飞行器径向连接螺栓振动断裂分析

应用有限元分析结合试验数据，获得随机振动环境下飞行器径向连接螺栓的载荷功率谱密度（PSD）；采用基于弯曲效应的载荷与应力的线性关系，获取螺栓头根部的名义应力功率谱密度；基于Dirlik经验公式，获取应力随机过程的峰值概率密度函数和预期波峰数，联合Miner线性累积损伤模型及经应力集中系数修正的材料S-N曲线，评估径向连接螺栓头根部振动疲劳寿命，获得的结果与试验螺栓头断裂现象符合，并确定螺栓断裂原因为低频共振疲劳。     

金属微滴水平喷射关键参数调控机制及试验

均匀金属微滴喷射3D打印技术是一种极具应用前景的空间金属增材制造技术，明晰其重力敏感度是实现该技术空间化应用的前提。在地基条件下，将熔滴喷射沉积方向翻转至水平状态是直观反映其打印过程重力效应的有效方法。针对熔滴水平稳定喷射调控的难题，建立了熔滴水平喷射流体力学模型及压电激振动力学模型，通过试验，探究了熔滴水平喷射不稳定形成机制，明晰了不同喷射行为下的激振特性，揭示了熔滴水平稳定喷射调控规律。结果表明：压电模块驱动信号（脉宽、幅值）对激振杆振动特性影响极为显著，激振杆行程随幅值或脉宽的增加呈现出先增加后减小的变化规律；通过改变激振杆振动特性可调控熔滴直径、初始喷射速度及喷射稳定性，熔滴直径随幅值增大而减小，但受脉宽影响不大，而喷射速度与幅值及脉宽均正相关。基于此，试验得到了尺寸均匀的金属熔滴，并水平沉积打印出与设计模型一致的结构特征。     

燃气轮机周向拉杆转子连接刚度对转子振动特性影响的研究

为研究燃气轮机周向分布式拉杆转子轮盘间存在的连接刚度对轴系转子振动特性产生的影响，本文提出一种基于六自由度的弹簧单元等效方法；首先将轮盘接触刚度与拉杆弯曲刚度同时等效进连接界面，便于使用一维梁单元求解其临界转速与振动响应变化，验证其与全三维有限元法吻合度在3％以内；然后改写了非线性动力学方程，采用谐波平衡法对其进行求解，使用经典Newmark方法验证其准确性；最后使用该等效方法计算了某模拟转子连接刚度对其临界转速、响应特性、非线性特性等的影响。计算结果表明：当连接面剪切刚度与弯曲刚度减小3个数量级，均造成了临界转速的降低和振动响应的提高，而其影响程度可由各阶振型大致推测，且响应幅值受剪切刚度影响较大；使用临界转速趋于收敛时的连接刚度与试验值的对比误差小于2％，较连续模型提升显著；在连接刚度各向异性时，每一阶临界转速均出现两个响应峰值，轴心轨迹变成椭圆；考虑刚度随位移变化（非线性刚度）后，转子的响应峰值发生“歪扭”特性，且该峰值特征随不平衡量、无量纲阻尼等因素变化而呈现“波浪形”变化。     

椭圆振动切削加工的同步控制研究

利用椭圆振动切削加工的回转体表面微织构是在机床主轴旋转、平台进给和装置椭圆振动的联合运动下得到的,机床主轴转动与装置位移输出如果不能保持完全的实时同步,会造成微织构加工的偏差。为了解决这一问题,提出了一种新的基于转角的同步控制方法,该方法在主轴的对位基准处实现装置正弦信号的复位,以修正转速漂移造成的加工位置误差,并通过判断主轴角度信号实时输出对应幅值电压来实时同步信号输出和机床旋转运动。基于LabVIEW FPGA搭建同步控制模块,经试验验证,利用该方法加工的矩形阵列微织构轴向排列与中轴线平行,与周向排列的夹角和仿真结果的偏差不超过0.1°,织构深度随转角的不同发生预设的变化,因此,同步控制方法具有实时同步控制椭圆振动切削装置的能力。     

Semi-supervised gear fault diagnosis using raw vibration signal based on deep learning

In aerospace industry, gears are the most common parts of a mechanical transmission system. Gear pitting faults could cause the transmission system to crash and give rise to safety disaster. It is always a challenging problem to diagnose the gear pitting condition directly through the raw signal of vibration. In this paper, a novel method named augmented deep sparse autoencoder (ADSAE) is proposed. The method can be used to diagnose the gear pitting fault with relatively few raw vibration signal data. This method is mainly based on the theory of pitting fault diagnosis and creatively combines with both data augmentation ideology and the deep sparse autoencoder algorithm for the fault diagnosis of gear wear. The effectiveness of the proposed method is validated by experiments of six types of gear pitting conditions. The results show that the ADSAE method can effectively increase the network generalization ability and robustness with very high accuracy. This method can effectively diagnose different gear pitting conditions and show the obvious trend according to the severity of gear wear faults. The results obtained by the ADSAE method proposed in this paper are compared with those obtained by other common deep learning methods. This paper provides an important insight into the field of gear fault diagnosis based on deep learning and has a potential practical application value.     

