鲁棒EKF在脉冲星导航系统中的应用

针对脉冲星导航系统的滤波问题,传统的扩展卡尔曼滤波(EKF)算法存在不能克服系统模型存在不确定性参数以及乘性噪声等缺陷,提出一种鲁棒EKF算法。首先,分析了状态预测误差方程和估计误差方程,利用统计学原理,得到了状态预测方差矩阵和状态估计方差矩阵计算等式。由于系统模型存在不确定性参数,状态预测协方差矩阵和状态估计协方差矩阵无法计算;因此,利用4个重要矩阵不等式,分析并找到预测方差矩阵和状态估计方差矩阵的上界。最后,利用状态估计误差协方差矩阵上界设计状态增益矩阵,使得状态估计协方差矩阵的迹最小。将该算法对脉冲星导航系统进行仿真,仿真结果验证了所提算法的有效性。     

自适应扩展增量 Kalman 滤波方法

基于扩展增量Kalman滤波方法(EIKF)和自适应增量Kalman滤波(AIKF),建立自适应扩展增量Kalman(AEIKF)模型及其分析方法,给出递推算法.在许多实际情况(如深空探测),由于环境因素的影响、测量设备的不稳定性等原因,量测方程往往存在未知的系统误差,并且模型参数也具有不确定性,结果导致较大的Kalman滤波误差,影响滤波的收敛性.提出的AEIKF方法能够成功消除这种未知的系统误差,并能够实时估计变化的噪声统计量,提高Kalman滤波精度.该方法计算简单,便于工程应用.      

自校准扩展Kalman滤波方法

提出一种自校准扩展Kalman滤波(SEKF)方法,针对3种含有未知输入(如未知系统误差、突风、故障等)的不同的非线性系统模型,分别给出了滤波递推算法.在导航、信号处理、故障诊断等领域的许多非线性工程中,传统的扩展Kalman滤波(EKF)方法无法消除未知输入的影响,在滤波过程中往往产生较大误差甚至发散.提出的SEKF方法能够对这种未知输入进行补偿和修正,从而提高滤波精度.数值仿真算例表明:SEKF的滤波误差均值和标准差分别减少到传统EKF的1/12和1/4,有效地改善了滤波精度.并且该方法计算简单,便于工程应用.      

Robust extended Kalman filter with input estimation for maneuver tracking

This study investigates the problem of tracking a satellite performing unknown continuous maneuvers. A new method is proposed for estimating both the state and maneuver acceleration of the satellite. The estimation of the maneuver acceleration is obtained by the combination of an unbiased minimum-variance input and state estimation method and a low-pass filter. Then a threshold-based maneuver detection approach is developed to determinate the start and end time of the unknown maneuvers. During the maneuvering period, the estimation error of the maneuver acceleration is modeled as the sum of a fluctuation error and a sudden change error. A robust extended Kalman filter is developed for dealing with the acceleration estimate error and providing state estimation. Simulation results show that, compared with the Unbiased Minimum-variance Input and State Estimation (UMISE) method, the proposed method has the same position estimation accuracy, and the velocity estimation error is reduced by about 5 times during the maneuver period. Besides, the acceleration detection and estimation accuracy of the proposed method is much higher than that of the UMISE method.     

紊流风场下的无人机飞行状态卡尔曼滤波估计

为了模拟紊流风场下的无人机飞行状态响应,减小紊流风场对无人机飞行速度的影响,使用数值法建立了紊流风场有色噪声模型,生成了符合大气紊流相关特性的紊流风场并对其进行数值仿真。在此基础上,通过状态扩增处理将系统噪声白化,设计出一种基于有色噪声的无人机飞行速度卡尔曼滤波器,该滤波器解决了基本卡尔曼滤波仅适用于白噪声的情况。仿真结果表明,使用此滤波器可有效减小紊流风场对无人机飞行速度的影响,进而满足飞行速度控制输入的精度要求。     

Simultaneous state and actuator fault estimation for satellite attitude control systems

In this paper, a new nonlinear augmented observer is proposed and applied to satellite attitude control systems. The observer can estimate system state and actuator fault simultaneously. It can enhance the performances of rapidly-varying faults estimation. Only original system matrices are adopted in the parameter design. The considered faults can be unbounded, and the proposed augmented observer can estimate a large class of faults. Systems without disturbances and the fault whose finite times derivatives are zero piecewise are initially considered, followed by a discussion of a general situation where the system is subject to disturbances and the finite times derivatives of the faults are not null but bounded. For the considered nonlinear system, convergence conditions of the observer are provided and the stability analysis is performed using Lyapunov direct method. Then a feasible algorithm is explored to compute the observer parameters using linear matrix inequalities (LMIs). Finally, the effectiveness of the proposed approach is illustrated by considering an example of a closed-loop satellite attitude control system. The simulation results show satisfactory perfor-mance in estimating states and actuator faults. It also shows that multiple faults can be estimated successfully.     

