一种高可靠长寿命的推进系统

介绍单元肼为推进剂的卫星推进系统，该系统已成功用于我国地球同步轨道通信卫星，高可靠，长寿命。叙述了系统及各部件的主要性能，关键部件的特性与可靠性试验，材料相容性试验，微粒控制及系统热试车。根据多年的飞行试验及地验对系统进行了可靠性计算。     

Reconfigurable multiport amplifiers for in-orbit use

A highly reliable and economical system design is presented for a multiport amplifier (MPA) system, which has attracted considerable attention for its potential use in multibeam mobile satellite communications. An MPA is composed of multiple input/output ports and an array of multiple high-power amplifier (HPAs). Since the HPAs are shared among multiple beams, this design solves the problems of traffic imbalance among beams, traffic changes due to terminal movement, and changes in propagation conditions, and can efficiently utilize the total transmitting power with maximum flexibility and minimum hardware. The problem is that HPA failures degrade the MPA beam isolation, causing multipath interference in the surrounding area due to leakage through adjacent beams. To address this problem, we investigated the MPA performance and survival probability when HPAs fail, by taking the specific properties of the MPA configuration into account. Based on our analysis, we found that there is an optimum operational HPA on/off mode in the event of HPA failure, and we were able to obtain optimal performance and reliability by reconfiguring the HPA on/off states in orbit upon the occurrence of HPA failures. Our proposed self-redundant, reconfigurable MPA can achieve high reliability without any need for additional redundant units or switches.     

Optimum Design of Single Channel per Carrier Satellite Systems

Optimization of available satellite power and transponder bandwidth is utilized to minimize the Earth station G/T in satellite channel per carrier (SCPC) systems. The corresponding optimum transponder output backoff is obtained. Applications in system design are given. In a previous paper [1] the channel capacity of a satellite transponder handling single channel per carrier (SCPC) transmission was derived. The link carrier-to-noise (C/N) ratio was maximized over the output backoff and the maximum bandwidth available was determined. Given the bandwidth per channel for each carrier, the channel capacity was obtained. The objective of the present investigation is to derive the minimum G/T of the Earth station in SCPC systems by optimum utilization of available satellite power and transponder bandwidth. Applications in system design are discussed.     

Spread-Spectrum Multiple Access Using Wideband Noncoherent MFSK

Two spread-spectrum multiple access systems which usewideband M-ary frequency shift keying (FSK) (MFSK) as theprimary modulation are presented. A bit error rate performanceanalysis is presented and system throughput is calculated for sample C band and Ku band satellite systems. Sample link analyses areincluded to illustrate power and adjacent satellite interferenceconsiderations in practical multiple access systems.     

A (design-oriented) reliability model for active phased arrays insatellite communication systems

This paper proposes a modeling approach to relate the power section reliability of satellite payloads to the on-board antenna complexity. The aim of the model is to support the development of design tools for satellite systems adopting active phased arrays. The achieved results are rendered parametric with respect to a key system requirement, the effective isotropic radiated power, due to its direct impact on transmitter configuration and technological features as well as on the critical compromise between transmitter and antenna specifications     

Project Trinidad

The first intercontinental satellite communication link, which involved the NASA Echo I balloon, a transmitting station on the Island of Trinidad, and a receiving station at Floyd, NY, is discussed. Rome Air Development Center (RADC) experimental stations were set up using a great deal of ingenuity and makeshift equipment and on a very small budget. Much of the equipment was salvaged from unrelated systems, while some was hand-built for this project. The implementation of the system, the testing of the system using moon bounce, the first orbital launch of the Echo I balloon, and the early difficulties encountered in the project are reviewed     

基于失效物理的动量轮贝叶斯可靠性评估

作为卫星姿态控制系统关键部件的动量轮,其可靠性关系到卫星发射的成败。但是由于有小子样、高可靠性和长寿命等特点,受技术、费用和时间等条件的限制,无法获得大样本失效寿命数据,因此利用传统的大样本寿命数据统计推断方法进行可靠性建模、分析与评估存在困难。为此,从失效物理分析的角度出发建立性能退化模型,用贝叶斯方法融合性能退化模型和寿命模型得到产品的可靠性评估模型,并基于该模型充分利用失效物理试验中的性能数据和少量的寿命数据来进行可靠性评估。实例分析表明,该方法与伪寿命方法相比更加符合工程实际,评估精度更高。     

