共查询到20条相似文献,搜索用时 62 毫秒
1.
大型客机涡扇发动机动力特性模拟 总被引:1,自引:0,他引:1
机体/发动机干扰问题是现代大型客机设计中必须考虑和解决的核心问题之一。长期以来,商用和in-house计算流体力学(CFD)软件,都是通过在发动机进气口设置质量流量比,排气口和外涵道设置总温比/总压比,建立动力特性模型来等效模拟机体/发动机干扰流场。在现有动力特性模型基础上,借鉴特征边界思想,将外涵道指定为特征边界,建立了一种新的发动机动力特性模型。采用轴对称超高涵道比涡扇发动机模型、轴对称涡轮动力模型以及某型客机带发动机模型对两种动力特性模型进行了系统的验证和确认,结果表明:两种发动机动力特性模型均能很好地模拟涡扇发动机动力效应,且计算结果与试验数据吻合较好,说明了两种动力特性模型的正确性、可靠性以及工程适用性。此外,所建立的新动力特性模型特别适合于大涵道比涡扇发动机的动力效应模拟,且可以在外涵道总温比、总压比等参数未知的情形下,评估发动机的动力特性,在实际工程中应用更广泛。 相似文献
2.
3.
借助涡扇发动机风车特性研究的最新成果,开展了某型涡扇发动机的风车性能数值模拟研究.首先,基于不可压流理论,附以可压缩效应修正的指数法发展了补充慢车转速以下部件特性的计算模型和计算程序;其次,根据流量连续、压力平衡、功率平衡、燃烧室进出口总温相等及转速相等等约束条件建立了风车状态时涡扇发动机高低压转子及整机的共同工作方程;最后发展了具有一定计算精度的涡扇发动机风车状态特性计算模型和程序,并以某型涡扇发动机为例,计算分析了不同飞行条件下发动机的风车特性,从计算结果看,其趋势是合理的. 相似文献
4.
多用途战斗机/涡扇发动机一体化循环参数优化 总被引:6,自引:0,他引:6
针对多用途战斗机的特点,发展了基于飞/发一体化的涡扇发动机循环参数优化设计模型和相应的计算程序,优化设计模型中包括双变量控制涡扇发动机特性计算模型、进排气系统安装特性计算模型、飞机气动特性分析模型、重量组成分析模型、任务剖面分析模型、约束分析与任务分析模型和优化计算模型等。重点研究了多用途战斗机约束边界的获得方法,利用多岛遗传算法和自适应模拟退火优化算法,分别对现役多用途战斗机、不加力超声速巡航多用途战斗机以及下一代先进多用途战斗机用涡扇发动机循环参数进行了优化计算,对计算结果进行了分析,获得了对多用途战斗机用涡扇发动机循环参数选择有指导意义的结论。 相似文献
5.
为了探索一种便于进行涡扇发动机过渡态控制规律设计的性能计算模型,提出了基于部件法的涡扇发动机加减速的显式格式和隐式格式计算方法,该方法通过在发动机计算模型中直接给定喘振裕度限制值、燃烧室油气比限制值和涡轮进口总温的限制值,计算出最优的加减速特性,进而获得发动机的最优加减速控制规律。计算模型针对不同的给定值,选择了不同的燃烧室容积效应模型。证明了对一般的涡扇发动机,隐式格式计算模型中,给定压气机喘振裕度算法的解是唯一的。以某涡扇发动机在地面的加减速过程为例,按最优加减速控制规律计算,显式格式算法和隐式格式算法的结果误差小于1.3%.对给定高压转子转速加速率的加速特性也进行了验算,计算结果与最优加速过程的结果误差小于1.7%.本文提出的加减速特性计算方法可为涡扇发动机的过渡态开环和闭环控制规律设计提供便捷的手段。 相似文献
6.
7.
