首页 | 本学科首页   官方微博 | 高级检索  
     检索      

自循环机匣处理轴向位置影响扩稳能力的机理
引用本文:张皓光,安康,谭锋,楚武利,吴艳辉.自循环机匣处理轴向位置影响扩稳能力的机理[J].航空动力学报,2017,32(4):983-989.
作者姓名:张皓光  安康  谭锋  楚武利  吴艳辉
作者单位:1.西北工业大学 动力与能源学院,西安 710072
基金项目:国家自然科学基金(51006084);航空科学基金(2014ZB53014);中央高校基本科研业务费专项资金(3102014JCY01004);陕西省自然科学基金(2015JM5202)
摘    要:为了揭示自循环机匣处理轴向位置影响压气机稳定性的流动机理,采用非定常数值方法研究了3种不同轴向位置对机匣处理(CT)扩稳能力的影响,结果表明:机匣处理喷气装置离叶顶前缘最近且在叶顶前缘上游的扩稳能力最强,喷气装置在叶顶前缘正上方的次之,喷气装置在叶顶前缘上游较远处的最弱,对应机匣处理获得的综合失速裕度改进量分别为9.40%,7.09%,5.49%.通过详细地分析压气机叶顶流场表明:喷气装置离叶顶前缘最近且在叶顶前缘上游的机匣处理施加有利影响程度最高的范围刚好覆盖叶顶前缘处,此处是引起转子失速的关键部位,因此抑制叶顶间隙泄漏流造成的堵塞的效果最好,对应的扩稳能力在3种机匣处理中最强. 

关 键 词:压气机    自循环机匣处理    轴向位置    喷气    间隙泄漏流
收稿时间:2015/8/7 0:00:00

Mechanism of affecting ability of stability enhancement with varying axial position of self-recirculating casing treatment
ZHANG Hao-guang,AN Kang,TAN Feng,CHU Wu-li,WU Yan-hui.Mechanism of affecting ability of stability enhancement with varying axial position of self-recirculating casing treatment[J].Journal of Aerospace Power,2017,32(4):983-989.
Authors:ZHANG Hao-guang  AN Kang  TAN Feng  CHU Wu-li  WU Yan-hui
Abstract:The unsteady numerical investigation of three kinds of self-recirculating casing treatments was performed to explore the mechanism of affecting the ability of improving compressor stall margin with changing axial position of casing treatment(CT). Results showed that the ability of improving stall margin was best when the injecting part of CT was close to the blade tip leading edge, and also located in upstream blade inlet. The ability became low by changing the axial position of CT to make the injecting part above the blade tip leading edge. It became lower by moving the injecting part away from the blade tip leading edge along upstream direction, and the corresponding stall margin improvement gained with three kinds of casing treatments was 9.40%, 7.09% and 5.49% respectively. When the injecting part of CT was close to the blade tip leading edge, and located in upstream blade inlet, the level of positive effect created by CT was highest in the blade tip leading edge and the stall of rotor happened in this pivotal zone. Consequently the inlet blockage caused by the low energy tip clearance leakage flow was restrained most effectively, and the corresponding ability of increasing rotor stable operating range was highest among three kinds of casing treatments.
Keywords:compressor  self-recirculating casing treatment  axial position  injection  clearance leakage flow
本文献已被 CNKI 万方数据 等数据库收录!
点击此处可从《航空动力学报》浏览原始摘要信息
点击此处可从《航空动力学报》下载免费的PDF全文
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号