱动十字轴带动摇摆软管摆动,模拟摇摆软管的安装边界及摇摆工况。低温压力供应分系统向摇摆软管内腔输送一定压力的液氮,模拟摇摆软管低温以及内压环境。内压平衡子系统通过设置在摇摆软管内的轴压平衡装置平衡内腔压力产生的轴向载荷,避免在内腔压力作用下伸长。某型氧化剂摇摆软管低温疲劳试验结果表明:摇摆软管低温疲劳试验系统能够实现摇摆软管双向摇摆和单向摇摆等疲劳试验工况,试验环境和边界条件与摇摆软管实际工作状态基本一致,试验参数满足要求。     

基于FPGA的天线控制系统设计

介绍一种基于 FPGA(Field Program mable Gate Array)的共轴式双旋翼无人驾驶直升机遥测遥控数字引导的天线控制系统的设计方案 ,讨论其总线控制、步进电机控制、输入信号处理模块的设计思路及关键技术。该系统经过设计、布线、仿真测试 ,并应用于某型号无人驾驶直升机     

Plastic Cubesat: An innovative and low-cost way to perform applied space research and hands-on education

This paper describes the design and the manufacturing of a Cubesat platform based on a plastic structure.The Cubesat structure has been realized in plastic material (ABS) using a “rapid prototyping” technique. The “rapid prototyping” technique has several advantages including fast implementation, accuracy in manufacturing small parts and low cost. Moreover, concerning the construction of a small satellite, this technique is very useful thanks to the accuracy achievable in details, which are sometimes difficult and expensive to realize with the use of tools machine. The structure must be able to withstand the launch loads. For this reason, several simulations using an FEM simulation and an intensive vibration test campaign have been performed in the system development and test phase. To demonstrate that this structure is suitable for hosting a complete satellite system, offering innovative integrated solutions, other subsystems have been developed and assembled.Despite its small size, this single unit (1U) Cubesat has a system for active attitude control, a redundant telecommunication system, a payload camera and a photovoltaic system based on high efficiency solar cells.The developed communication subsystem has small dimensions, low power consumption and low cost. An example of the innovations introduced is the antenna system, which has been manufactured inside the ABS structure. The communication protocol which has been implemented, the AX.25 protocol, is mainly used by radio amateurs. The communication system has the capability to transmit both telemetry and data from the payload, in this case a microcamera.The attitude control subsystem is based on an active magnetic system with magnetorquers for detumbling and momentum dumping and three reaction wheels for fine control. It has a total dimension of about 50×50×50 mm. A microcontroller implements the detumbling control law autonomously taking data from integrated magnetometers and executes pointing maneuvers on the basis of commands received in real time from ground.The subsystems developed for this Cubesat have also been designed to be scaled up for larger satellites such as 2U or 3U Cubesats. The additional volume can be used for more complex payloads. Thus the satellite can be used as a low cost platform for companies, institutions or universities to test components in space.     

嫦娥一号卫星控制分系统地面测试系统设计

卫星控制分系统地面测试系统的设计是分系统设计的重要部分,文章介绍了应用于我国首颗月球探测器——嫦娥一号卫星的控制分系统地面测试系统的设计组成,该系统组成复杂,具有较强的可扩展性和二次开发能力,为卫星控制系统测试设备的系列化、通用化及标准化提供了一个有效的途径,其系列产品可以应用于相应的中低轨道卫星的控制分系统测试。