一种基于冗余测量的自适应卡尔曼滤波算法

针对目前自适应滤波算法的不足,在测量系统量测噪声方差未知的情况下,设计了一种基于冗余测量的自适应卡尔曼滤波(RMAKF)算法。通过对系统冗余测量值的一阶、二阶差分序列进行有效的统计分析,可以准确估计系统量测噪声统计特性,进而在滤波过程中自适应调节噪声方差阵R,提高滤波精度。以全球定位系统/惯性导航系统(GPS/INS)松组合导航系统为对象进行了仿真实验,结果表明该算法在测量系统噪声特性未知或发生改变时,可对其进行准确估计,在采用低精度惯性器件情况下,滤波结果较其他主要自适应卡尔曼滤波算法有较明显的改进。     

Quadratic extended Kalman filter approach for GPS/INS integration

GPS/INS integration system has been widely applied for navigation due to their complementary characteristics. And the tightly coupled integration approach has the advantage over the loosely coupled approach by using the raw GPS measurements, but hence introduces the nonlinearity into the measurement equation of the Kalman filter. So the typical method for navigation using measurements of range or pseudorange is by linearizing the measurements in an extended Kalman filter (EKF). However, the modeling errors of the EKF will cause the bias and divergence problems especially under the situation that the low quality inertial devices are included. To solve this problem, a quadratic EKF approach by adding the second-order derivative information to retain some nonlinearities is proposed in this paper. Simulation results indicate that the nonlinear terms included in the filtering process have the great influence on the performance of integration, especially in the case that the low quality INS is used in the integrated system. Furthermore, a two-stage cascaded estimation method is used, which circumvents the difficulty of solving nonlinear equations and greatly decreases the computational complexity of the proposed approach, so the quadratic EKF approach proposed in this paper is of great value in practice.     

基于Kalman滤波的变体飞行器T-S模糊控制

针对变体飞行器的跟踪控制问题,提出了一种基于Kalman滤波的T-S模糊控制方法。考虑飞行器系统状态不可测,引入惯导数据作为辅助信息,利用Kalman滤波算法融合飞控信息与惯导信息实现状态估计。由于变体飞行器在不同变形结构下气动特性变化较大,为便于控制器设计,采用小扰动线性化方法得到飞行器在不同平衡点处的局部线性模型,并通过状态反馈方法设计局部控制器,局部线性模型和局部控制器通过模糊集和模糊规则聚合成一个连续光滑的全局T-S模糊模型和T-S模糊控制器。通过综合Kalman滤波器与T-S模糊控制器得到一个基于Kalman滤波的T-S模糊控制器。仿真结果表明,该控制器在变形过程中能够实现状态估计,保证飞机的跟踪性能。     

近地航天器量子导航定位卡尔曼滤波算法研究

针对近地航天器量子导航定位系统,为了进一步提高其定位精度,利用滤波技术将QPS测量值结合航天器的运动模型进行状态量的滤波估计.给出了基于基线干涉原理的量子定位系统观测方程和以二体运动为主的航天器轨道运动模型,在此基础上详细推导了扩展卡尔曼滤波处理过程,并针对该模型进行了仿真.仿真结果表明,基于EKF的量子导航定位精度有明显提高.     

基于自适应容积卡尔曼滤波方法的涡扇发动机气路部件故障诊断

针对涡扇发动机气路部件故障诊断中参数存在不同的噪声统计特性,提出了一种自适应平方根容积卡尔曼滤波(ASRCKF)器的自适应滤波方法.该方法直接利用基于3阶容积积分方法近似发动机的非线性统计特性,用于替代非线性无迹卡尔曼滤波方法的系统模型,避免了滤波过程参数选取的问题;采用移动窗口法对噪声协方差矩阵进行自适应估计,提高了算法对不同统计特性噪声的自适应能力和滤波精度.通过对发动机气路部件健康参数蜕化过程仿真结果表明:ASRCKF方法相比平方根容积卡尔曼滤波(SRCKF)方法,精度提高40%~50%,对不同噪声信号具有更好的适应能力.      

