Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

CFRP反射器型面主动控制和作动器位置优化

研究了运用压电陶瓷作动器对碳纤维增强复合材料（CFRP）格栅反射器的型面主动控制。首先，采用了一种具有独立电压自由度的梁单元，以及考虑高阶剪切变形的板单元，对主控格栅反射器进行有限元建模；运用能量变分哈密尔顿原理推导了主控格栅反射器的有限元控制方程，并给出了反射面型面残余均方根（RMS）误差最小的电压最优控制方法。然后，研究了在典型载荷下，反射面残余RMS误差最小的PZT作动器位置分布的优化配置问题；提出了一种将遗传算法和梯度投影方法相结合的改进优化方法，用来求出在限定作动器数量的条件下，作动器几何位置的优化配置，使控制后反射面的残余RMS误差最小；给出的数值算例验证了方法的正确性和有效性。最后，研制了格栅反射器型面主动控制的实验样机，针对反射器的初始制造误差进行了型面主动控制，验证了控制方法的可行性和有效性。     

Implementation of tactical maneuvers with maneuver libraries

This study creates and combines the general maneuver libraries for fixed-wing aircraft to implement tactical maneuvers. First, the generalized maneuver libraries are established by analyzing the characteristics of tactical maneuvers required in battlefields. The 7th order polynomial is applied to both the creation of the maneuver libraries and the generation of the trajectories or flight paths for modal inputs. To track the desired trajectory, we design the Attitude Command Attitude Hold (ACAH) system and the Rate Command Rate Hold (RCRH) system using Model Following Controller (MFC). Moreover, the Line-of-Sight (LOS) guidance law is designed. In particular, the CONDUIT® is employed to optimize the gains so that the control systems meet the aircraft Handling Qualities (HQ) criteria. Finally, flight simulations are performed for the longitudinal loop, immelmann-turn, and climb-slalom-descent maneuvers to verify that tactical aggressive maneuvers are realizable via the combination of maneuver libraries. This study can contribute to the development of flight techniques for aircraft tactical maneuvers and to the revision of air force operational manuals.     

单向电永磁作动器结构优化与动态特性分析

针对电磁作动器的使用要求，设计出一种具有能耗低、吸力大及响应快等特点的新型单向电永磁作动器。结合有限元仿真软件，利用有限元法研究作动器的结构参数如铁芯齿形结构、平面结构、无永磁结构、铁芯的倾斜角度及衔铁位移（气隙厚度）等因素对作动器电磁吸力和响应速度的影响。结果表明，电磁吸力随着作动衔铁位移的增加而大幅度减小；倾角结构的铁芯设计能使作动器性能达到最佳，且铁芯的倾斜角度为50°时，电磁吸力有最大值3071N。     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

H5飞机调油方法研究

对Ｈ５飞机经过了计算、论证、试飞，在此基础上提出了一种既安全又能充分发挥飞机飞行性能，同时又使动作程序化的调油方法－－规划调油法。用这种调油就可以大大地减少飞行员操纵飞机进的注意力分散，更利于集中精力操纵飞机，以保证飞行的安全。     

推进我国企业债券利率市场化的措施

企业债券利率市场化是我国利率市场化改革的重要组成部分。目前,我国已经基本具备了企业债券利率市场化的条件,宏观经济环境稳定,微观经济主体日趋理性,国债和金融债券发行利率市场化也为下一步实现企业债券发行利率市场化提供了宝贵的经验。鉴于此,可以根据企业债券融资发展的不同阶段,采取相应措施加快我国企业债券利率市场化的步伐,主要包括:取消发债企业的所有制限制、培育企业债券流通市场、逐步取消发债规模限制、放宽发行利率的浮动幅度、健全企业债券风险监管制度、规范企业债券信用评级。     

用亚稳态正电子素研究络合的瞬态反应（Ⅲ）

本文用自制的装有 BaF_2探头的高探测效率的正电子湮没寿命谱仪测量了在室温下正电子素 o-Ps 与 p-RPhG 及 m-RPhG(R=NO_2,Cl,H,CH_3,cH_3O)在20%(V/V)二氧六环水溶液中的络合形成速度常数。实验结果表明,这些o-Ps-M 络合形成速度常数 K 值均与作为配位体的 p-RPhG、m-RPhG 的碱性解离常数 K 的负对数 pK_2 呈线性函数。这表明上述瞬态络合反应满足线性自由能关系,由此可推断出上述络合反应的一些重要性质。     

高燃速丁羟推进剂配方研究

通过多种途径的试验,对高燃速丁羟推进剂配方进行了研究.试验结果表明,采用超细防结块氧化剂和液固组合燃速催化剂能使推进剂的燃速达到70mm/s以上(在6.864Mpa压强下);采用组合工艺助剂可改善推进剂工艺性能.本推进剂燃烧稳定,压强指数和温度敏感系数较低,力学性能良好,为高燃速推进剂的研制奠定了良好的基础.     

X射线探伤机空气比释动能率测量不确定度评定

基于X射线探伤机空气比释动能率测量的数学模型，对其测量不确定度进行了评定。