电磁霍普金森压杆电磁力控制参数分析

本文对电磁加载系统放电回路原理进行分析,研究了系统控制参数对电磁力应力波的影响规律。结果表明:减小放电回路电阻可保证设备在最大电容量和极限放电电压时放大器输出的应力波幅值足够大;增大放电回路线圈匝数,电磁力应力波的幅值升高,同时脉冲宽度变宽,选择电磁加载设备线圈匝数时应综合考虑应力波幅值和脉宽;放电回路电容量主要影响电磁力脉冲宽度,对电磁力幅值影响较小;电容充电电压主要影响电磁力幅值的大小,在放电回路其他参数一定时,可以通过改变电容充电电压来实现电磁加载设备输出应力波幅值的调整。     

电脉冲除冰系统的加速度试验研究

介绍了电脉冲除冰系统的加速度试验,并以峰值加速度为脉冲效果的评判标准,研究了该系统的脉冲性能参数如储能电容器的初始放电电压、电容器的电容量、脉冲线圈与试验蒙皮之间的间距、脉冲线圈的外径以及绕制线圈导线的厚度对脉冲效果的影响。结果表明,放电电压越大,电容量越大,脉冲线圈一试验蒙皮的间距越小,导线厚度越大均会使得峰值加速度...     

单级感应线圈炮出口速度仿真

在单级感应线圈炮的发射过程中,放电电压、电容容量以及电枢初始位置不同,弹丸的出口速度都会随之发生变化。文给出了单级感应线圈炮的数学模型,并以弹丸出口速度为目标函数,分别仿真分析了放电电压、电容容量以及电枢初始位置对弹丸出口速度的影响,得出了放电电压、电容容量以及电枢初始位置与弹丸出口速度的关系曲线。     

水工质脉冲等离子体推进器的能量平衡和效率

通过一种同轴水工质脉冲等离子体推进器的LCR放电回路的理论分析和实验来探讨其在运行过程中的能量平衡和能量转换效率。理论分析认为储能电容中的储存能量通过放电转化为加速动能及被传输线和电容的等效电阻消耗掉,并且根据等效电阻的分配情况定义了水工质脉冲等离子体推进器的加速动能和电磁力转换效率。实验研究表明:该水工质脉冲等离子体推进器的存储能量(E0=4.86J)转换成加速动能的能量转换效率是28%,其中11%用于电磁加速及17%用于电热加速,其余72%的存储能量消耗在储能电容和传输线内阻所造成的能量损失上。     

脉冲等离子体推力器火花塞的性能实验

点火回路引燃脉冲等离子体推力器的主电容放电,是推力器的关键部分之一,其性能直接影响到推力器运行的成败。实验设计了脉冲等离子体推力器的点火电路和同轴型、钩型、平行电极型三种结构的火花塞。在此基础上,获得了三种火花塞的充电电压、放电电流及点火情况。结果显示,平行电极型的点火效果最佳。最后分析了三种火花塞的点火机理,获得了较好放电性能的火花塞结构形式,为脉冲等离子体推力器的稳定运行提供了重要的依据。     

高速电磁阀响应特性的研究

为实现电磁阀的高速响应的要求,提出了自行设计基于电容放电的驱动电路,通过仿真研究,确定驱动电路参数的取值范围。对电磁阀线圈结构参数对响应特性的影响进行了仿真与试验研究,仿真和试验结果的比较表明设计电磁阀具有较好的动态响应特性。     

脉冲等离子体推力器烧蚀建模与仿真

为了深入地揭示平板型脉冲等离子体推力器（PPT）工作机理,通过对PPT在放电过程中的欧姆加热能量分配分析,建立了基于能量守恒原理的改进烧蚀模型,并对磁流体动力学方程中的能量方程进行了修正。结合LES-6对PPT工作过程进行了一维磁流体动力学数值仿真,获得了PPT的速度分布、放电烧蚀质量和元冲量等参数的变化过程。仿真结果表明,改进模型能正确地反映脉冲等离子体推力器工作过程,仿真得到的出口速度、元冲量与实验值吻合较好,而放电烧蚀质量则相对误差较大;当电容容量变化时,元冲量随放电能量增大呈近似的线性增长关系,放电烧蚀质量随放电能量的增大单调增加且呈非线性关系。     