基于Kalman滤波的空天飞行器再入制导算法

针对空天飞行器应用传统数值预测校正再入制导算法实时性不佳的问题,提出一种基于Kalman滤波的预测校正制导算法。该算法采取四阶多项式拟合速度-高度飞行剖面,利用Kalman滤波估计选定的速度点对应的高度,得到满足再入走廊及航程要求的拟合系数。在此基础上,减少一个终端约束,增加一个待估计剖面参数,可实现对再入过程飞行时间的调节。研究发现,再入过程中通过在线辨识修正不确定性参数能够提高制导指令的适应性;飞行末段利用跟踪参考剖面制导可有效避免飞行速度与终端速度接近时发生拟合系数求解发散的问题。多组不同再入条件下的算例仿真结果表明,基于Kalman滤波的空天飞行器再入制导算法实时性好,制导精度高,能够实现飞行时间可控,具有较强的鲁棒性和工程应用潜力。     

A novel strong tracking cubature Kalman filter and its application in maneuvering target tracking

The fading factor exerts a significant role in the strong tracking idea. However, traditional fading factor introduction method hinders the accuracy and robustness advantages of current strong-tracking-based nonlinear filtering algorithms such as Cubature Kalman Filter (CKF) since traditional fading factor introduction method only considers the first-order Taylor expansion. To this end, a new fading factor idea is suggested and introduced into the strong tracking CKF method. The new fading factor introduction method expanded the number of fading factors from one to two with reselected introduction positions. The relationship between the two fading factors as well as the general calculation method can be derived based on Taylor expansion. Obvious superiority of the newly suggested fading factor introduction method is demonstrated according to different nonlinearity of the measurement function. Equivalent calculation method can also be established while applied to CKF. Theoretical analysis shows that the strong tracking CKF can extract the third-order term information from the residual and thus realize second-order accuracy. After optimizing the strong tracking algorithm process, a Fast Strong Tracking CKF (FSTCKF) is finally established. Two simulation examples show that the novel FSTCKF improves the robustness of traditional CKF while minimizing the algorithm time complexity under various conditions.     

A practical filter error method for aerodynamic parameter estimation of aircraft in turbulence

It is common for aircraft to encounter atmospheric turbulence in flight tests. Turbulence is usually modeled as stochastic process noise in the flight dynamics equations. In this paper, parameter estimation of nonlinear dynamic system with both process and measurement noise was studied, and a practical filter error method was proposed. The linearized Kalman filter of first-order approximation was used for state estimation, in which the filter gain, along with the system parameters and the initial states, constituted the parameter vector to be estimated. The unknown parameters and measurement noise covariance were estimated alternately by a relaxation iteration method, and the sensitivities of observations to unknown parameters were calculated by finite difference approximation. Some practical aspects of the method application were discussed. The proposed filter error method was validated by the flight simulation data of a research aircraft. Then, the method was applied to the flight tests of a subscale aircraft, and the aerodynamic stability and control derivatives were estimated. All the estimation results were compared with the results of the output error method to demonstrate the effectiveness of the approach. It is shown that the filter error method is superior to the output error method for flight tests in atmospheric turbulence.     

Adaptive Gaussian sum squared-root cubature Kalman filter with split-merge scheme for state estimation

The paper deals with state estimation problem of nonlinear non-Gaussian discrete dynamic systems for improvement of accuracy and consistency. An efficient new algorithm called the adaptive Gaussian-sum square-root cubature Kalman filter（AGSSCKF） with a split-merge scheme is proposed. It is developed based on the squared-root extension of newly introduced cubature Kalman filter（SCKF） and is built within a Gaussian-sum framework. Based on the condition that the probability density functions of process noises and initial state are denoted by a Gaussian sum using optimization method, a bank of SCKF are used as the sub-filters to estimate state of system with the corresponding weights respectively, which is adaptively updated. The new algorithm consists of an adaptive splitting and merging procedure according to a proposed split-decision model based on the nonlinearity degree of measurement. The results of two simulation scenarios（one-dimensional state estimation and bearings-only tracking） show that the proposed filter demonstrates comparable performance to the particle filter with significantly reduced computational cost.     

Distributed state estimation for linear time-invariant dynamical systems: A review of theories and algorithms

Distributed state estimation is of paramount importance in many applications involving the large-scale complex systems over spatially deployed networked sensors. This paper provides an overview for analysis of distributed state estimation algorithms for linear time invariant systems. A number of previous works are reviewed and a clear classification of the main approaches in this field are presented, i.e., Kalman-filter-type methods and Luenberger-observer-type methods. The design and the stabil...     

