| 高压脉冲电子束的控制及其对焊缝形貌影响 |
| |
| 引用本文： | 许海鹰,余伟,左从进.高压脉冲电子束的控制及其对焊缝形貌影响[J].北京航空航天大学学报,2011,37(8):1044-1048. |
| |
| 作者姓名： | 许海鹰 余伟 左从进 |
| |
| 作者单位： | 北京航空制造工程研究所高能束流加工技术重点实验室,北京,100024;北京航空制造工程研究所高能束流加工技术重点实验室,北京,100024;北京航空制造工程研究所高能束流加工技术重点实验室,北京,100024 |
| |
| 摘 要： | 研制出一台150 kV/30 kW高压脉冲电子束焊机,介绍了控制脉冲束流产生的偏压脉冲电源拓扑电路结构及脉冲束流频率、占空比、束流基值、束流峰值的调节控制技术.在0~1 kHz频率范围内,该电源可输出最大幅值200 mA的脉冲电子束束流,且工艺参数调节方便.分别采用脉冲束流与连续束流电子束工艺焊接了1Cr18Ni9Ti奥氏体不锈钢,对不同工艺的焊缝形貌进行了对比分析.与连续束流电子束焊接工艺相比,采用脉冲电子束焊接工艺的焊缝熔深增加,深宽比增大;对于脉冲电子束焊接工艺,占空比给定时,随着束流频率增加,焊接缺陷减少.试验结果表明:脉冲束流频率、占空比是影响焊缝成形的关键工艺参数;脉冲调制方式控制偏压是获得高压脉冲电子束的理想控制技术之一.
|
| 关 键 词： | 高压 脉冲电子束 偏压脉冲 焊缝形貌 |
| 收稿时间： | 2010-03-23 |
High voltage pulse electron beam control strategy and influence on weld bead shape |
| |
| Xu Haiying Yu Wei Zuo Congjin.High voltage pulse electron beam control strategy and influence on weld bead shape[J].Journal of Beijing University of Aeronautics and Astronautics,2011,37(8):1044-1048. |
| |
| Authors: | Xu Haiying Yu Wei Zuo Congjin |
| |
| Institution: | Science and Technology on Power Beam Processes Laboratory, Beijing Aeronautical Manufacturing Research Institute, Beijing 100024, China |
| |
| Abstract: | A 150 kV/30 kW high voltage pulse electron beam welding power source was developed.The bias pulse power source topology and control technique about base beam current,peak beam current,pulse beam duty,pulse beam frequency were introduced.Not only the biggest peak beam current up to 200 mA has been exported by this power source at 0-1 kHz,but also weld technology parameters are expediently adjusted.The 1Cr18Ni9Ti stainless steel work pieces had been welded by electron beam welding and pulse electron beam weld... |
| |
| Keywords: | high voltage pulse electric beam bias pulse weld bead shapes |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
| 点击此处可从《北京航空航天大学学报》浏览原始摘要信息 |
| 点击此处可从《北京航空航天大学学报》下载免费的PDF全文 |
|
