翼型前缘变形对动态失速效应影响的数值计算

翼型或机翼的动态失速效应所引起的低头力矩和正气动阻尼限制了飞行器气动性能的提高,甚至可能诱导发生不稳定运动。应用于小尺寸机翼的前缘动态变形（DDLE）技术,通过实时改变前缘形状,能够改善翼型前缘区域的速度梯度,进而抑制动态失速效应。采用转捩剪切应力输运（SST）黏性模型结合分区混合动态网格技术,研究了这种前缘变形对机翼俯仰运动所引起的非定常流动的影响,得到通过小幅度前缘变形抑制和延迟动态失速的方法,从而提高翼型的气动性能。翼型NAC A0012的数值模拟结果与动态失速风洞试验结果比较表明：所使用的数值计算方法能够较为准确地模拟翼型在动态失速过程中升力系数与俯仰力矩系数的变化情况,可用于研究前缘变形对翼型俯仰运动所引起的非定常流动的影响。前缘动态变形翼型俯仰运动过程的非定常流场的数值模拟表明：在大迎角下不同幅度的前缘下垂运动能够抑制流动分离的发生,从而抑制动态失速,但在大迎角下小幅度高频率的前缘下垂变形能更高效地抑制动态失速;前缘变形幅度以及变形沿中弧线的分布对升力系数和俯仰力矩系数的影响并不明显。     

前缘下垂结合内吹式襟翼失速特性研究

内吹式襟翼具有高效的增升能力,但失速迎角在较高的吹气动量系数下下降明显,为改善其失速特性,研究内吹式襟翼加装前缘下垂后的失速特性。对前缘下垂结合无缝襟翼的亚声速翼型在环量控制作用下的流场进行数值模拟,研究吹气动量系数对失速特性的影响规律,前缘刚性偏转、弯度变化和厚度变化对失速特性的改善作用,以及改变襟翼偏角研究前缘下垂的作用效果。结果表明：随着吹气动量系数的增加,失速迎角先迅速下降再略微增加;前缘下垂装置减小了翼型上表面逆压梯度,延缓了翼型边界层动量厚度随迎角增加而增加的趋势,能有效提高失速迎角;通过逐渐改变前缘表面曲率,实现了前缘下垂设计对失速特性改善的最好效果。     

Experimental and numerical investigation of threedimensional vortex structures of a pitching airfoil at a transitional Reynolds number

This research examines the vortex behaviors and aerodynamic forces in dynamic stall phenomena at a transitional Reynolds number(Re = 90000) using experimental and numerical approaches.Periodic sinusoidal pitching motion at two different reduced frequencies is used to achieve the dynamic stall of a NACA 0012 airfoil.Several leading edge vortices form and detach in the dynamic stall stage.The flow then quickly transitions to a full separation zone in the stall stage when the angle of attack starts to decrease.There is discrepancy between the phaseaveraged and instantaneous flow field in that the small flow structures increased with angle of attack, which is a characteristic of the flow field at the transitional Reynolds number.The interaction between the streamwise vortices in the three-dimensional numerical results and the leading edge vortex are the main contribution to the turbulent flow.In addition, the leading edge vortex that supplies vortex lift is more stable at higher reduced frequency, which decreases the lift fluctuation in the dynamic stall stage.The leading edge vortex at higher reduced frequency is strong enough to stabilize the flow, even when the airfoil is in the down-stroke phase.     

变来流速度下旋翼翼型非定常气动特性分析

为分析变来流速度状态下的旋翼翼型气动特性,提出了利用翼型平移来模拟来流速度变化的数值方法.在此方法基础上,采用基于隐式LU-SGS(lower upper symmetric Gauss-Seidal)方法的非定常雷诺平均N-S(Navier-Stokes)(RANS)方程,模拟了SC1095旋翼翼型在定迎角 变来流速度及变迎角 变来流速度状态下的非定常气动特性.通过对比分析发现:翼型在变速度-定迎角状态下会表现出明显的非定常现象,产生了前缘分离涡,气动特性会出现明显的迟滞效应及波动现象,脉动速度越大,非定常效果越明显.并且基准速度越大,翼型气动特性的峰值越大;翼型迎角越大,非定常涡出现的也越早.考虑直升机旋翼翼型实际工作环境,在变速度-动态失速状态下,翼型最大迎角处的气动力会得到一定程度的削弱,在小迎角下的气动力得到一定程度的增强,且脉动速度越大,翼型的非定常特性也越强.      

