GPS code and carrier multipath mitigation using a multiantennasystem

Multipath is a major source of error in high precision Global Positioning System (GPS) static and kinematic differential positioning. Multipath accounts for most of the total error budget in carrier phase measurements in a spacecraft attitude determination system. It is a major concern in reference stations, such as in Local Area Augmentation Systems (LAAS), whereby corrections generated by a reference station, which are based on multipath corrupted measurements, can significantly influence the position accuracy of differential users. Code range, carrier phase, and signal-to-noise (SNR) measurements are all affected by multipath, and the effect is spatially correlated within a small area. In order to estimate and remove code and carrier phase multipath, a system comprising a cluster of five GPS receivers and antennas is used at a reference station location. The spatial correlation of the receiver data, and the known geometry among the antennas, are exploited to estimate multipath for each satellite in each antenna in the system. Generic receiver code and carrier tracking loop discriminator functions are analyzed, and relationships between receiver data, such as code range, carrier phase, and SNR measurements, are formulated and related to various multipath parameters. A Kalman filter is described which uses a combination of the available information from the antennas (receivers) in the multiantenna cluster to estimate various multipath parameters. From the multipath parameters, the code range and carrier phase multipath is estimated and compensated. The technique is first tested on simulated data in a controlled multipath environment. Results are then presented using field data and show a significant reduction in multipath error     

局域增强系统级联双频平滑技术研究(英文)

针对电离层误差时间梯度和空间梯度对局域增强系统的不利影响,提出使用级联双频平滤波方法解决此问题。级联双频平滤波先使用一个双频平滑滤波器精确估计电离层误差,利用得到的估计值修正码伪距观测量中的电离层误差,再使用一个双频平滑滤波器削弱噪声。这样,电离层误差被完全从平滑过程中移出,由L2码观测量引入的附加的噪声也被压制。基于中国民航新航行系统实验室的局域增强系统测试平台所采集的数据对级联双频平滤波的有效性和基于级联双频平滤波的局域增强系统的精度进行了分析。结果表明级联双频平滤波技术可以同时消除电离层误差时间梯度和空间梯度导致的平滑滤波残差和差分校正残差,并具有较低的滤波噪声。     

Multipath mitigation method based on Gaussian mixture model in RF relative measurement

Radio Frequency (RF) technology represents a high-precision relative navigation solution that has significant potential for application to earth-orbiting satellites. In precision applications, multipath errors dominate the total error because observables, which are used to estimate carrier-phase integer ambiguity, are not always subject to a Gaussian distribution when dual-frequency ambiguity estimation methods are used in the presence of multipath. As it has been shown that ranging observables obey a Gaussian mixture distribution, this study proposes improvements to the accuracy of estimation based on multipath mitigation founded on the Gaussian mixture model. To this end, such a model is created for integer ambiguity resolution in the presence of multipath, using which the theoretical error in dual-frequency ambiguity estimation is derived. Expectation Maximization (EM), which aids dual-frequency ambiguity estimation, is subsequently proposed to reduce the effect of multipath errors. Finally, two experimental scenarios are implemented to test the performance of the proposed method. The results show that EM-aided dual-frequency ambiguity estimation reduces the range error to approximately 20% in comparison with simple dual-frequency ambiguity estimation. Therefore the proposed technique is effective for multipath mitigation in RF relative measurement.     

雷达低空目标俯仰角跟踪的C2算法研究

在单脉冲测角体制下,由于多径回波信号的干扰,极大地降低了雷达低空目标仰俯角跟踪精度,甚至丢失目标。通过对多路径反射环境模型分析,得出了岸、海基单脉冲雷达低空目标跟踪时仰俯角测量误差的产生原因,提出将传统的多目标分辨算法(C2算法)应用于低角多径环境下目标俯仰角的跟踪测量,并在不同多径反射环境下对不同高度、不同飞行速度和飞行方向的目标进行了仿真,得到良好的仿真结果,表明该算法可较大地提高俯仰角跟踪测量精度。通过对仿真结果的分析,验证了该算法在低空目标跟踪中的有效性和可行性。     

