首页 | 本学科首页   官方微博 | 高级检索  
     检索      

面齿轮滚刀基本蜗杆的设计方法
引用本文:王延忠,吴灿辉,葛旭阳,张俐.面齿轮滚刀基本蜗杆的设计方法[J].北京航空航天大学学报,2009,35(2):166-169.
作者姓名:王延忠  吴灿辉  葛旭阳  张俐
作者单位:北京航空航天大学机械工程及自动化学院,北京,100191;北京航空航天大学机械工程及自动化学院,北京,100191;北京航空航天大学机械工程及自动化学院,北京,100191;北京航空航天大学机械工程及自动化学院,北京,100191
基金项目:国家自然科学基金资助项目(50875009);;航空科学基金资助项目(20070451005);;博士点基金资助项目(20070006009);;装备预先研究项目(51318020206)
摘    要:面齿轮传动由于其独特的传动优点,成为航空传动的主要研究方向.根据面齿轮传动原理,建立面齿轮加工坐标系,得到了面齿轮齿面方程,分析了面齿轮齿顶变尖和齿根根切的限制条件,同时根据实际算例讨论了面齿轮内外半径随压力角变化的规律,所获得的结论对面齿轮的设计具有参考价值.最后分析面齿轮的滚切原理,根据齿轮啮合原理,建立面齿轮滚刀型面方程,采用数值计算方法,得到滚刀型面离散三维坐标值,借助三维造型软件得到面齿轮滚刀基本蜗杆三维模型.

关 键 词:面齿轮  齿面方程  齿根根切  齿顶变尖  滚刀  蜗杆
收稿时间:2008-07-20

Basal worm-designing method of face-gear hob
Wang Yanzhong,Wu Canhui,Ge Xuyangn,Zhang Li.Basal worm-designing method of face-gear hob[J].Journal of Beijing University of Aeronautics and Astronautics,2009,35(2):166-169.
Authors:Wang Yanzhong  Wu Canhui  Ge Xuyangn  Zhang Li
Institution:School of Mechanical Engineering and Automation, Beijing University of Aeronautics and Astronautics, Beijing 100191, China
Abstract:Face-gear drives become the main direction of research for aeronautical drives because of their special advantages.The applied coordinate systems of face-gear were set up and the equation of face-gear tooth surface was established,then the face-gear tooth surface constrain conditions for dedendum undercutting and addendum pointing were analyzed based on the face-gear transmission theory,at the same time,the disciplines were discussed on the relationships between pressure angle and the face-gear outer & inne...
Keywords:face-gear  equation of tooth surface  dedendum undercutting  addendum pointing  hob  worm  
本文献已被 CNKI 万方数据 等数据库收录!
点击此处可从《北京航空航天大学学报》浏览原始摘要信息
点击此处可从《北京航空航天大学学报》下载免费的PDF全文
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号