Effect of Counterface Material on Friction and Wear Behavior of Ni-Cr-W-Al-Ti-MoS_2 Composites

Ni-Cr-W-Al-Ti-MoS2 self-lubricating composites were prepared through the powder metallurgy (P/M) method. Their friction properties were investigated by a pin-on-disk tribometer in the range from the room temperature to 600 ℃. Alumina, silicon nitride and nickel-iron-sulfide alloys were selected as the counterface materials. Results indicate that the lowest friction coefficients under 0.22 can be obtained at 600 ℃ when rubbed against alumina. When rubbed against nickel-iron-sulfide alloys, are presented the lowest wear rates in the magnitude of 10-6 mm3/N·m, one order of magnitude lower than those when rubbed against ceramics. In the case of three rubbing pairs, the wear rates of the composite containing MoS2 present themselves inversely proportional to friction coefficients. With alumina ceramics used as a counterface, transfer films and glaze layers will form on the contact surface playing a main role in lubrication at high temperatures. However, when silicon nitride and nickel-iron-sulfide alloy are used, the lubricating transfer films appear not to be promi-nent.     

高性能涡轮发动机润滑系统设计

简述了润滑剂对发动机设计的影响。阐明了使用酯类润滑油的设计问题及润滑系统通用的设计要求。     

基于拟动力学的航空发动机主轴球轴承热弹流润滑分析

以航空发动机主轴球轴承高速高温重载典型工况为算例,基于轴承拟动力学分析,得到滚动体与套圈之间的微接触区运动和受力状态,分别用Hamrock-Dowson(H-D)拟合公式和翟文杰热修正公式计算了最小膜厚(MFT),同时结合热弹流润滑分析得到最小膜厚分布,对比了试验测试、H-D拟合、翟文杰热修正和热弹流润滑分析4种算法的最小膜厚,并根据膜厚比判定了轴承的弹流润滑状态.结果表明:H-D拟合和翟文杰热修正最小膜厚与试验测试结果相差较远,热弹流润滑分析结果与试验数据吻合性较好,误差10%以内;探讨了不同工况下的轴承弹流润滑性能.结果表明:存在径向载荷时,润滑膜整体压力增大,膜厚减小;随着转速增大,压力减小,膜厚增大,但是增大的趋势减缓.      

航空燃油齿轮泵滑动轴承非线性瞬态性能数值分析

为研究航空燃油齿轮泵滑动轴承在复杂交变载荷扰动下的瞬态润滑行为,建立了燃油齿轮泵滑动轴承的瞬态计算模型。该模型考虑了滑动轴承油膜空化边界的质量守恒和其所处非线性动态承载环境的影响。在此基础上使用批处理技术实现了燃油齿轮泵和滑动轴承的联合仿真计算,在滑动轴承的瞬态润滑计算过程中计入了燃油泵瞬态内流场和其动态载荷的耦合作用。以此进行了恒定载荷和动态载荷工况下的轴心轨迹稳定性分析以及轴承瞬态润滑性能分析研究。研究结果表明：滑动轴承计算模型的计算结果与实验数据较为吻合,误差保持1.2%以内;燃油齿轮泵的动态载荷对轴心轨迹的影响体现在轨迹启动段偏移的增大以及静平衡位置的消失;通过不同关键参数的对比研究发现：合理的增大宽径比或减小间隙比可以获得更为理想的轴心轨迹静平衡位置,但对于轴承转子运动的稳定性,间隙比由0.2%增至0.6%时,未稳定阶段轴心位置的变化趋势由双峰变为单峰,速度稳定段曲线的波动幅值先增大后趋于不变;当宽径比由0.6增至1.2时,全周期内速度响应曲线的偏移降低,轴心运行的稳定性提高;在轴承瞬态润滑特性中对于轴承载荷变化泄露流量具有的敏感性较强而最小油膜厚度的敏感性较差。     