电离层对单频卫星导航系统伪距差分定位的影响

用计算机仿真方法 ,给出了单频卫星导航系统伪距差分后 ,定位误差受电离层影响的一些结果。伪距差分定位能够校正电离层时延误差 ,但校正精度随用户与基准站到同一颗卫星倾斜因子的不同而不同。为此 ,提出了一种改进的伪距差分方法。仿真结果表明 ,改进后有明显效果     

载波相位平滑伪距在GPS/SINS紧组合导航系统中的应用

针对GPS/SINS紧组合导航系统中伪距噪声大从而引起组合导航系统精度低的问题,提出了将载波相位平滑伪距方法引入到组合导航系统中,利用具有较高精度的载波相位对低精度伪距进行平滑滤波,在建立观测方程的同时,为了减小Kalman滤波器计算量,选用最佳4颗卫星的伪距与伪距率作为观测值,并提出了一种四面体选星法,该方法不需要进行矩阵求逆运算,减小了运算量。利用光纤陀螺捷联惯导系统与GPS接收机搭建了实验验证系统,通过车载实验对所提出的方法进行了验证,实验结果表明,经过载波相位平滑后的伪距噪声得到了降低,从而能够进一步提高GPS/SINS组合导航系统的定位精度,其位置误差均方根值相比无载波相位平滑减小近40%。     

Bounds on Elevation Error Estimates of a Target in Multipath

The Cramer-Rao bound for an unbiased estimate of the elevation angle of a target in the presence of multipath is calculated for the symmetric (target and image symmetric about the elevation symmetry plane of antenna) and nonsymmetric cases for an antenna consisting of 21 elements. These bounds are compared to the maximum likelihood estimates and it is found that the rms error of the maximum likelihood estimate (which has a bias) is below the Cramer-Rao bound for unbiased estimates.     

卫星伪距多路径时空建模研究

目前,多路径误差是制约GPS技术向更高精度发展的主要误差源.为了减小静态观测环境下的多路径误差,基于多路径误差周期重复性的特点,提出了一种自适应噪声分析结合经验模态分解的方法处理原始数据,采用多项式拟合构建了函数模型,并利用该函数模型对相邻天的观测数据进行处理.实验结果表明,利用所提方法对观测数据进行处理,可有效减小多...     

基于伪距信息的COMPASS-MEO导航卫星单星定轨分析

COMPASS-MEO导航卫星的伪距观测量包含星站距离、接收机钟差和卫星钟差以及各种噪声。本文首先分析了接收机钟差和卫星钟差在一定间隔内主要表现为线性变化的特性,可以考虑将接收机和卫星钟差作为测距的偏差和偏差变化率和轨道一起进行求解。其次,利用实测的MEO导航单星伪距数据,进行了数据预处理和定轨试验,分别对站间无时间同步信息和有时间同步信息两种情况进行定轨、残差分析和参数解算。使用重叠弧段、轨道预报和激光观测数据验证定轨结果的精度。结果表明,两种情况下的定轨结果无明显差别。该定轨方法可以运用于MEO导航单星精密轨道的计算。     

Analysis of airborne GPS multipath effects using high-fidelity EM models

Airborne GPS systems are being upgraded to provide sufficient positioning accuracy to support automatic landing operations in low visibility conditions. This is made possible by differential GPS (DGPS), in which the errors common to the airborne receiver and ground station are removed by knowledge of the latter's precise location. However, errors specific to the airborne system remain, of which the dominant components are receiver noise and multipath. To support the assessment of the integrity of the signal in space, these residual errors are incorporated in a statistically based error model, designated as the "standard model." The standard model is defined as the standard deviation of a Gaussian distribution that overbounds the residual pseudo-range (PR) error. It relates the standard deviation of the overbounding distribution to the elevation angle of the satellite relative to the local level coordinate system. The international community is currently developing improved standards to enable DGPS systems to support landings in the worst visibility conditions (i.e., CAT III). As a part of this development, the standard model for multipath is being re-evaluated and an improved model is sought. In order to better characterize the residual multipath errors, tools for accurate calculation of the airframe scattering effects are needed. Development of such tools is the subject of this paper. A new method for accurately computing pseudo-range error, based on the use of high-fidelity EM models, is described. This approach provides new insight into the mechanisms causing multipath error.     

