|
|||||
|
|
| TC4钛合金腐蚀加工速度和表面质量影响因素研究 | |
| 引用本文： | 林翠,刘枫,赵晴,文庆杰,杜楠. TC4钛合金腐蚀加工速度和表面质量影响因素研究[J]. 航空材料学报, 2008, 28(5) |
| 作者姓名： | 林翠 刘枫 赵晴 文庆杰 杜楠 |
| 作者单位： | 南昌航空大学,无损检测技术教育部重点实验室,南昌,330063;南昌航空大学材料科学与工程学院,南昌,330063;南昌航空大学材料科学与工程学院,南昌,330063;成都飞机工业,集团,公司工程制造部,成都610092 |
| 摘 要： | 研究了腐蚀溶液成分和工艺参数对TC4钛合金腐蚀加工速度、表面粗糙度和平整度的影响,利用扫描电镜观察了腐蚀加工前后的表面形貌.研究结果表明:氢氟酸浓度和溶液温度直接决定着腐蚀加工速度,随HF浓度和温度的增加,腐蚀加工速度升高.硝酸具有显著降低表面粗糙度的作用.溶液中的钛离子对腐蚀加工速度以及钛合金零件腐蚀后的表面质量有一定的影响,溶液中钛离子含量较低时,腐蚀加工速度较快,表面平整度较好,随钛离子含量的增加,腐蚀加工速度下降,表面不平整度增加.试样垂直吊挂时,定时翻转并搅拌可以得到均匀腐蚀的表面. |
| 关 键 词： | 钛合金 腐蚀加工 影响因素 |
Influencing Factors of Rate and Surface Quality of Corrosion Processing for TC4 |
|
| LIN Cui,LIU Feng,ZHAO Qing,WEN Qing-jie,DU Nan. Influencing Factors of Rate and Surface Quality of Corrosion Processing for TC4[J]. Journal of Aeronautical Materials, 2008, 28(5) | |
| Authors: | LIN Cui LIU Feng ZHAO Qing WEN Qing-jie DU Nan |
| Affiliation: | LIN Cui1,2,LIU Feng1,ZHAO Qing1,WEN Qing-jie3,DU Nan1,2(1.Department of Material Science , Technology,Nanchang Hangkong University,Nanchang 330063,China,2.Key Laboratory of Nondestructive Test of Chinese Ministry of Education,3.Department of Engineering Manufacture,Chengdu Aircraft Industrial Group Co.,Chengdu 610092,China) |
| Abstract: | In this paper,the influence of ingredients in corrosion solution and process parameters on corrosion rate,surface roughness and surface evenness for TC4 titanium alloy was discussed.Surface morphology was investigated by scanning electron microscopy before and after corrosion processing.The results show that HF concentration and solution temperature directly determined corrosion rate.The corrosion rate was promoted with increasing HF concentration and temperature.HNO3 can significantly reduce surface roughn... |
| Keywords: | titanium alloy corrosion processing influencing factor |
| 本文献已被 CNKI 维普 万方数据 等数据库收录！ | |