Scientific objectives and payloads of Tianwen-1, China’s first Mars exploration mission

This paper describes the scientific objectives and payloads of Tianwen-1, China’s first exploration mission to Mars. An orbiter, carrying a lander and a rover, lifted-off in July 2020 for a journey to Mars where it should arrive in February 2021. A suite of 13 scientific payloads, for in-situ and remote sensing, autonomously commanded by integrated payload controllers and mounted on the orbiter and the rover will study the magnetosphere and ionosphere of Mars and the relation with the solar wind, the atmosphere, surface and subsurface of the planet, looking at the topography, composition and structure and in particular for subsurface ice. The mission will also investigate Mars climate history. It is expected that Tianwen-1 will contribute significantly to advance our scientific knowledge of Mars.     

多臂空间机器人的视觉伺服与协调控制

针对多臂空间机器人自主目标抓捕任务，首先建立多臂空间机器人的运动模型和其与目标的相对运动模型，采用Kane方法建立多臂空间机器人的动力学模型；其次，研究基于视觉伺服的机械臂在线轨迹规划算法，并引入零反作用机动，消除机械臂运动对平台姿态的扰动；再次，在不使用零反作用机动功能时，分别使用基于角动量前馈补偿的协调控制算法和逆动力学方法设计了协调控制器，在机械臂运动时保持平台姿态和相对目标的位置。最后，开发了基于Matlab的仿真软件MASS（多臂空间机器人仿真），仿真结果校验了上述方法的有效性。     

Early analysis of precise orbit and clock offset determination for the satellites of the global BeiDou-3 system

Eight new-generation BeiDou satellites (BeiDou-3) have been launched into Medium Earth Orbit (MEO), allowing for global coverage since March 2018, and they are equipped with new hydrogen atomic clocks and updated rubidium clocks. Firstly, we analyzed the signals for the carrier-to-noise-density ratio (C/N0) and pseudorange multipath (MP) by using international GNSS (Global Navigation Satellite System) Monitoring and Assessment System (iGMAS) station data, and found that B1C has a lower C/N0, and B2a has the same level of C/N0 as the B1I and B3I signals. For pseudorange multipath, compared with the BeiDou-2 satellites, the obvious systematic variation of MP scatters related to the elevation angle is greatly improved for the BeiDou-3 and BeiDou-3e satellites signals. For the signals of the BeiDou-3 satellites, the order of the Root Mean Square (RMS) values of multipath and noise is B3I?<?B1I?<?B2a?<?B1C. Then, the comparison of the precise orbit determination and clock offset determination for the BeiDou-2, BeiDou-3, and BeiDou-3 experimental (BeiDou-3e) satellites was done by using 10 stations from iGMAS. The 3D precision of the 24?h orbit overlap is 24.55, 25.61, and 23.35?cm for the BeiDou-3, BeiDou-3e, and BeiDou-2 satellites, respectively. BeiDou-3 satellite has a comparable precision to that of the BeiDou-2 satellite. For the precision of clock offset estimation, the Standard Deviation (STD) of the BeiDou-3 MEO satellite is 0.350?ns, which is an improvement of 0.042?ns over that of the BeiDou-2 MEO satellite. The stabilities of the BeiDou-3 and BeiDou-3e onboard clocks are better than those of BeiDou-2 by factors of 2.84 and 1.61 at an averaging time of 1000 and 10,000?s, respectively.     

高主流湍流度下密度比对涡轮导叶全气膜冷却特性的影响

为了研究高主流湍流度下二次流密度比对涡轮导叶全气膜冷却特性的影响,使用热色液晶测量了在主流湍流度为15%,二次流密度比为1.0和1.5下三维涡轮导叶的气膜冷却效率和换热系数。二次流与主流质量流量比为7.0%和12.5%。结果表明:二次流密度比增大可以降低冷气射流的动量,小流量比工况下,在叶片前缘和压力面前半段,动量较低的二次流在高主流湍流度的影响下更易耗散,增大二次流密度比使冷却效率明显降低;大流量比工况下,二次流动量降低使气膜孔后区域冷气贴附性增强,气膜冷却效率和冷气覆盖效果均得到提升。小流量比工况下,二次流密度比增大对叶片表面换热的影响较小;大流量比工况下,二次流密度比增大使吸力面中弦区域和压力面后半段的平均换热系数比分别降低15%和25%。     

涡轮导向叶片综合冷却效率实验研究

为了研究流动参数对涡轮导向叶片综合冷却效率的影响,采用红外热像仪对叶片表面的温度分布进行了测量,得到了叶片的综合冷却效率随流量比、温比、主流进口雷诺数和湍流度的变化规律。实验过程中,次流与主流的流量比分别为0.15,0.18,0.20,0.22和0.24;主次流温比分别为1.4,1.7,1.93和2.2;主流进口雷诺数分别为1.0×10~5,1.1×10~5,1.2×10~5,1.3×10~5和1.4×10~5;主流进口湍流度分别为0.506%,8.156%,14.92%。结果表明,综合冷却效率在前缘处最低,沿流向逐渐升高;增大流量比会显著提高叶片的综合冷却效率,在温比为1.93时,流量比由0.15增大至0.24,综合冷却效率平均增加29.3%;温比和主流进口湍流度的增大均不利于综合冷却效率的提升,流量比为0.20时,温比由1.4增大至2.2,综合冷却效率平均下降46.5%,湍流度由0.506%增大至14.92%,综合冷却效率平均降低15.5%;主流进口雷诺数对叶片综合冷却效率的影响很小。     