基于CCFHTLS算法的异步电动机转子故障检测

定子电流经低通滤波器处理后产生高斯有色噪声,限制了异步电机转子故障检测算法的辨识精度。针对该问题,提出一种抑制高斯有色噪声的异步电机故障检测技术。首先对采集到的定子电流进行预处理,利用逆同步旋转变换剔除基波,避免了直接检测时基波对故障辨识精度的影响。然后利用互相关函数(CCF)处理技术对高斯有色噪声的抑制作用,提出基于CCFHTLS算法的电机转子故障诊断技术。针对异步电机转子断条和偏心故障的识别进行试验,结果表明CCFHTLS算法可以有效抑制高斯有色噪声,并保留故障有用信息,显著地提高了故障检测的分辨率。     

一种多径条件下的MLS接收机测角误差分析新方法

为了准确分析多径环境条件下微波着陆系统接收机测角误差,在深入分析微波着陆系统(MLS)测角原理的基础上,提出了一种基于扫描波束主瓣等效替代的误差分析方法。该方法通过把往返波束脉冲主瓣用高斯钟形替代,准确计算了接收的扫描脉冲-3dB门限前后沿误差,建立了多路径条件下统一实用的接收脉冲包络波峰位置偏移误差模型和锁住闸门测量误差模型。为验证模型准确性,以特定的多径环境条件为例,计算MLS接收机的测角误差,将计算结果与利用Mathias经典模型的计算结果进行对比,并通过计算机仿真进行验证。结果表明,采用主瓣替代方法能够较好地克服经典模型精确分析误差方面的使用不足和缺陷,且对多径条件下接收机测角精度的准确评定具有一定的实用价值。     

Aircraft flight parameter estimation using acoustic multipath delays

The signal emitted by an airborne acoustic source arrives at a stationary sensor located above a flat ground via a direct path and a ground-reflected path. The difference in the times of arrival of the direct path and ground-reflected path signal components, referred to as the multipath delay, provides an instantaneous estimate of the elevation angle of the source. A model is developed to predict the variation with time of the multipath delay for a jet aircraft or other broadband acoustic source in level flight with constant velocity over a hard ground. Based on this model, two methods are formulated to estimate the speed and altitude of the aircraft Both methods require the estimation of the multipath delay as a function of time. The methods differ only in the way the multipath delay is estimated; the first method uses the autocorrelation function, and the second uses the cepstrum, of the sensor output over a short time interval. The performances of both methods are evaluated and compared using real acoustic data. The second method provides the most precise aircraft speed and altitude estimates as compared with the first and two other existing methods.     

Multi-objective approach in GNSS code discriminator design

In spread spectrum ranging system receivers such as the Global Navigation Satellite System (GNSS) receivers, a discriminator is used in the code tracking loop to provide an error signal for the tracking of incoming signals. Typically, the discriminator manipulates several correlator outputs to form the correction signal. A multi-objective approach is adopted here to design the coefficients associated with a multi-correlator-based discriminator to lead to a better performance tradeoff in large tracking range, acceptable multipath-induced bias, high sensitivity, free of ambiguity, and small variance. It is shown that the multiple-objective problem can be tackled via a quadratic/linear programming method, rendering the optimal coefficient vector for the implementation of the discriminator. In addition, as the discriminator design is often subject to conflicting requirements, it is shown that the proposed design approach is capable of establishing bounds on achievable performance. Examples with respect to BPSK (binary phase-shift keying) NRZ (nonreturn-to-zero), and BOC (binary-offset carrier) signals are given to illustrate the design approach.     