适用于航天领域的高效叠加式升压变换器

叠加式升压变换器（SBC）的部分功率不通过开关电路,而通过叠加支路直接供给负载,因此可实现较高的效率,适用于航天场合。为了避免输入输出电流断续,采用的变压器为双边磁化的隔离脉冲单元,它与电感、输出滤波电容以及叠加支路共同组成SBC变换器。根据电感位置的不同,分别提出了SBC-Ⅰ、SBC-Ⅱ和SBC-Ⅲ的基本结构与生成规则。基于生成规则推衍出9种SBC变换器,并从电流特性、输入输出电压关系、主电路传递函数、变压器的磁偏问题以及效率的角度对这9种变换器进行分析比较。最后选择一种性能最优的变换器,通过600 W的实验样机验证理论分析结果。     

脉冲等离子体推力器放电波形设计评估仿真研究

运用磁流体动力学的方法,对脉冲等离子体推力器推力室工作过程开展三维双温MHD数值仿真,并开展对推力室的工作机理的分析研究。通过该模型计算得到的推进剂烧蚀质量和元冲量与实验结果相符,同时针对不同初始电压、电容以及两种特征波形的情况进行评估,为推力器的放电波形设计提供指导依据。结果显示在推力器波形设计的初期,是采用电流高变化率低能量水平,还是采用电流低变化率高能量水平,需要结合实际,进行优化评估。     

脉冲周期介质阻挡放电作用的PIV实验研究

静止大气下,对施加脉冲周期介质阻挡放电,半顶角为10°的圆锥前体进行了PIV实验研究。采用总平均和相位锁定平均方法对脉冲周期放电进行了分析;对比了不同占空比和不同相位角沿θ=90°半径上的切向速度和轴向涡量分布,得到了在圆锥表面等离子体诱导的最大速度和最大涡量;分析了脉冲周期放电的动量转移特性。实验结果表明：脉冲周期放电引发动量转移的主要机制是涡的增强而非气流的加速;当激励器处于脉冲放电间歇时,相位锁定平均的最大速度和最大涡量不为零,存在流动滞后效应,有利于节省能耗。     

The effect of inlet conditions on the flow and heat transfer in multiple rotating cavity with axial throughflow

This paper discusses experimental results from two different build configurations of a heated multiple rotating cavity test rig.Measurements of heat transfer from the discs and tangential velocities are presented.The test rig is a 70% full scale version of a high pressure compressor stack of an axial gas turbine engine.Of particular interest are the internal cylindrical cavities formed by adjacent discs and the interaction of these with a central axial throughflow of cooling air.Tests were carried out for a range of non-dimensional parameters representative of high pressure compressor internal air system flows(Re up to 5×106 and Rez up to 2×105).Two different builds have been tested.The most significant difference between these two build configurations is the size of the annular gap between the(non-rotating) drive shaft and the bores of the discs.The heat transfer data were obtained from thermocouple measurements of surface temperature and a conduction solution method.The velocity measurements were made using a two component,LDA system.The heat transfer results from the discs show differences between the two builds.This is attributed to the wider annular gap allowing more of the throughflow to penetrate into the cavity.There are also significant differences between the radial distributions of tangential velocity in the two builds of the test rig.For the narrow annular gap,there is an increase of non-dimensional tangential velocity V/Ωr with radial location to solid body rotation V/Ωr=1.For the wider annular gap,the non-dimensional velocities show a decrease with radial location to solid body rotation.      

Research on Auto-detection for Remainder Particles of Aerospace Relay Based on Wavelet Analysis

Aerospace relay is one kind of electronic components which is used widely in national defense system and aerospace system. The existence of remainder particles induces the reliability declining, which has become a severe problem in the development of aerospace relay. Traditional particle impact noise detection (PIND) method for remainder detection is ineffective for small particles, due to its low precision and involvement of subjective factors. An auto-detection method for PIND output signals is proposed in this paper, which is based on direct wavelet de-noising (DWD), cross-correlation analysis (CCA) and homo-filtering (HF), the method enhances the affectiv-ity of PIND test about the small particles. In the end, some practical PIND output signals are analysed, and the validity of this new method is proved.     

Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.     

Effects of Mo on the Microstructure and Hydrogen Sorption Properties of Ti-Mo Getters

The effects of Mo on the microstructure evolution, porosity and hydrogen sorption properties of Ti-Mo getters are investigated in this work. The results show that the addition of Mo prolongs the densification process of Ti-Mo getters and results in a significant amount of sintered pores. With the Mo content increasing, the porosity of getters firstly increases reaching the maximum value as it at- tains about 7.5wt.%, and then drops. At the room temperature, the hydrogen sorption property of getters increases progressively with the Mo content increasing, but the tendency is not very clear before its content lies below 2.5wt.%. When the Mo content achieves about 7.5wt.%, the hydrogen sorption property proves to be the best. The discussion is made about the above mentioned phenomena inclusive of hydrogen sorption properties of getters under different activation conditions (from 500-750 ℃).     