环下润滑结构对径向收油环收油效率影响的数值计算研究

为研究环下供油润滑系统中的流动过程和收油环收油效率的影响因素及其影响规律,基于VOF(Volume of fluid)两相流模型和滑移网格模型的数值计算方法,建立了环下润滑系统内部流场的计算模型。通过数值计算,获得了收油环的收油效率并验证了数值计算结果的有效性,分析和探讨了不同结构参数对收油效率的影响。计算结果表明:利用本文数值计算方法得到的收油效率和流动现象与已有实验和数值计算结果均一致;供油喷嘴角度和收油环外径均主要影响滑油射流冲击收油叶片的飞溅量和收油叶片切割滑油量,收油效率取决于二者的相对大小,θ=0°,θ=9°和r0=2mm,r0=6mm时收油效率取极大值;收油叶片数量和供油喷嘴与收油叶片间距离分别影响收油叶片切割滑油射流的时间间隔和滑油射流在到达收油叶片前的流动,不影响滑油射流冲击收油叶片的飞溅量和收油叶片切割滑油射流的量,对收油效率的影响较小。     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

基于全局Newton-Raphaon方法的弹流润滑分析

基于全局Newton-Raphaon方法对滑动轴承的弹流润滑性能进行了数值摸拟。比较了弹性变形对连杆大头轴承最小油膜厚度和最大油膜压力的影响。结果表明:全局Newton-Raphaon方法很好的解决了收敛困难,程序运行时间长的问题;考虑表面弹性变形的连杆大头轴承与刚性轴承相比,最小油膜厚度与最大油膜压力的变化趋势相同;一个工作循环内,弹性轴承的最小油膜厚度略大于刚性轴承,而最大油膜压力则明显减小。     

滚珠自转对高速球轴承环下润滑内部流动的影响

高速球轴承正常工作时,处于高速旋转状态,此时油相和气相因重力和离心力的作用在轴承环间剧烈运动。为了更准确地分析轴承环间的两相流动,采取VOF模型进行内部流场的模拟,采用多重旋转坐标系描述部件运动。建立球轴承环下润滑计算模型,分析了考虑滚珠自转因素下轴承内部的流动,并在此基础上探究了转速及供油量对轴承工作状态的影响。结果表明,对比整体模型与滚珠自转模型,发现滚珠自转使得轴承内部油体积分数增大,同时也使得滑油穿透间隙达到外环的能力增加;在考虑滚珠自转情况下,转速的不断增大,使得轴承内部的油相体积分数不断减小,在低转速情况下滚珠自转对流体运动影响较为明显,在高转速情况下公转速度对流体运动起到主导作用,滚珠自转对流体运动影响减弱;供油量不断的增大,使得滚珠自转模型内部的油相体积分数也在不断增大,而且滚珠自转运动会加强滑油在轴承内部的分布。     

非牛顿大滑滚比工况的斜齿轮热摩擦特性分析

考虑啮合过程中接触线长度及齿面载荷的时变性,结合沿接触线方向综合曲率半径及卷吸速度的瞬态特点,建立满足航空传动润滑剂非牛顿流体及大滑滚比工况的有限长线接触斜齿轮热弹流润滑(TEHL)模型。采用多重网格法及逐列扫描法,获得适用于宽泛工况范围的斜齿轮热弹流润滑完全数值解;分析非牛顿及大滑滚比情形下的斜齿轮传动热摩擦特性。结果表明:斜齿轮端部存在明显压力及温度尖峰,且离入口愈近膜厚会略减小;非牛顿特性对温度场影响显著,且接触线过节点时温度分布呈“V”型分布;摩擦因数沿啮合线方向在节点处接近于0且向两侧逐渐增大,同时随滑滚比的增大而增大。      

浅谈波音737NG飞机APU滑油系统一项监控指标在故障监控中的应用

波音737NG飞机APU故障影响航班运行,而APU滑油系统是其安全运行的重要保障,大多数APU的故障都能够从滑油系统的监控指标中找到故障征兆。本文基于737NG飞机APU滑油系统工作原理,提出了一项APU滑油系统的监控指标——温升速率,并利用该指标总结排故方法进行重点故障的监控,有效地提高了排故效率。