A Hybrid Navigation Concept Using a Spinning Satellite?Borne Interferometer and Self?Contained Equipment

This paper analyzes a hybrid navigation concept that uses signals from a radio interferometer mounted on a spinning geostationary satellite, preliminary position estimates from self-contained equipment, and stored a priori information on the past performance of this equipment. The craft-borne processor, optimum in the maximum a posteriori (MAP) sense, is designed to estimate position coordinates using only the incoming radio signals, although improved estimates result if the other two items are available. An error analysis starts with the derivation of an estimation error covariance matrix, whose elements depend on additive receiver noise and the physical parameters of the system. A minimum 1? estimation error in position is obtained by trading off these parameters. The effects of other major error sources, such as tropospheric phase fluctuations, multipath, and craft altitude uncertainty, are added to the estimation error to give a total 1? position error on the order of 3.7 to 5.6 km.     

Performance of a Square Law Pseudonoise Ranging Time-of-Arrival Estimator

The performance of a square law time-of-arrival (TOA) estimator that has been proposed for use in ASTRO-DABS, part of a possible satellite-based fourth generation air traffic control system is considered. The transmitted message consists of a pulse amplitude modulated (PAM) ranging sequence that, due to transmitter characteristics, is corrupted by an unknown frequency offset. The optimum TOA estimator, for the case of no frequency uncertainty, is first presented, together with a lower bound on the variance of the estimate generated. This is followed by the consideration of a suboptimum TOA estimator for which a high signal-to-noise ratio (SNR) performance analysis is carried out; here, the effects of frequency uncertainty are included. Next, the zero-crossing properties of the derivative of the (suboptimum) estimation statistic are presented and the results used to derive an upper bound to the TOA estimate variance that is valid for all SNR values. This latter result is significant because it displays the system threshold effect and complements performance lower bounds that may be derived via other methods. In addition, the method presented here may be applied to other optimum and suboptimum systems where a discrete set of parameters is to be estimated.     

箭载GPS信号传播误差改正模型的选优

误差修正模型是影响箭载GPS定位精度的关键问题之一。针对几种常用的GPS信号传播误差改正模型,探讨了各模型伪距延迟修正量的计算方法,分析和比较了各模型之间的差异,给出了组合误差修正模型的选优标准。实测数据计算结果表明,选优后的误差修正模型可有效提高目标定位精度。     

Multipath-adaptive GPS/INS receiver

Multipath interference is one of the contributing sources of errors in precise global positioning system (GPS) position determination. This paper identifies key parameters of a multipath signal, focusing on estimating them accurately in order to mitigate multipath effects. Multiple model adaptive estimation (MMAE) techniques are applied to an inertial navigation system (INS)-coupled GPS receiver, based on a federated (distributed) Kalman filter design, to estimate the desired multipath parameters. The system configuration is one in which a GPS receiver and an INS are integrated together at the level of the in-phase and quadrature phase (I and Q) signals, rather than at the level of pseudo-range signals or navigation solutions. The system model of the MMAE is presented and the elemental Kalman filter design is examined. Different parameter search spaces are examined for accurate multipath parameter identification. The resulting GPS/INS receiver designs are validated through computer simulation of a user receiving signals from GPS satellites with multipath signal interference present The designed adaptive receiver provides pseudo-range estimates that are corrected for the effects of multipath interference, resulting in an integrated system that performs well with or without multipath interference present.     

多径效应对GPS载波相位观测量的影响

推导了ＧＰＳ接收机中多径效应引入的最大载波相位跟踪误差的闭合形式。得到以下结论：当直达信号跟踪误差不超过１码片时,最大载波测相多径误差为１／４周,该值出现在测码伪距多径误差最小的情况下;当直达信号跟踪误差超过或等于１码片时,接收机跟踪多径信号,信号误检发生。