轨控大干扰下的系统角动量管理

摘要： 针对利用角动量交换装置系统实现轨控期间姿态维持的情况，研究当轨控推力器存在大力矩扰动时系统角动量管理方法.结合对地运行航天器轨道运动特性，分析轨控干扰力矩的积累角动量变化规律；考虑角动量管理装置系统的角动量存贮容量，基于角动量积累规律提出了一种结合偏置角动量建立与对称分布轨控位置选择的系统角动量管理方法，实现了对称轨控位置积累角动量互相抵消的自平衡效果，极大程度地提高轨控效率且避免系统角动量饱和现象.所提出的方法适用于喷气欠驱动控制系统，方法的有效性通过了数学仿真验证及在轨型号应用.     

单向电永磁作动器结构优化与动态特性分析

针对电磁作动器的使用要求，设计出一种具有能耗低、吸力大及响应快等特点的新型单向电永磁作动器。结合有限元仿真软件，利用有限元法研究作动器的结构参数如铁芯齿形结构、平面结构、无永磁结构、铁芯的倾斜角度及衔铁位移（气隙厚度）等因素对作动器电磁吸力和响应速度的影响。结果表明，电磁吸力随着作动衔铁位移的增加而大幅度减小；倾角结构的铁芯设计能使作动器性能达到最佳，且铁芯的倾斜角度为50°时，电磁吸力有最大值3071N。     

污水处理装置在冶金行业中的应用

对污水处理装置的技术参数、技术要求及设计方案的选择、工作原理做了进一步的阐述。对工业循环冷却水的处理有实际指导意义。     

新建他激反激变换器方程及其解析解

引用文 [1 ]的思路 ,寻找他激反激变换器的运行状态特征参量 (磁通密度增量、剩余磁通密度和占空比 )与构成这一变换器的基本物理参量之间的函数关系。首先阐明由于频率给定 ,他激反激变换器稳态运行时会出现无剩磁工况和有剩磁工况两种。而后确定这两种工况下 ,磁路等效储能空间单位体积每个周期的传输能量 (命名为“磁能传输密度”)。在这基础上 ,分别建立和解出他激反激变换器在不同工况下稳定运行时应满足的方程。最后根据所得的解析解阐明这种变换器的特性。本文和文 [1 ],以磁路分析为基础建立了一种新的反激变换器理论。     

Investigation of the differential rotation of the large-scale magnetic elements for the solar activity cycles 20 and 21

The differential rotation of the patterns of the large-scale solar magnetic field during solar activity cycles 20 and 21 is investigated. Compact magnetic elements with the polarity of the general solar magnetic field have larger speed of rotation than the elements with the opposite polarity. The surface of the Sun was divided by 10°-zones. In all of them the average rotation rate of the magnetic elements with negative polarity is little higher than that of the magnetic elements with positive polarity, except for 50°-zone of the south hemisphere and at the 10° latitude of the north hemisphere.

The rates of differential rotation for large-scale magnetic elements with negative and positive polarities have similar behavior for both cycles of the solar activity.

The rotation rate varies at polarity reversal of the circumpolar magnetic fields. For the cycle No 20 in 1969–1970 the threefold reversal took place in the northern hemisphere and variations of rotation rate can be noticed for magnetic elements both with positive and negative polarity for each 10°-zone in the same hemisphere.     

Reconstructed 3-d magnetic field structure and hard X-ray two ribbons for 2000 Bastille-day event

The Bastille-day event in 2000 produced energetic 3B/X5.6 flare with a halo CME, which had great geo-effects consequently. This event has been studied extensively and it is considered that it follows the two-ribbon flare model. The flare/CME event was triggered by an erupting filament and TRACE observations showed formation of giant arcade structures during the flare process. Hard X-ray (HXR) two ribbons revealed for the first time in this flare event (Masuda et al., 2001). The reconstruction of 3-D coronal magnetic fields revealed a magnetic flux rope structure, for the first time, from extrapolation of observed photospheric vector magnetogram data and the flux rope structure was co-spatial with portion of the filament and a UV bright lane (Yan et al., 2001a, 2001b). Here we review some recent work related to the flux rope structure and the HXR two ribbons by comparing their locations and the flux temporal profiles during the flare process so as to understand the energy release and particle accelerations. It is proposed that the rope instability may have triggered the flare event, and reconnection may occur during this process. The drifting pulsation structure in the decimetric frequency range is considered to manifest the rope ejection, or the initial phase of the coronal mass ejection. The HXR two ribbons were distributed along the flux rope and the rope foot points coincide with HXR sources. The energy dissipation from IPS observations occurred within about 100 R _⋅ is consistent with the estimate for the flux rope system. This revised version was published online in August 2006 with corrections to the Cover Date.     

一个简单有效的磁记录纠错系统

介绍一种简单有效的纠错编码方法 ,用于资源卫星高密度数字磁记录器 ,使误码率由 10 -6降低到 10 -11,同时介绍它的基本工作原理、实现方案及试验结果。     

电励磁双凸极电机调速系统的原理与实现

介绍了新型电励磁双凸极电机的结构和原理，然后结合全桥变换器阐述了电励磁双凸极电机的控制方法，接着详细介绍了电励磁双凸极电机转速、电流双闭环控制调速系统的原理和实现方法，最后以一台500W12/8极电励磁双凸极电机调速系统为例进行了系统实验。实验结果表明，电励磁双凸极电机调速系统具有结构简单、控制方便和良好的动静态性能。     

高强度钢内螺纹冷挤压成形与强化试验研究

内螺纹冷挤压成形是提高内螺纹疲劳强度的有效方法.作者研制出挤压扭矩和温度的测量系统,并从理论上证明了挤压变形区金属在挤压过程中受到三向压应力的作用,这可以大大增加金属的塑性,改善内螺纹的成形条件.高强度钢内螺纹成形与强化的关键在于挤压丝锥结构的优化设计以及工件底孔尺寸、挤压速度和冷却润滑液的合理选择.疲劳对比试验结果表明:在两个不同应力水平下,用挤压丝锥挤压强化的300M高强度钢螺纹,其寿命是切削螺纹的4～30倍.     

空空导弹惯性开关中圆周磁场对导弹性能的影响

为了提高空空导弹的作战效能和可靠性,由弹载电源向开关电路进行大电流放电,可提高惯性开关中圆柱电极上周磁场的强度,增强抵抗磁钢对钢珠反向作用力的能力,当导弹撞击目标过载较小时,使惯性开关的导通时间也能够满足触发电路工作需要,因此,导弹遇目标不炸的故障概率可得到下降。