Model-based robust estimation and fault detection for MEMS-INS/GPS integrated navigation systems

In micro-electro-mechanical system based inertial navigation system（MEMS-INS）/global position system（GPS） integrated navigation systems, there exist unknown disturbances and abnormal measurements. In order to obtain high estimation accuracy and enhance detection sensitivity to faults in measurements, this paper deals with the problem of model-based robust estimation（RE） and fault detection（FD）. A filter gain matrix and a post-filter are designed to obtain a RE and FD algorithm with current measurements, which is different from most of the existing priori filters using measurements in one-step delay. With the designed filter gain matrix, the H-infinity norm of the transfer function from noise inputs to estimation error outputs is limited within a certain range; with the designed post-filter, the residual signal is robust to disturbances but sensitive to faults. Therefore, the algorithm can guarantee small estimation errors in the presence of disturbances and have high sensitivity to faults. The proposed method is evaluated in an integrated navigation system, and the simulation results show that it is more effective in position estimation and fault signal detection than priori RE and FD algorithms.     

A combined technique of Kalman filter,artificial neural network and fuzzy logic for gas turbines and signal fault isolation

The target of this paper is the performance-based diagnostics of a gas turbine for the automated early detection of components malfunctions. The paper proposes a new combination of multiple methodologies for the performance-based diagnostics of single and multiple failures on a two-spool engine. The aim of this technique is to combine the strength of each methodology and provide a high success rate for single and multiple failures with the presence of measurement malfunctions. A combination of KF (Kalman Filter), ANN (Artificial Neural Network) and FL (Fuzzy Logic) is used in this research in order to improve the success rate, to increase the flexibility and the number of failures detected and to combine the strength of multiple methods to have a more robust solution. The Kalman filter has in his strength the measurement noise treatment, the artificial neural network the simulation and prediction of reference and deteriorated performance profile and the fuzzy logic the categorization flexibility, which is used to quantify and classify the failures. In the area of GT (Gas Turbine) diagnostics, the multiple failures in combination with measurement issues and the utilization of multiple methods for a 2-spool industrial gas turbine engine has not been investigated extensively.This paper reports the key contribution of each component of the methodology and brief the results in the quantification and classification success rate. The methodology is tested for constant deterioration and increasing noise and for random deterioration. For the random deterioration and nominal noise of 0.4%, in particular, the quantification success rate is above 92.0%, while the classification success rate is above 95.1%. Moreover, the speed of the data processing (1.7 s/sample) proves the suitability of this methodology for online diagnostics.     

一种星敏感器-陀螺组合定姿的实时在轨标定方法

研究了一种星敏感器一陀螺组合定姿方式中的姿态敏感器误差的实时在轨标定方法。首先,选择直观的欧拉角作为姿态描述参数,根据星敏感器和陀螺的测量原理建立星敏感器一陀螺在轨标定的测量方程和状态方程,并以此建立数学模型。其次,采用简单高效的EKF（ExtendedKalmanFilter,扩展卡尔曼滤波）作为估值算法,进行了在轨标定数值仿真。对于航天器姿态定向中出现的姿态角和星敏感器安装角之间的耦合问题,通过在特定姿态通道上施加简单姿态机动实现了解耦。数值结果表明,该实时在轨标定方法,尤其是所提出的姿态角和星敏感器安装角解耦策略,可以实现对航天器姿态的实时精确估计以及对星敏感器安装误差、陀螺常值漂移和相关漂移等误差的实时在轨标定。该方法可用于航天器姿态测量设备的实时在轨标定和航天器姿态的高精度实时确定。     

A novel fault tolerant permanent magnet synchronous motor with improved optimal torque control for aerospace application

Improving fault tolerant performance of permanent magnet synchronous motor has always been the central issue of the electrically supplied actuator for aerospace application. In this paper, a novel fault tolerant permanent magnet synchronous motor is proposed, which is characterized by two stators and two rotors on the same shaft with a circumferential displacement of mechanical angle of 4.5. It helps to reduce the cogging torque. Each segment of the stator and the rotor can be considered as an 8-pole/10-slot five-phase permanent magnet synchronous motor with concentrated, single-layer and alternate teeth wound winding, which enhance the fault isolation capacity of the motor. Furthermore, the motor has high phase inductance to restrain the short-circuit current. In addition, an improved optimal torque control strategy is proposed to make the motor work well under the open-circuit fault and short-circuit fault conditions. Simulation and experiment results show that the proposed fault tolerant motor system has excellent fault tolerant capacity, which is able to operate continuously under the third open-circuit fault and second shortcircuit fault condition without system performance degradation, which was not available earlier.