翼型动态失速等离子体流动控制试验

针对动态失速引起的翼型气动性能恶化的问题,利用小型化的激励电源和介质阻挡放电等离子体激励器,借助动态压力测量和外触发式粒子图像测速（PIV）等手段开展了翼型动态失速等离子体流动控制试验研究。结果表明,等离子体气动激励能够有效控制翼型动态失速,改善平均气动力,提高翼型气动效率,减小气动力随迎角变化的迟滞区域。等离子体诱导出前缘附近的贴体翼面涡,促进分离流再附;增加了上翼面0.2~0.4弦长区域的吸力,减小了升力系数功率谱密度（PSD）分布的二、三、四阶能量幅值,在研究工况下实现了平均升力系数增加7.1%、失速迎角推迟1.3°和迟滞区域减小4.5%的明显控制效果;4°~9°迎角段,等离子体使得翼型平均阻力系数减小40%。此外,振荡频率增加使翼型绕流的非定常性增强,较高雷诺数下的翼型动态分离涡更加难以被抑制,均需要增加等离子体激励强度才能达到较好的控制效果。     

应用协同射流原理的旋翼翼型增升减阻试验研究

协同射流技术作为一种新型主动流动控制技术,是突破旋翼翼型高增升减阻设计的最有潜力的发展方向之一。以 OA312 旋翼翼型作为基准翼型,研制微型涵道风扇组为驱动的旋翼翼型 CFJ 风洞测力模型,开展基于前缘高负压零质量内循环协同射流原理的旋翼翼型高增升减阻低速风洞试验,研究吹气口大小、吸气口大小和上翼面下沉量等基础参数对增升减阻的影响规律,探讨 CFJ 旋翼翼型关键参数最佳取值。结果表明：与OA312 基准翼型相比,小攻角状态时,CFJ 旋翼翼型可显著降低阻力系数,甚至出现“负阻力”现象,实现了零升俯仰力矩基本不变;大攻角状态时,CFJ 旋翼翼型可显著提升最大升力系数和失速迎角,其中,最大升力系数可提升约 67.5%,失速迎角推迟了近 14.8°。     

Dynamic stall suppression on an oscillating airfoil by steady and unsteady tangential blowing

The use of steady and unsteady tangential blowing to suppress the dynamic stall on an oscillating airfoil was studied by numerically solving the Reynolds averaged Navier-Stokes equations. Pitching oscillations with amplitude of 10° about a mean angle of attack of 15° and with reduced frequencies of 0.15 and 0.25 were examined. The blowing location is near the airfoil leading edge, and for unsteady blowing, the jet strength was varied periodically at the same frequency as that of airfoil oscillation with some phase difference. In case of steady blowing, with a C_μ of 0.07, the large pitching moment, massive drop in C_L and increase in C_D due to dynamic stall were eliminated. The unsteady blowing was found more effective than the steady blowing.     

Aerodynamic shape optimization for alleviating dynamic stall characteristics of helicopter rotor airfoil

