排序方式: 共有20条查询结果,搜索用时 448 毫秒
1.
Al_2O_3(YAG)/LaPO_4层状陶瓷复合材料研究 总被引:2,自引:0,他引:2
选择Al2O3(YAG)作为基体片层材料,LaPO4作为界面层材料,采用凝胶注模成型技术制备出基体层材料的坯片,然后在基体层坯片上采用浸渍或喷涂工艺附着界面层材料,最后将坯片叠置于模具中热压烧结.制备的陶瓷复合材料微观结构均匀,基体片层厚度为110-150μm,界面层厚度为10~30μm,实测层厚比为11.重点研究工艺参数及界面层成分对层状陶瓷复合材料室温性能的影响.结果表明,氧化物基层状陶瓷复合材料的抗弯强度比基体材料略有下降,但室温断裂韧性达到了13.52MPa·m1/2,是基体材料断裂韧性的3倍.对比氧化物基层状陶瓷复合材料与基体材料在断裂过程中裂纹扩展路径的差异. 相似文献
2.
3.
以Al(NO3)3乙醇溶液为电解液,利用阴极微弧电沉积技术在纯钛表面制备了较厚的氧化铝涂层.分析了涂层的形貌、成分和相组成,测试了涂层的抗高温氧化、电化学腐蚀及抗热震性能,并探讨了阴极微弧沉积氧化铝涂层的机理.涂层由γ-Al2O3和少量的α-Al2O3组成.涂层中含有少量的钛元素,表明涂层/钛界面附近的钛基体在微弧放电作用下也参与氧化铝涂层的沉积和烧结过程.涂层经过100次(700 ℃水淬)热循环后仍与钛基体结合良好.700 ℃恒温氧化结果表明,具有氧化铝涂层的钛氧化速率降低了4倍. 相似文献
4.
陶瓷超材料吸波器具有耐高温、高强度、可完美吸波的特点,其结构复杂且具有周期性,是一种新兴的吸波器件.但传统成形方式在复杂结构制造上存在一定的局限性.本文提出一种基于光固化增材制造氧化铝陶瓷表面镀铁氧体的方法实现周期性复杂结构的陶瓷超材料吸波器.使用氧化铝粉末和光敏树脂,配制出可供3D打印的氧化铝陶瓷浆料,利用3D打印机... 相似文献
5.
6.
7.
8.
JING Mao-xianga * SHEN Xiang-qiana ZHOU Jian-xina LI Dong-hongb LI Wang-xingb aSchool of Materials Science Engineering Jiangsu University Zhenjiang China bZhengzhou Research Institute of Chalco Henan Zhengzhou China 《中国航空学报》2006,19(Z1)
Alumina-based composites containing 0-15wt% Ni metallic phase were produced by hot press-sintering Ni-coated alumina pow-ders. The Ni-coated alumina powders were prepared by the aqueous heterogeneous precipitation of alumina micro-powders and nickel sulfate salt followed by reduction process. The microstructural features and dispersion of Ni phase in Ni-coated alumina powders and the subsequent alumina-Ni cermets were investigated using scanning electron microscope (SEM), X-ray diffractometer (XRD), and trans-mission electron microscope (TEM). The relative density of the hot press-sintered composites was measured with the Archimedes’ method while the fracture strength and the fracture toughness were defined with the three-point bending method and the mi-cro-indentation fracture method. In the formation of alumina-Ni cermets from sintered Ni-coated alumina powders, Ni phase to some extent limits the densification rate and stifles the coarsening and growing process of alumina grains. The Ni phase is found to be located at the interfaces and the triple-joint junctions of alumina grains which results into alteration of the fracture mode of alumina and its in-creased fracture strength and fracture toughness if compared with monolithic alumina. 相似文献
9.
钛材料主要指钛合金、钛铝金属间化合物和钛基复合材料,具有密度低、强度高、抗氧化与蠕变性能好等优异特性,在航空发动机领域具有广泛应用前景。钛材料属于典型的难加工材料。磨削是高效精密加工钛材料的重要方法,可以获得良好的加工精度和表面质量。首先概述了钛材料在航空发动机中的应用及其磨削工艺技术总体情况。随后,从磨削力与磨削温度、砂轮磨损、材料去除机理、表面完整性等方面阐述了钛材料磨削技术的研究进展,并总结了针对钛材料磨削关键问题提出的新工艺和新方法。最后,对钛材料磨削技术未来的研究方向进行了展望。 相似文献
10.
Al2O3陶瓷的损伤型本构关系研究 总被引:1,自引:0,他引:1
利用INSTRON材料试验机和SHPB(分离式Hopkinson压杆)对Al2O3陶瓷材料进行了单轴压缩实验,测量了材料在不同应变率下的应力和真实应变。实验结果表明,Al2O3陶瓷是应变率敏感材料。通过对准静态和高应变率下的实验结果分析,认为损伤型ZWT非线性粘弹性本构关系能较好地描述Al2O3陶瓷在不同应变率条件下的力学行为,用遗传算法确定了本构关系中的参数。研究表明,所用损伤型ZWT本构方程和用遗传算法确定的参数在10-4-102s-1应变率范围内与实验结果吻合较好。 相似文献