TWT Reliability in Space

The question of Traveling Wave Tube (TWT) reliability in space poses some unique problems. First, since tube reliability has a tremendous impact on system design and overall cost, if problems do occur, they are highly visible. Second, attaining high reliability is made difficult by small production runs and short delivery schedules. Finally, the now-common 10 year life specification is combined with state-of-the-art performance requirements, forcing design changes and adding risk. To meet these requirements, we emphasize certain design and manufacturing ground rules. When orbital TWT problems do occur, our experience is that they are usually caused by infant mortality, not wearout. Data based on operation in space show that with close attention to the details of design and manufacturing, reliability exceeding the 500,000 hours MTBF normally specified is achieved. Traveling Wave Tube reliability and overall performance have a tremendous impact on system design and the overall cost of a satellite. TWT reliability determines the amount of redundancy needed to meet a given satellite mission objective. Increased redundancy means increased complexity and weight of the spacecraft. The TWTs, with their Electronic Power Conditioners, also dissipate over 80% of all spacecraft power. Increased tube efficiency will therefore simplify matters all around. Because of the critical impact of tubes, if technical problems do occur, they are highly visible at the system level, where rumors of failure spread like wildfire in the fairly small space community. Attaining high reliability is difficult because of the many conflicting requirements.     

宽波束赋形天线星地测试技术分析与改进

为满足风云三号 G星长寿命、高可靠、业务化的工作要求,星上数传天线采用通信性能好、覆盖率高的宽波束赋形设计。但宽波束赋形天线测试技术相对复杂,对测试质量有潜在影响。文章重点阐述了风云三号 G星数传天线设计方案的必要性,建立星地链路余量分析,对星载数传天线的仿真和试验结果比对进行分析,验证了天线方向图测试结果的有效性,并对星载天线和地面系统的测试技术提出改进,提高了测试结果的准确性和完整性。相应技术的改进可以为平台方案相近的空间辐射测量基准卫星平台系统综合试验验证技术提供支撑。     

30/20 GHz Band Small Earth Station for ISSDN Experiment

The system design and operational results of a 30/20 GHz band small Earth station for integrated services satellite digital network (ISSDN) experiments are presented. The Earth station has a high efficiency offset Cassegrain antenna with elliptical beam, a high power klystron amplifier with 1 kW output power and an uncooled parametric low noise amplifier with 200 K noise temperature. Experiments were performed using the medium capacity communications satellite for experimental purposes (CS). Performance on the Earth station was high. Effective radiation power (ERP) was greater than 88.1 dBW, and the receiving figure of merit (G/T) was larger than 30.6 dB/K. Good transmission characteristics were obtained through the satellite link for demand assigned time-division multiple access (DA-TDMA) with 20 Mbit/s bit rate.     

多滤波器并联方式解决直升机动力传动链扭振耦合

为了解决直升机动力传动链扭振系统与动力控制系统的耦合不稳定性问题,提出了一种采用多个陷波滤波器并联组合、根据发动机不同的工作模态选择不同滤波器实现扭振滤波的方法。对陷波滤波器进行了改进,使得引入控制系统通频带的附加相移减小,降低了对系统控制性能的影响。通过直升机联合试验,验证了该方法是有效的。      

无人机系统的卫星中继数据链

针对大中型无人机系统实现远程测控与信息传输的技术需求,在参考国外＂捕食者＂、＂全球鹰＂等先进无人机系统技术体制和实现方案的基础上,提出了利用商业或军用通信卫星作为空中中继平台,建立无人机卫星中继数据链,实现我国远程无人机系统的超视距遥控、遥测和侦察信息实时传输的解决方案,这对延伸无人机系统的作用距离、提高作战效能具有重要意义。文中分析了无人机系统卫星中继数据链的技术体制,提出了工程应用中的关键技术,对具体的工程实现具有一定的指导意义。     

整星隔振技术的研究现状和发展

为了减小卫星发射时所承受的环境载荷,降低卫星及其设备的质量控制成本,提高卫星发射的可靠性,所以整星隔振技术得以研究和应用。整星隔振是在不改变卫星原结构前提下,重新设计具有隔振效能的适配器,或者在运载火箭和卫星之间引入隔振装置,隔离从星箭界面传递给卫星的轴向或侧向振动。详细介绍了近十年国外整星隔振技术的研究现状,并展望其今后的发展方向。     