某型涡扇发动机起动过程数值模拟 总被引:5,自引:3,他引:2
基于发动机设计点参数和压气机、涡轮高转速特性数据,完善了一种计算风扇、高压压气机和高、低压涡轮小转速特性近似方法,并进一步基于涡扇发动机部件匹配技术,建立了某型涡扇发动机起动过程计算模型及相应算法,给出了比较合理的发动机起动过程模拟结果. 相似文献
8.
考虑雷诺数、湿度等影响因素的涡扇发动机小偏差模型 总被引:2,自引:2,他引:0
建立了一个考虑雷诺数、湿度等影响因素的涡扇发动机小偏差模型。通过分析 ,得到了雷诺数、湿度对涡扇发动机特性的影响系数及影响系数矩阵。以涡扇发动机为例进行计算 ,结果表明 :该模型可以定量、定性的分析各个影响因素对涡扇发动机特性的影响 相似文献
9.
加力式SteamJet发动机性能模拟 总被引:1,自引:0,他引:1
为了研究射流预冷却涡轮发动机(SteamJet)的发动机特性,建立了喷水预冷却的热交换系统计算、物性修正计算和发动机部件特性修正计算的数学模型,建立了基于双轴混排加力式涡扇发动机的Steam-Jet发动机性能计算模型,并编制了相应的计算程序.计算分析了SteamJet发动机在不同风扇进口总温下沿飞行轨道的特性,以及喷水预冷却对发动机加力燃烧室的影响,并对SteamJet发动机风扇进口总温进行了合理的选择;对加力式SteamJet发动机进行了高度速度特性的计算和分析.结果表明,SteamJet发动机可大幅度拓宽涡轮发动机的工作范围,与非加力式SteamJet发动机相比,加力式SteamJet发动机具有更好的推力特性,能够满足高超声速飞行的需求. 相似文献
10.
11.
有翼高超声速再入飞行器气动设计难点问题 总被引:2,自引:1,他引:2
有翼高超声速再入飞行器是近年来的研究热点,气动设计是飞行器设计的关键。为了更清楚地认识有翼高超声速再入飞行器气动设计的难点问题,对有翼高超声速再入飞行器的发展、优势及总体任务剖面进行了介绍,从5个方面详细介绍了该类飞行器气动设计的难点问题,包括多约束复杂面对称气动布局设计、高温真实气体效应对气动特性影响、天地差异与天地换算方法、反作用控制系统(RCS)喷流干扰对气动特性的影响以及气动数据不确定度等,简要阐明了这些难点问题对总体设计的重要性以及初步的解决思路,为有翼高超声速再入飞行器气动设计提供了一些参考。 相似文献
12.
LUO Cheng LIU Hua YANG Jia-ling LIU Kai-xin 《中国航空学报》2007,20(3):230-235
Crashworthiness requirement of fuel tanks is one of the important requirements in helicopter designs. The relations among the protection frame, textile layer and rubber layer of the fuel tank are introduced. Two appropriate FE models are established, one is for an uncovered helicopter fuel tank without protection frame, and the other is for fuel tank with protection frame. The dynamic responses of the two types of fuel tanks impinging on the ground with velocities of 17.3 m/s are numerically simulated for the purpose of analyzing energy-absorbing capabilities of the textile layer and protection frame. The feasibility of the current crashworthiness design of the fuel tank is examined though comparing the dynamic response behaviors of the two fuel tanks. 相似文献
13.
波音公司面临着来自空客公司的巨大挑战,企业战略性创新才是公司成功的关键。为此波音公司的全部战略性研究集中在扩大产品的差异性上,体现在3个方面:电子化(e-Enabled)运营环境、整体复合材料机身部件的制造技术和支持波音787客机的全球协同环境(GCE)。 相似文献
14.
The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow 总被引:1,自引:0,他引:1
This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation. 相似文献
15.