In order to alleviate the dynamic stall effects in helicopter rotor, the sequential quadratic programming(SQP) method is employed to optimize the characteristics of airfoil under dynamic stall conditions based on the SC1095 airfoil. The geometry of airfoil is parameterized by the class-shape-transformation(CST) method, and the C-topology body-fitted mesh is then automatically generated around the airfoil by solving the Poisson equations. Based on the grid generation technology, the unsteady Reynolds-averaged Navier-Stokes(RANS) equations are chosen as the governing equations for predicting airfoil flow field and the highly-efficient implicit scheme of lower–upper symmetric Gauss–Seidel(LU-SGS) is adopted for temporal discretization. To capture the dynamic stall phenomenon of the rotor more accurately, the Spalart–Allmaras turbulence model is employed to close the RANS equations. The optimized airfoil with a larger leading edge radius and camber is obtained. The leading edge vortex and trailing edge separation of the optimized airfoil under unsteady conditions are obviously weakened, and the dynamic stall characteristics of optimized airfoil at different Mach numbers, reduced frequencies and angles of attack are also obviously improved compared with the baseline SC1095 airfoil. It is demonstrated that the optimized method is effective and the optimized airfoil is suitable as the helicopter rotor airfoil.     

仿生正弦前缘对翼面动态失速的影响

动态失速导致叶片气动载荷急剧变化，造成振动载荷激增，桨叶寿命大幅衰减。针对动态失速问题，从座头鲸胸鳍在动态倾转下取得良好的流动特性获得启示，据此模化出仿生正弦前缘翼面（包含3种波峰和2种波长），旨在实现动态失速控制。借助三维非定常数值模拟方法，采用运动网格技术，基于SC1095旋翼翼型，研究了仿生前缘动态失速流动控制机理及运动参数和来流速度的影响。结果表明：正弦前缘大幅度降低俯仰力矩系数峰值和阻力系数峰值；前缘波峰越大、波长越小，阻力系数峰值与俯仰力矩系数峰值的抑制效果越明显，虽然升力系数峰值减小，但其减小量远小于前两者，例如其中一种仿生翼使俯仰力矩系数峰值减小了47.7%，阻力系数峰值减小了36.4%，升力系数峰值减小14.1%；在最大迎角附近，正弦前缘能够缓和失速特性，使载荷变化更为平缓；在高平均迎角、低俯仰频率、低马赫数下，仿生翼动态失速控制效果更强，相比较而言迎角振幅的影响较小。     

基于充气前缘技术的旋翼翼型动态失速抑制

动态失速的发生会在直升机旋翼桨叶和桨毂上产生高的交变扭转振动载荷,并限制直升机高速重载状态下的使用包线。本文利用计算流体力学(CFD)方法对基于充气前缘(ILE)技术的SC1095旋翼翼型动态失速抑制进行研究,分析了ILE抑制动态失速的控制机理,获得了ILE结构布置和充放气方式对动态失速的影响规律。研究表明:ILE可以有效抑制动态失速的发生;ILE最大膨胀程度越大,其抑制动态失速的效果越好,但膨胀程度过大后抑制效果开始减弱;ILE在翼型上仰至最大迎角时恰好达到最大膨胀状态,其对动态失速的抑制效果最好;ILE保持最大膨胀状态的时间长短对抑制效果影响不大;在翼型上仰至不同迎角时开始对ILE充气会对动态失速抑制有较大影响;ILE整流段与翼型连接位置对动态失速抑制有很大影响,整流段越长,抑制效果越好。     

带有气动及结构非线性的二元机翼颤振分析

研究了翼型在低马赫数条件下的非定常气动特性,从翼型表面气流运动的角度对Leishman-Beddoes(L-B)模型进行了修正,并在此基础上建立了适合低马赫数颤振研究且带有气动及结构非线性的二元机翼气弹系统分析模型.对比低马赫数翼型气动载荷试验结果表明对L-B模型的修正是有效的,且机翼颤振试验结果亦验证了二元机翼气弹分析模型.研究结果表明:二元机翼气弹系统的失速颤振与初始变距角和来流速度密切相关,且耦合的三次非线性变距和浮沉刚度是造成系统呈现准周期运动的主要原因.      

