共查询到17条相似文献,搜索用时 234 毫秒
1.
2.
3.
加速度计是惯性导航系统的核心部件,通常加速度计的输出信号为模拟电流,为便于导航计算机对采集数据解算处理,需经过I/F(电流/频率)转换电路。为满足某惯导系统对大比例系数加速度信号采集转换的要求,在经典I/F电路的基础上结合FPGA+A/D设计了一种比例系数大于90000脉冲/(s·mA),量程为6mA的电流频率转换电路,同时转换电路支持串口输出。通过对该大比例系数I/F转换电路的温度特性、线性度、零位稳定性等指标的测试,表明该电路性能良好,有利于进一步拓展应用范围。 相似文献
4.
R/D和S/D转换电路在雷达系统中将天线的角度和转动速度变换成数字量,由数据处理机采集,计算天线的伺服控制参数,并作为测角、测距计算的输入参数.首先介绍了同步器/解析器的基本概念,然后给出了一种采用RD14531芯片实现的R/D和S/D转换电路,详细讨论了芯片的特性,电路实现和测试方法. 相似文献
5.
介绍了一种0~1000 mV直流毫伏标准源的设计原理和技术方案,该方案采用20位D/A转换器作为基准,通过设计分压比分别为1000∶1,100∶1和10∶1的精密比例分压电路,实现了0~1000 mV直流标准电压信号的输出。 相似文献
6.
7.
8.
9.
机载电子设备的数字化是当前先进科学技术的发展方向。为了适应新技术的发展需要,作为高度传感器的雷达高度表的数字化势在必行。本文介绍的雷达高度表输出信号的数字化电路,以单片机系统为核心,使用8位 A/D 转换芯片,辅以适当的软件程序,输出高精度的12位二进制高度信息,显示高精度的5位十进制高度数据.该电路具有体积小、重量轻、功能全、精度高、适用性广的特点。 相似文献
10.
仪器由AT89C55单片机进行控制,通过键盘、LCD显示模块进行人机对话,完成波形选择、频段选择,频率、幅度输出控制。由MAX038产生正弦波、方波、三角波,其波形选择由单片机进行控制;频段选择由五档组成,可通过旋扭开关完成;频率由单片机输出数据经D/A转换后控制MAX038;幅度由单片机输出数据经D/A转换后改变放大器负反馈深度来实现输出信号幅度的变化。 相似文献
11.
一、引言 ADC1210是美国National Semiconductor公司生产的一种低功耗、中速、低价格的12位二进制码(原码、或反码、或偏置码)逐次逼近式A/D转换器。该器件采用CMOS工艺和薄膜工艺相结合的微电子技术制成。器件中包含了R-2R梯形薄膜电阻网络、CMOS模拟开关和逐次逼近逻辑电路、以及场效应管电压比较器等有关电路。其基本技术指标为分辨 相似文献
12.
It is difficult to obtain a large input/output voltage ratio with a DC-DC converter, because the duty factor d may not reach very small values. For the same reason, it is difficult to obtain an output voltage that is adjustable in a large range. A DC-DC converter circuit is proposed that overcomes this limitation by performing a voltage ratio d 2/(1-d ) in the best operating mode. Circuit operation is analyzed, operating modes are evidenced, and the voltage ratio is deduced in each operating mode as a function of output current, duty factor, and circuit component values. Boundary conditions between different operating modes are obtained; consequently, it is concluded that these conditions do not occur for some operating modes. Component ratings are summarized, to facilitate circuit design. The buck-flyback DC-DC converter is very suitable for low-voltage (e.g. computer) power supplies and for power supplies with the output voltage (adjustable in a large range) supplied from the mains without a mains voltage transformer 相似文献
13.
Huai Wei Batarseh I. Kornetzky P. 《IEEE transactions on aerospace and electronic systems》1999,35(4):1344-1353
A new single-stage single-switch power factor correction converter with output electrical isolation is presented. The configuration of this converter is achieved by combining a flyback circuit and a forward circuit in one power stage. The principle of operation and steady-state analysis of the proposed topology is given. Based on its steady-state operation constraints, a design procedure along with a specific design example is reported. To verify the theoretical analysis of the proposed converter, a design example is given with its PSPICE simulation and experimental results 相似文献
14.
The expression of the flyback converter output voltage (output power) is derived as a function of the supply voltage, load resistance, transformer ratios, transistor current gain, and base-circuit resistor value. Switching period and duty cycle are also calculated. A converter circuit is designed having stabilized output voltage, with respect to supply voltage, at constant load. The transistor base current is controlled by the supply voltage, via a nonlinear circuit. This feedforward circuit approximates with logarithmic characteristics the ideal hyperbolic dependence of the transistor base current as a function of the supply voltage. The converter has high performance and low cost. A cheaper circuit variant is presented, in which the high-voltage control transistor was eliminated. 相似文献
15.
分析与设计基于一种实用的三相高频斩波式AC/AC变换器的研制,以高频脉宽调制(PWM)技术取代了传统的基频电压补偿技术,不仅减小了体积和重量,且提高了效率和响应速度。主要对控制电路进行了分析与设计,其中包括输出采样电路、闭环反馈电路以及驱动电路;并对控制电路的稳定性进行了分析,给出了系统框图、传递函数以及波特图。在分析与设计中,通过稳定RMS值实现输出电压的稳定;采用有源滤波技术,减小了控制电路中的高次谐波干扰;利用齐纳二极管正温度特性,减小了系统的温度漂移,较好地补偿了采样电路中整流二极管的负温度特性;采用可编程调节死区的驱动电路,完全满足三相斩波式AC/AC变换器四路驱动信号的电器隔离和时序要求。 相似文献
16.
介绍了一种利用最新研发的电子元件和电流检测技术设计的DC 100A直流电流标准装置.该标准采用"ZERO-FLUK"技术解决了电流采样单元的零温漂、零功耗问题;采用高分辨力数模转换控制电路解决了系统控制精度和稳定性的问题. 相似文献
17.
单片机内嵌式A/D的使用要比外置式A/D简单、方便,且容易获得更高的信噪比,但其分辨力相对比较低,难以满足精密测量的使用要求。本文介绍了一种提高单片机内嵌式A/D转换器分辨力有效实用法,简单外转电路和单片机内部软件计算可以将原分辨力将提高1 ̄3倍。 相似文献