超声速燃烧数值模拟中的湍流与化学反应相互作用模型

高精度数值模拟有助于理解超声速湍流燃烧中湍流与化学反应的相互作用,可为发动机燃烧室等工程应用设计提供可靠的预测模型。除直接数值模拟外,目前在湍流燃烧应用中使用的大涡模拟和雷诺平均Navier-Stokes模拟均需要借助模型模化发生在湍流小尺度上的流动与化学反应过程对湍流大尺度运动的影响。现有的湍流与化学反应相互作用模型大致可分为:火焰面类模型和概率密度函数类模型,2类模型在不同的应用中各自具有优势和局限性。此外,现有模型大都基于低马赫数燃烧,而超声速燃烧中通常会伴随快速混合、局部熄火和再着火以及激波等复杂过程,这为发展其中的湍流与化学反应相互作用模型提出了更多的挑战。     

适于低轨卫星IP网络的单核共享树组播算法(英文)

为了解决低轨卫星IP网络中现有典型源组播算法的信道资源浪费问题,本文提出了一套单核共享树组播算法,即核心群合并共享树(CCST)和加权核心群合并共享树(w-CCST)算法。CCST 算法包括动态近似中心(DAC)选核方法和核心群合并组播路径构建方法。DAC方法专为周期、规律运动的低轨卫星网络提出,不需要复杂的星上计算。在核心群合并方法中,以核节点作为初始核心群,通过核心群和剩余组成员的最短路径方法逐步扩展直至整棵组播树构建完成,从而使得组播树的树代价最小,大大提高了网络的带宽利用率和组播传输效率。w-CCST 算法中所提出的加权因子可以调整树代价和端到端传播时延之间的折衷程度,因此,可以通过调整加权因子来适度增大树代价、降低端到端传播时延以支持某些端到端时延要求苛刻的实时组播业务。最后,与低轨卫星 IP 网络中典型算法进行了性能比较,仿真结果说明,CCST 算法的平均树代价比其它算法显著降低,w-CCST 算法的平均端到端传播时延小于 CCST 算法。     

Jet Vectoring Control Using a Novel Synthetic Jet Actuator

A primary air jet vectoring control system with a novel synthetic jet actuator (SJA) is presented and simulated numerically. The results show that, in comparison with an existing traditional synthetic jet actuator, which is able to perform the duty of either “push” or “pull”, one novel synthetic jet actuator can fulfill both “push” and “pull” functions to vector the primary jet by shifting a slide block inside it. Therefore, because the new actuator possesses greater efficiency, it has potentiality to replace the existing one in various appli- cations, such as thrust vectoring and the reduction of thermal signature. Moreover, as the novel actuator can fulfill those functions that the existing one can not, it may well be expected to popularize it into more flow control systems.     

Nonlinear Adaptive Slewing Motion Control of Spacecraft Truss Driven by Synchronous V-gimbaled CMG Precession

The slewing motion control of a truss arm driven by a V-gimbaled control-moment-gyro (CMG) is a nonlinear control problem. The V-gimbaled CMG consists of a pair of gyros that must precess synchronously. The moment of inertia of the system, the angular momentum of the gyros and the external disturbances are not exactly known. With the help of feedback linearization and recursive Lyapunov design method, an adaptive nonlinear controller is designed to deal with the unknown items. Performance of the proposed controller is verified by simulation.     

An SOR Implicit Time-accurate Scheme in Calculating Unsteady Flows

A new time-accurate marching scheme for unsteady flow calculations is proposed in the present work. This method is the combination of classical Successive Over-Relaxation (SOR) iteration method and Jacobian matrix diagonally dominant splitting method of LUSGS. One advantage of this algorithm is the second-order accuracy because of no factorization error. Another advantage is the low computational cost because the Jacobian matrices and fluxes are only calculated once in each physical time step. And, the SOR algorithm has better convergence property than Gauss-Seidel. To investigate its accuracy and convergency, several unsteady flow computa- tional tests are carried out by using the proposed SOR algorithm. Roe’s FDS scheme is used to discritize the inviscid flux terms. Un- steady computational results of SOR are compared with the experiment results and those of Gauss-Seidel. Results reveal that the numerical results agree well with the experimental data and the second-order accuracy can be obtained as the Gauss-Seidel for unsteady flow computations. The impact of SOR factor is investigated for unsteady computations by using different SOR factors in this algorithm to simulate each computational test. Different numbers of inner iterations are needed to converge to the same criterion for different SOR factors and optimal choice of SOR factor can improve the computational efficiency greatly.