临近空间飞行器测控与信息传输系统频段选择 总被引:7,自引:0,他引:7
临近空间飞行器是高性能信息化武器平台,测控(TT&;C)与信息传输系统是其信息保障的核心,而选择合理、可行的频段是展开系统设计的前提和基础。频段选择影响到整个技术方案的制定,是一个需综合考虑、影响深远并具有战略意义的关键问题,从国际电联(ITU)国际标准、高速数传、接收信噪比(SNR)、“三抗”、超视距中继、黑障、雨衰以及设备研制成熟度8个方面全面、细致论证了近空间平台测控系统的频段选择问题,最终得出在视距链路中以Ka频段为宜,在超视距链路中以Ku/Ka双频段为宜的结论。 相似文献
16.
基于弯曲激波压缩系统的高超声速进气道反设计研究进展 总被引:3,自引:0,他引:3
总结了近十年来弯曲激波压缩研究的主要成果。提出了弯曲激波压缩系统的新概念,即利用特殊设计的楔形弯曲压缩面或空间弯曲压缩面,产生一系列与前缘弱激波相互交汇或叠加的压缩波系,从而使前缘激波弯曲,形成特殊的弯曲激波,它与波后的等熵压缩波来共同完成对气流的压缩。在此基础上,实现了由给定出口气动参数的超声速内流道反设计,实现了由给定压缩面压力分布和给定压缩面马赫数分布要求的型面反设计,实现了由给定激波波面的压缩型面反设计。研究证明,弯曲压缩面-弯曲激波压缩系统具有良好的综合气动性能,为高性能高超声速进气系统的气动设计提供了一种全新的设计方法。 相似文献
17.
Wu Xianyu Li Xiaoshan Ding Meng Liu Weidong Wang Zhenguo 《中国航空学报》2007,20(6):488-494
In order to investigate the effects of fuel injection distribution on the scramjet combustor performance, there are conducted three sets of test on a hydrocarbon fueled direct-connect scramjet test facility. The results of Test A, whose fuel injection is carried out with injectors located on the top-wall and the bottom-wall, show that the fuel injection with an appropriate close-front and centralized distribution would be of much help to optimize combustor performances. The results of Test B, whose fuel injection is performed at the optimal injection locations found in Test A, with a given equivalence ratio and different injection proportions for each injector, show that this injection mode is of little benefit to improve combustor performances. The results of Test C with a circumferential fuel injection distribution displaies the possibility of ameliorating combustor performance. By analyzing the effects of injection location parameters on combustor performances on the base of the data of Test C, it is clear that the injector location has strong coupled influences on combus- tor performances. In addition, an inner-force synthesis specific impulse is used to reduce the errors caused by the disturbance of fuel supply and working state of air heater while assessing combustor performances. 相似文献
18.
(高)超声速流动试验技术及研究进展 总被引:1,自引:1,他引:1
近年来,与高速飞行器相关的(高)超声速流动受到了极大的关注。这类流动所具有的非定常性、强梯度和可压缩性对试验方法和风洞设计技术提出了挑战。超声速纳米示踪平面激光散射(NPLS)技术是由作者所在团队研发的非接触光学测试技术。它能够以较高的空间分辨率来揭示超声速三维流场的一个瞬态剖面的时间解析的流动结构。介绍了NPLS技术以及基于NPLS开发的密度场测量、雷诺应力测量和气动光学波前测量等方法,并回顾了这些技术在超声速边界层、超声速混合层、超声速压缩拐角、激波/边界层相互作用和光学头罩绕流等流动中的应用,清晰地再现了边界层、混合层、激波等典型流场结构及其时空演化特性。另外,为了模拟和研究高空大气条件下边界层自然转捩和超声速混合层的转捩特性,介绍了高超声速静风洞、超-超混合层风洞的设计技术以及层流化喷管的设计方法。 相似文献
19.
Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis 总被引:2,自引:0,他引:2
GAO Hong-liang ZHANG Hui WANG Shu-juan 《中国航空学报》2007,20(1):75-80
Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved. 相似文献