Wake structure and similar behavior of wake profiles downstream of a plunging airfoil

Very limited attention has already been paid to the velocity behavior in the wake region in unsteady aerodynamic problems.A series of tests has been performed on a flapping airfoil in a subsonic wind tunnel to study the wake structure for different sets of mean angle of attack,plunging amplitude and reduced frequency.In this study,the velocity profiles in the wake for various oscillation parameters have been measured using a wide shoulder rake,especially designed for the present experiments.The airfoil under consideration was a critical section of a 660 kW wind turbine.The results show that for a flapping airfoil the wake structure can be of drag producing type,thrust producing or neutral,depending on the mean angle of attack,oscillation amplitude and reduced frequency.In a thrust producing wake,a high-momentum high-velocity jet flow is formed in the core region of the wake instead of the conventional low-momentum flow.As a result,the drag force normally experienced by the body due to the momentum deficit would be replaced by a thrust force.According to the results,the momentum loss in the wake decreases as the reduced frequency increases.The thrust producing wake pattern for the flapping airfoil has been observed for suffi ciently low angles of attack in the absence of the viscous effects.This phenomenon has also been observed for either high oscillation amplitudes or high reduced frequencies.According to the results,for different reduced frequencies and plunging amplitudes,such that the product of them be a constant,the velocity profiles exhibit similar behavior and coalesce on each other.This simi larity parameter works excellently at small angles of attack.However,at near stall boundaries,the similarity is not as evident as before.     

扇翼飞行器翼型附面层控制数值模拟

基于扇翼飞行器翼型特殊的几何形状及流场特性,在原有翼型的弧形槽下方和后缘加装控制阀门,通过调节阀门开启及开启尺寸的大小,利用弧形槽低压涡所产生的吸力对翼型后缘的附面层进行一定的控制,达到增升减阻的效果。通过采用计算流体力学的方法对其机理及阀门开启尺寸的影响进行了详细计算和分析,研究表明当阀门开启的尺寸为10 mm时,修改翼型的最大升力系数、失速迎角及相同迎角下的升力系数和推力系数均大于基本翼型;随着阀门开启尺寸的增大,修改翼型的最大升力系数和失速迎角均减小,但是在失速前,修改翼型在相同迎角下的升力系数大于基本翼型。此方法可以改变先前通过增大横流风扇的转速来提高其气动性能的做法,减小了能量的消耗,增大了整个飞行器的航程,为扇翼飞行器能够早日投入实际运用奠定了一定的理论基础。     

介质阻挡放电等离子体对NACA0015翼型流动控制的PIV实验研究

采用粒子图像测速（Particle Image Velocimetry,PIV）技术,研究了介质阻挡放电等离子体激励对NA-CA0015翼型表面流动分离的控制特性。通过风洞实验,研究了电极电压、电极位置和布置方式等参数对翼型分离控制的影响规律,并初步分析了等离子体流动控制机理。结果表明等离子体激励在失速迎角附近可以有效抑制翼型的流动分离,实现气流的完全再附着;在来流速度为20m/s时,将气流再附着的迎角提高了5°。     

Individual influence of pitching and plunging motions on flow structures over an airfoil during dynamic stall

The individual influence of pitching and plunging motions on flow structures is studied experimentally by changing the phase lag between the geometrical angle of attack and the plunging angle of attack. Five phase lags are chosen as the experimental parameters, while the Strouhal number, the reduced frequency and the Reynolds number are fixed. During the motion of the airfoil, the leading edge vortex, the reattached vortex and the secondary vortex are observed in the flow field. The leading edge vortex is found to be the main flow structure through the proper orthogonal decomposition. The increase of phase lag results in the increase of the leading edge velocity, which strongly influences the leading edge shear layer and the leading edge vortex. The plunging motion contributes to the development of the leading edge shear layer, while the pitching motion is the key reason for instability of the leading edge shear layer. It is also found that a certain increase of phase lag, around 34.15° in this research, can increase the airfoil lift.     

等离子体气动激励抑制机翼失速分离的实验

进行了等离子体气动激励抑制机翼失速分离的风洞实验,研究了等离子体气动激励频率、电压、占空比和激励位置等对流动控制效果的影响.研究表明:在来流速度35m/s时,等离子体气动激励可以有效地抑制机翼大攻角下吸力面的流动分离,将机翼临界失速迎角由17°提高到19°;施加激励后,机翼最大升力系数提高了9.45%,阻力系数减小20.9%;激励频率在200Hz时,控制效果最好,对应的量纲一激励频率为1;迎角越大,流动分离越严重,需要更大的激励电压才能够有效抑制流动分离;最佳激励位置在流动分离起始点的前缘;在流动控制效果相当时,减小占空比可以降低能耗.      

