Third-Order Loop Filter Design for Acceleration-Rate Tracking

A perfect third-order loop filter design that can be implemented as a digital filter is obtained which minimizes the noiseless steady-state acceleration rate (jerk) error for a fixed loop noise bandwidth. Simulations were performed to obtain transient responses of the third-order loop plus a sample fourth-order loop under a jerk input. The results enable one to obtain a loop design that minimizes the loop noise bandwidth required for a given steady-state jerk error and thus obtain better noise jitter performance.     

Analysis of the linear amplifier/analog-digital converter interfacein a digital microwave receiver

An analysis of the relationship between a linear amplifier chain and an analog-to-digital converter (ADC) in a digital microwave receiver, with respect to sensitivity and dynamic range issues, is presented. The effects of gain, third-order intermodulation products and ADC characteristics on the performance of the receiver are illustrated and design criteria for the linear amplifier chain (given a specified ADC) are developed. A computer program is included which calculates theoretical receiver performance based on gain and third-order intermodulation product selections. Experimental results are also presented and compared with theoretical values     

A noise insensitive solution to an ambiguity problem in spectralestimation

The instantaneous frequency measurement (IFM) receiver is capable of measuring the center frequency of single frequency pulses over a wide range (bandwidth) of center frequencies. Because of various constraints, the frequency resolution requirement results in long correlator delay times that reduce the single correlator bandwidth. A large bandwidth can be achieved only if two or more correlators are used. The problem of estimating frequency is then reduced to the simultaneous congruence problem of number theory. A design procedure is presented for solving the congruence problem for a given amount of noise protection, a stated frequency resolution, a minimum bandwidth, and a fixed level of precision (bits) in the IFM receiver     

Reduction of aliasing ambiguities through phase relations

A method for digital determination of a single frequency from a sine wave sampled at less than the Nyquist rate is discussed. The method makes use of phase shift information to eliminate the aliasing ambiguity. Multiple sampled data are required to eliminate ambiguity completely. Computer modeling using simulated data corrupted by uncorrelated Gaussian noise was used to verify the approach. The results demonstrate that the frequency of an input sine wave can be correctly identified. This approach can be applied to electronic warfare (EW) receivers to increase their input bandwidth     

Resolution of a 2π ambiguity problem in multiple frequencyspectral estimation

An algorithm is proposed to resolve a fundamental 2π ambiguity problem occurring in multiple frequency spectral estimation. Given M frequencies f_m, and I separate frequency estimators with unambiguous bandwidths F_i, the ambiguity problem can be stated as solving for the fm, given the estimator outputs, α_mi, (1⩽m⩽M;1⩽i⩽I) where f_m=α_mi+K_miF_i and K_mi is some integer. The proposed algorithm exhaustively resolves all possible α_mi groupings into single frequency values using a noise insensitive technique that exchanges system bandwidth for noise protection. The correct multiple frequencies are then defined as the single frequencies that repeat a specified number of times. A complete analysis is included     

Software approach to access UWB interference on GPS receivers

Ever since the FCC approved the use of UWB devices in commercial and federal bands, various agencies whose operations and/or products rely on the integrity of signals within certain "restricted" radio frequency bands have voiced concerns over the potential impact of the UWB interference. GPS signals are among these "restricted" bands. Several groups in the GPS community have conducted experimental studies concerning the impact of UWB interference on the performance of various grades of commercial and aviation GPS receivers. In this paper, we present a software approach to simulate and evaluate UWB interference on GPS receivers. The software approach provides greater flexibility in the design of testing scenarios, such as the inclusion of a large number of aggregated UWB devices, the generation of new UWB signals and modulation schemes, and the possibility of extending the study to new GPS signals. The paper discusses a general framework for developing algorithms to evaluate UWB and GPS interference under a wide variety of hardware and software conditions. This framework consists of three classes of components: input, processing, and analysis. The input components are responsible for the generation of UWB signal waveforms and modulation schemes, and GPS signals. The processing components include a simulated model of GPS RF front end and software implementation of GPS processing blocks, such as acquisition, tracking, and post-processing. The analysis components focus on the study of specific receiver processing component outputs. Both real and simulated UWB signals can be used in the study. The real UWB signals are primarily used to validate the simulation procedure, whereas the simulated UWB signals are used to allow the immediate incorporation of new UWB waveforms and modulations in the evaluations. This paper presents details of the software components developed and the preliminary results achieved