Ground-to-satellite laser communication experiments

Ground-to-satellite laser communication experiments between the optical ground station located in Koganei, central Tokyo, and a low earth orbit (LEO) satellite were jointly performed by the Japan Aerospace Exploration Agency and the National Institute of Information and Communications Technology. In 18 trials during three non-consecutive months, the satellite was acquired and tracked 61 % of the time, when clear or partly-clear conditions were predominant. The optical link was maintained for about 6 minutes when the satellite was visible in spite of the high angular velocity of the satellite. In 3 of the 18 trials, the link was not interrupted due to clouds during the six-minute transit. The failures (39% of the time) occurred when cloudy or rainy conditions were predominant. Fluctuation in the uplink received signal power was minimized by using multiple laser beam transmissions. The measured uplink and downlink bit error ratios were 10^-7-10^-4. These results demonstrate the applicability of free-space laser communication for not only geostationary earth orbit-LEO optical links but also ground-to-LEO optical links.     

一种提高UDP可靠性的数据传输方法研究

针对传统的UDP协议数据传输效率高但可靠性差的特点,提出了一种基于分区确认的分包与重组方法,使用自适应拥塞控制机制,并提出乘性增加减性减少（multiplicative increase reduced decrease,MIRD）算法对超时间隔进行处理,实现了音频数据的实时可靠传输,满足了特定场合下大量数据的传输实时性强和可靠性高的要求,提高了带宽利用的公平性和稳定性,拓展了UDP协议的使用范围。实验验证了该方法的可行性．音频数据传输的可靠性得到了提高。     

故障容错光交叉通道数据链路的可靠性

光交叉通道数据链路(OCCDL)是光传飞行控制系统余度计算机之间进行数据交换的重要途径.为了提高OCCDL系统的可靠性,提出一种新的具有多链路故障容错能力的OCCDL系统.给出了该OCCDL系统的结构配置,分析了系统正常工作和故障工作情况下的工作流程,设计了系统光开关故障、光链路等关键部分的故障容错逻辑,建立了基于马尔...     

低轨微纳卫星全磁自主导航算法研究

针对低轨微纳卫星体积小、功耗低的设计约束,提出了基于低轨地磁的定轨/定姿全磁自主导航算法.该算法仅利用三轴磁强计测量值和卫星动力学方程建立Kalman滤波器,实现了低轨微纳卫星的全自主轨道确定和姿态测量,理论仿真结果表明,该全磁导航算法精度能够满足低轨微纳卫星的一般要求.利用高精度地磁模拟器搭建了微纳卫星全磁自主导航地面仿真验证系统,对算法进行了全物理仿真测试和实验误差分析,进一步验证了全磁自主导航算法的可行性,为低轨微纳卫星提供了一种低成本、高自主、高可靠性的导航方法.     

某型发动机防喘/消喘控制系统分析研究

某型发动机研制过程中,防喘/消喘控制系统是其设计的薄弱环节及影响安全的关键之处。为解决这一问题,利用某型综合电子调节器及内外场专用设备对其防喘/消喘控制功能进行了详细的研究分析。研究表明:发动机防喘判据应根据发动机高压压气机转速和发动机进口压力进行动态修正,同时,应对系统采取一定保护措施,以提高系统工作的可靠性和安全性。      

COTS星载双模测控应答机基带设计与实现

提出了一种星载双模测控应答机基带设计方案,采用COTS（商用现货）器件实现,能较好解决星载功率受限和空间辐射效应引起的相关问题。测控应答机主处理器由反熔丝FPGA（现场可编程门阵列）实现,可在低功耗条件下保证最基本测控需求,解调上行DPSK（差分相移键控）信号,调制下行扩频信号;协处理器受主处理器控制,由SRAM（静态存储器）FPGA来实现,对上行扩频信号进行解扩解调。测控应答机可根据星载电源功率情况和不同测控任务切换模式,具有成本低、可靠性高、使用灵活等优势。     

过驱动轮控卫星的动态控制分配方法

反作用飞轮在卫星姿态控制中具有重要作用,配置3个以上飞轮的卫星构成一类过驱动系统,能够提高姿态控制系统的可靠性.针对期望控制力矩到冗余飞轮的指令分配问题,提出了一种基于伪逆法的动态控制分配方法,并针对传统伪逆法难以考虑飞轮最大力矩等物理约束问题,采用零空间方法对传统伪逆法给出的分配结果进行了修正.基于稳定控制模式下姿态...