Experimental study of ice accretion effects on aerodynamic performance of an NACA 23012 airfoil

In this paper,the effects of icing on an NACA 23012 airfoil have been studied.Experiments were applied on the clean airfoil,runback ice,horn ice,and spanwise ridge ice at a Reynolds number of 0.6 106 over angles of attack from 8° to 20°,and then results are compared.Generally,it is found that ice accretion on the airfoil can contribute to formation of a flow separation bubble on the upper surface downstream from the leading edge.In addition,it is made clear that spanwise ridge ice provides the greatest negative effect on the aerodynamic performance of the airfoil.In this case,the stall angle drops about 10° and the maximum lift coefficient reduces about50% which is hazardous for an airplane.While horn ice leads to a stall angle drop of about 4° and a maximum lift coefficient reduction to 21%,runback ice has the least effect on the flow pattern around the airfoil and the aerodynamic coefficients so as the stall angle decreases 2° and the maximum lift reduces about 8%.     

直升机动态失速研究

本文简要介绍了旋翼和翼型的动态失速特性、动态失速主动和被动控制、旋翼综合法预测使用的一些动态失速模拟方法.UH-60A直升机飞行试验11029飞行是一个典型的旋翼动态失速实例,表演出旋翼后行桨叶上出现高攻角引起的动态失速,而前行桨叶上则出现因为激波诱导前缘分离引起的动态失速.翼型的动态失速特性方面介绍了典型的动态失速迟滞回线(攻角正弦变化和锯齿变化)、缩减频率和雷诺数对翼型动态失速特性的影响等.动态失速主动控制介绍可动前缘翼型的情况,被动控制则是使用前缘涡发生器的情况.     

OA212翼型主动流动控制的数值模拟研究

采用数值模拟的方法,探讨了基于零质量射流的主动流动控制技术对OA212旋翼翼型动态失速的控制效果和控制特性.以积分形式雷诺平均Navier-Stokes(N-S)方程为控制方程,采用格心有限体积法进行求解.空间离散采用AUSM~+-up格式,时间推进采用含牛顿型LU-SGS子迭代的全隐式双时间法,且引入了预处理方法和多重网格方法加速收敛.通过在喷口上施加非定常边界条件来模拟射流对翼型绕流的影响.研究了不同类型射流、不同位置射流以及不同控制参数(频率、相位、偏角、动量系数等)对动态失速控制效果的影响.研究表明:零质量射流和传统的定常射流均可减小动态失速迟滞环的回线面积,但在提高最大升力方面零质量射流明显优于定常射流;在12%c和62%c处施加组合零质量射流的控制效果最为明显.     

翼伞弧面下反角、翼型和前缘切口对翼伞气动性能的影响

为了研究翼伞弧面下反角、翼型和前缘切口对翼伞气动性能的影响,对带气室的、展弦比为3的不同特征几何参数翼伞模型的流场进行了三维、定常数值模拟。运用有限体积法对三维坐标系下不可压雷诺时均Navier-Stokes (RANS)方程进行了直接求解,采用剪切应力输运(SST)k-ω两方程湍流模型对湍流进行模拟。数值模拟得出的原始翼伞的气动性能参数与试验数据在总趋势上符合很好,不同几何参数翼伞模型计算结果表明:翼伞弧面下反角越大,升力及诱导阻力越小,升阻比变化不大;前缘半径、厚度小的翼伞翼型,阻力更小,升阻比大;前缘切口对翼伞影响区域限于前缘附近,压力分布同干净翼类似,降低了其失速迎角,对升力影响不大,但明显增大阻力。该数值方法可为进一步研究更多不同几何参数的翼伞模型提供参考。