Enhanced resolution in simple radars

Many simple radars use fact-risetime pulses, but wide bandwidth does not translate into corresponding high resolution since the spectrum is far from flat. A scheme for enhancing down- and cross-range resolution of multiple targets through a two-step partial equalization of the spectrum is illustrated by detailed computer simulation, with emphasis on the tradeoffs between resolution and signal-to-noise ratios. Three examples are treated: two equal scattering centers, two unequal scattering centers, and compound target     

A methodology for evaluating, comparing, and selecting softwaresafety and reliability standards

The regulated industries, which in the FDA's (US Food and Drug Administration) case include the manufacturers of food, cosmetics, pharmaceuticals, and medical devices, are responsible for selecting and justifying the selection and use of appropriate national and/or international consensus standards. This paper documents the results of a scientific inquiry which was undertaken to develop a methodology to evaluate and select individual standards as well as compatible sets of standards. Initially the scope was limited to software safety and reliability standards. Since then it has been expanded to other areas. It was found that six categories of criteria are important when evaluating the potential use of software safety standards: General Factors, Product Characterization, Process Characterization, Personnel Characterization, Risk Management, and Overall Standards Framework. The criteria in each of the six categories must be addressed, How they are addressed is both a technical and a policy decision. The goal should not be to try to find the “ultimate” standard because there isn't any. Rather the goal should be to select a balanced “diet” of standards based on these six categories. The methodology provides a systematic framework from which to make an objective determination about the appropriateness of using a particular standard     

The Engineering Radiation Monitor for the Radiation Belt Storm Probes Mission

An Engineering Radiation Monitor (ERM) has been developed as a supplementary spacecraft subsystem for NASA’s Radiation Belt Storm Probes (RBSP) mission. The ERM will monitor total dose and deep dielectric charging at each RBSP spacecraft in real time. Configured to take the place of spacecraft balance mass, the ERM contains an array of eight dosimeters and two buried conductive plates. The dosimeters are mounted under covers of varying shielding thickness to obtain a dose-depth curve and characterize the electron and proton contributions to total dose. A 3-min readout cadence coupled with an initial sensitivity of ～0.01 krad should enable dynamic measurements of dose rate throughout the 9-hr RBSP orbit. The dosimeters are Radiation-sensing Field Effect Transistors (RadFETs) and operate at zero bias to preserve their response even when powered off. The range of the RadFETs extends above 1000 krad to avoid saturation over the expected duration of the mission. Two large-area (～10 cm²) charge monitor plates set behind different thickness covers will measure the dynamic currents of weakly-penetrating electrons that can be potentially hazardous to sensitive electronic components within the spacecraft. The charge monitors can handle large events without saturating (～3000 fA/cm²) and provide sufficient sensitivity (～0.1 fA/cm²) to gauge quiescent conditions. High time-resolution (5 s) monitoring allows detection of rapid changes in flux and enables correlation of spacecraft anomalies with local space weather conditions. Although primarily intended as an engineering subsystem to monitor spacecraft radiation levels, real-time data from the ERM may also prove useful or interesting to a larger community.     

First results of the growing of PbTe single crystals under microgravity conditions

Two sublimation experiments with PbTe were performed at 850°C and 750°C under microgravity conditions during the “Salyut-6”-“Soyuz-31” mission in 1978. The sublimation took place on the (100)-face of a PbTe crystal. The condensate grown at 850°C shows in the upper part the formation of a pyramidal habit. The bulk consists of parallel growth colums with [100]-boundary faces. The charge carrier concentration of the electrons (N=1,5·10¹⁹ cm^?3) is higher than the homogeniety limit for 800°C should permit. This is in contrast to the result obtained on the PbTe crystal of the parallel experiment on the earth. At 750°C a laminated condensate is grown with a low growth rate. The microphotograph of the substrate shows the beginning whisker formation according to the VLS-mechanism.     

Bioinstrumentation for evaluation of workload in payload specialists: results of ASSESS II

ASSESS II (Airborne Science/Spacelab Experiments System Simulation) was a cooperative NASA-ESA project which consisted of a detailed simulation of Spacelab operations using the NASA Ames Research Center CV-990 aircraft laboratory. The Medical Experiment reported on in this paper was part of the complex payload consisting of 11 different experiments. Its general purpose was to develop a technology, possibly flown on board of Spacelab, and enabling the assessment of workload through evaluating changes of circadian rhythmicity, sleep disturbances and episodical or cumulative stress. As parameters the following variables were measured: Rectal temperature, ECG, sleep-EEG and -EOG, the urinary excretion of hormones and electrolytes. The results revealed evidence that a Spacelab environment, as simulated in ASSESS II, will lead to internal dissociation of circadian rhythms, to sleep disturbances and to highly stressful working conditions. Altogether these effects will impose considerable workload upon Payload Specialists. It is suggested that an intensive pre-mission system simulation will reduce these impairments to a reasonable degree. The bioinstrumentation applied in this experiment proved to be a practical and reliable tool in assessing the objectives of the study.