纵向波纹隔热屏气膜冷却特性实验

针对加力燃烧室纵向波纹隔热屏气膜冷却效果开展了细致的实验研究,利用红外热像仪测量了隔热屏壁面的温度分布,分析了隔热屏板型、吹风比、开孔率等参数对气膜冷却效率的影响。实验中板型选取了平板和纵向波纹隔热屏,吹风比变化范围是0.5~3.0,开孔率变化范围是1.4%~3.7%。结果表明:相比于平板隔热屏的气膜冷却效率沿程逐渐增加,纵向波纹隔热屏的气膜冷却效率随波纹板的起伏而起伏且大于平板隔热屏;随着吹风比的增加气膜冷却效率逐渐加大,在吹风比为3.0时达到最大值;气膜冷却效率在波峰处低,波谷处高,整体上随波纹板的起伏而波动,吹风比越小,气膜冷却效率随波纹板的起伏变化越明显;高吹风比(吹风比为2.0~3.0)下,气膜冷却效率沿程变化与增幅较为缓慢;整体上,随着开孔率的增加气膜冷却效率逐渐加大,小开孔率(开孔率为1.4%、2.7%)下的气膜冷却效率相差不大,但在次流背风侧,开孔率小的气膜冷却效率要小于开孔率大的气膜冷却效率。      

一种开关磁阻电机无位置传感器控制效率优化策略

针对开关磁阻电机(SRM)的简化磁链法只能实现单相导通运行且导通区间固定的缺点,提出了一种结合固定关断角和自适应调节开通角的无位置传感器控制技术。利用曲线拟合关断位置磁链取代传统存储数据表,通过对比实时计算的动态磁链和曲线拟合的静态磁链,确定关断位置信号并估计转速和其他位置。考虑电机阻抗和电感的非线性特点,优化电感最小区域的开通角自调节模型确定导通区间。仿真结果验证了该方案的可行性和正确性,能够实现转子位置的间接检测,电机的运行效率得到进一步优化。     

针栓式推力室冷却特性试验研究

针栓式发动机具有推力调节简单、声学燃烧稳定性好和成本低廉等一系列优点,但目前对针栓式推力室的冷却特性掌握还不够深入,研制过程中曾多次出现因推力室冷却组织不好而烧蚀的问题。采用针栓式推力室试验件,对身部的冷却特性进行了深入研究,结果表明:推力室圆柱段前端的温度较低,无需采用专门的冷却措施;末端内侧气壁温度会达到约1650℃,局部存在明显的烧蚀现象,必须采取有效的热防护措施;下游冷却液膜量的变化对圆柱段的冷却特性影响较小。     

逆向进气复合角发散冷却孔流量系数试验

针对回流燃烧室外环壁面冷气与燃气流动方向相反的情况,试验研究了发散孔进气方向与环腔通道气流流动方向相反的条件下,复合角发散冷却孔流量系数随发散孔倾角(25°~55°)、偏角(90°~180°)及压降系数等参数的变化规律。研究结果表明:复合角发散孔的流量系数随倾角的增大而增大,随偏角的增大而减小；随着压降系数的增大,复合角发散孔的流量系数先呈近似线性增长,当压降系数大于0.95后,呈非线性增长且增长速度减缓。      

Applications of structural efficiency assessment method on structural-mechanical characteristics integrated design in aero-engines

In the design process of advanced aero-engines, it is necessary to carry out an effective analysis method between structural features and mechanical characteristics for a better structural optimization. Based on the structural composition and functions of aero-engines, the concept and contents of structural efficiency can reflect the relation between structural features and mechanical characteristics. In order to achieve the integrated design of structural and mechanical characteristics, one quantitative analysis method called Structural Efficiency Assessment Method (SEAM) was put forward. The structural efficiency coefficient was obtained by synthesizing the parameters to quantitatively evaluate the aero-engine structure design level. Parameterization method to evaluate structural design quality was realized. After analyzing the structural features of an actual dual-rotor system in typical high bypass ratio turbofan engines, the mechanical characteristics and structural efficiency coefficient were calculated. Structural efficiency coefficient of high-pressure rotor (0.43) is higher than that of low-pressure rotor (0.29), which directly shows the performance of the former is better, there is room for improvement in structural design of the low-pressure rotor. Thus the direction of structural optimization was pointed out. The applications of SEAM shows that the method is operational and effective in the evaluation and improvement of structural design.     

改善横向波纹隔热屏综合冷却效率的发散冷却结构优化

为改善横向波纹隔热屏综合冷却效果，采用三维数值模拟和基于支持向量机的代理优化模型，在给定的单位面积冷却空气流量下对发散冷却结构参数进行了优化研究。设计变量选取为气膜孔直径、气膜孔排布的展向间距和流向间距，以面积平均综合冷却效率作为目标函数，通过遗传算法搜索获得了设计变量区间内的优化设计点。在隔热屏单位表面积冷却空气流量G_f = 2.647 kg/（m²?s）的工况下，优化后的d、P和S分别为0.8、4和5 mm。研究结果表明，优化的隔热屏冷却结构应具有较小的气膜孔直径d和展向间距P，以及适中的流向间距S。相对于参考结构，优化后的发散冷却结构能够改善沿流向的气膜覆盖，缩减发散冷却起始段局部高温段，起到增强隔热屏发散冷却综合冷却效率的作用。     

基于MapReduce的CME参数识别模型并行计算技术

日冕物质抛射（Coronal Mass Ejection，CME）参数识别模型是太阳风预报过程的重要组成部分.在空间环境预报业务中，为提高太阳风预报的准确率，需要提高CME参数识别的精度.模型以计算任务串行的方式运行，运算效率低导致模型运算时间长，不能满足这种需求.CME参数识别模型的物理运算过程相互不独立，其在单节点上的运行方式不能满足并行化要求.基于MapReduce的并行计算框架，改进了CME参数识别模型的计算流程，提出CDMR（CME detection under MapReduce）方法，实现了CME参数识别模型的并行计算，并对比分析CME参数识别模型在串行计算和MapReduce并行计算下的运行时间，提高了模型的识别精度和计算效率.      

沸腾换热在水卡式大热流传感器研制中的应用

为了实现MW级热流环境的长时间稳态测量,研制了一种新型结构的水卡式大热流传感器。该传感器采用U型水冷通道结构,基于沸腾换热理论进行换热设计,设计量程5~15 MW/m~2。在高温超声速燃气流试验台上进行了热流测试试验,实际测试量程3~25 MW/m~2。沸腾换热理论的应用可以在较小的水流速下实现MW级热防护,大大降低了设计难度。新型结构传感器相对传统的中心冲击结构换热效率更高,可实现的量程范围更大。     

Flow mechanism between purge flow and mainstream in different turbine rim seal configurations

The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.     

新型主减隔振装置隔振性能测试试验研究

为解决新研全尺寸主减隔振装置地面性能试验中由于试验件尺寸大、重量重和试验状态多等难点,同时缩短试验周期并降低试验成本,提出了一种通过实测动载荷传递率评估主减隔振装置隔振性能的地面性能试验方法,给出了试验方案、试验夹具安装、试验内容以及过程。通过理论分析和试验结果,验证了实测动载荷传递率试验方案的可行性,测试结果真实可靠,为后续类似的系统级全尺寸隔振性能试验提供了一种新的试验方法。试验结果表明:新型主减隔振装置对垂向、航向和侧向三向激励的隔振效率均超过了80%,达到了预期的减振效果。