盖板式预旋系统的压比和熵增特性

对预旋系统内的压力变化相关研究较少。基于理论分析、实验测量以及数值计算,对某盖板式预旋系统的压比及熵增特性进行研究。通过理论推导,对预旋系统内压比与无量纲温降的关系进行分析。在最高转速可达10000r/min的高转速实验台上,测量了转盘上的气流静压以及相对总温,进而获得压比及熵增特性。进行三维数值计算,将数值计算结果与实验结果进行了对比,并根据数值计算结果对预旋系统内的熵产分布以及各元件的熵增情况进行分析。结果表明:系统温降以及旋转马赫数大小决定了预旋系统的理想最大压比,而实际压比与理想压比的比值取决于系统内的熵增大小。采用数值计算以及实验测量所得结果对理论关系式进行了验证,最大偏差2.7%。旋转马赫数一定的条件下,随系统无量纲温降增大,系统压比逐渐减小。由于熵增影响,实测压比与理想压比最大相差约36%。预旋系统内的熵增主要发生在预旋腔静止壁面、接受孔前后、供给孔进口等气流旋转比发生剧烈变化的区域。预旋系统内主要元件的熵增随流量增大都呈逐渐增大的趋势,但接受孔处熵增最小值出现在喷嘴出口旋转比等于1左右时,流量过小或过大都会导致接受孔处熵增变大。     

基于两相流模型的挤压油膜阻尼器空化流场特性数值模拟

基于气液两相流理论中的Mixture模型和Zwart-Gerber-Belamri空化模型,采用动网格技术建立了两端开口中心槽供油型挤压油膜阻尼器三维非定常空化流场求解模型。数值模拟表明:随着阻尼器内环进动,考虑两相流动的油膜低压区在中心槽的两侧产生两道对称的条状负压带,条状带内具有较高的气相体积分数;阻尼器低压区的压力和气相体积分数对进油孔位置十分敏感,阻尼器油膜力和流场气穴比的变化频率与进油孔数密切相关。内环同心进动半径、进动频率对阻尼器空化流场影响的数值计算表明,进动半径和频率的增大均会使得流场内的空化现象加剧,同时气穴比的相位滞后现象愈加显著。      

一种基于张氏标定法的单目相机改进标定算法

单目视觉在地面机器人等无人导航系统中的应用越来越广泛，而相机参数的标定是利用视觉进行导航的基础性工作。标定结果的好坏，直接影响导航性能和定位精度。主要考虑单目相机的径向畸变，基于张正友平面标定法，通过利用Matlab进行图像预处理、利用OpenCV进行Harris角点检测和亚像素精确化等方法在角点提取精度等方面进行了改进，通过重投影法对标定结果进行了评估，并将其与Matlab相机标定工具箱Toolbox_calib所得结果进行了比较。实验结果表明，改进的标定算法标定结果精度更高，并且对多个摄像头传感器均有效，适用性强。     

Potential of IRNSS/NavIC L5 signals for ionospheric studies

Indian Space Research Organization (ISRO) has developed an indigenous system named Indian Regional Navigation Satellite System (IRNSS) or NavIC (Navigation with Indian Constellation), that consists of 7 satellites and transmits navigation signal in L and S bands. ISRO, for validation of the system, has installed many IGS (IRNSS/GPS/SBAS) receivers scattered over the Indian region. Using preliminary data from two geographically widely separated stations over India, this paper presents the results on studies on parameters of IRNSS signal quality and discusses how these parameters may be used to study the ionospheric behavior over the Indian region. The results show the importance and advantages of using IRNSS data for such studies.     

纵向波纹隔热屏气膜冷却特性实验

针对加力燃烧室纵向波纹隔热屏气膜冷却效果开展了细致的实验研究,利用红外热像仪测量了隔热屏壁面的温度分布,分析了隔热屏板型、吹风比、开孔率等参数对气膜冷却效率的影响。实验中板型选取了平板和纵向波纹隔热屏,吹风比变化范围是0.5~3.0,开孔率变化范围是1.4%~3.7%。结果表明:相比于平板隔热屏的气膜冷却效率沿程逐渐增加,纵向波纹隔热屏的气膜冷却效率随波纹板的起伏而起伏且大于平板隔热屏;随着吹风比的增加气膜冷却效率逐渐加大,在吹风比为3.0时达到最大值;气膜冷却效率在波峰处低,波谷处高,整体上随波纹板的起伏而波动,吹风比越小,气膜冷却效率随波纹板的起伏变化越明显;高吹风比(吹风比为2.0~3.0)下,气膜冷却效率沿程变化与增幅较为缓慢;整体上,随着开孔率的增加气膜冷却效率逐渐加大,小开孔率(开孔率为1.4%、2.7%)下的气膜冷却效率相差不大,但在次流背风侧,开孔率小的气膜冷却效率要小于开孔率大的气膜冷却效率。