航空发动机双转子系统“临界跟随”现象的机理及影响

为了探明“临界跟随”现象导致航空发动机振动居高不下的产生机理,建立了考虑中介轴承的双转子动力学模型,推导了双转子发生“临界跟随”现象时参数之间的关系,分析了“临界跟随”状态下转子系统的动力学特性。结果表明:“临界跟随”现象会导致转子系统无法越过盘偏摆振型临界转速,造成转子振动对不平衡质量分布极其敏感,其主要影响因素为盘极转动惯量与直径转动惯量的比值(简称惯量比)以及双转子增速比；当高压盘等效惯量比等于1,或增速比与任意低压盘惯量比相等时,转子系统表现出高压激励条件下的“临界跟随”特征；当低压盘惯量比等于1,或增速比与高压盘等效惯量比的乘积等于1时,转子系统表现出低压激励条件下的“临界跟随”特征。提出了必须严格控制航空发动机叶盘的等效惯量比以及双转子转速控制律的设计建议。      

比例与非比例加载下30CrMnSiA钢多轴高周疲劳失效分析

为了分析比例与非比例加载下,30CrMnSiA钢的多轴高周疲劳的失效规律。通过对30CrMnSiA钢材料开展比例与非比例(δ=90°)加载下的多轴高周疲劳试验,研究了应力幅比和相位差对疲劳寿命、断口特征及裂纹起裂角度的影响。试验结果表明,对于比例与非比例加载,随着应力幅比的增大,多轴疲劳寿命逐渐增加。对疲劳断口分析发现,裂纹萌生于试件表面,断口有明显的疲劳源区、扩展区和瞬断区,不同加载路径下的试件断口形式有明显差异。通过对起裂角度的分析发现,应力幅比大于0.25时表面裂纹有明显的第Ⅰ阶段向第Ⅱ阶段的转变,且第Ⅰ阶段沿着接近最大剪应力幅值平面方向扩展,第Ⅱ阶段沿着接近最大正应力平面方向扩展。此外,对典型试件的疲劳断口及表面扩展路径进行了分析,研究表明多轴疲劳试验试件裂纹的特征比值在0.3~0.5之间,且裂纹沿深度方向扩展至300 μm时占总寿命的85%以上。      

Investigation on nonlinear lateral-torsional coupled vibration of a rotor system with substantial unbalance

Substantial unbalance may be caused by fan blade off during the operation period of gas turbine engines, and related dynamic problems are very critical to the safety design of rotor system in aero-engine. This article aims to understand lateral-torsional coupled vibration of the rotor system with substantial unbalance. The governing equation of a modified unbalanced rotor system is established based on Lagrangian approach. Then, a mathematical analytical method is proposed in which a linear approximation is derived and the Floquet theory and Hill’s method are incorporated, from which the modal characteristics of the unbalanced rotor are obtained. The modal characteristics of the unbalanced rotor system are revealed comprehensively for the first time. Furthermore, the relation between the modes and responses of the unbalanced rotor is discussed in detail. The results show that the lateral vibration and torsional vibration of the unbalanced rotor are coupled through the inertial terms in the governing equations. Due to the coupling, veering and lock-in phenomena occur between the frequencies of the forward whirl mode and the torsional mode. Furthermore, lock-in can lead to a kind of principal instability. With regard to the response of the unbalanced rotor, both natural vibration components and enforced vibration components appear in the lateral response, while only natural vibration components appear during torsional vibration. Moreover, natural vibration components play a crucial role in the response within the principal instability region and cause divergence of the vibration amplitudes in the lateral and torsional directions.     

基于载荷当量安装误差的面齿轮振动特性

以面齿轮传动系统为研究对象,考虑载荷作用下面齿轮传动系统中支撑结构变形和轮齿弹性变形,通过将传动系统变形等效到面齿轮和直齿轮安装误差方向,建立包含当量安装误差的面齿轮多自由度耦合振动分析模型；采用4阶Runge-Kutta法求解了面齿轮传动系统运动微分方程,得到了当量安装误差对面齿轮振动加速度和法向动态啮合力的影响；开展了面齿轮动态特性测试试验,试验结果表明:偏置距误差和轴交角误差引起的面齿轮沿x方向振动加速度大于沿z方向振动加速度；偏置距误差对面齿轮x方向振动加速度的影响大于轴交角误差。      

基于磁链辨识的无轴承薄片电机轴向振动抑制策略

为了进一步提高BPMSM的悬浮性能,提出了一种基于磁链辨识的BPMSM轴向振动抑制策略,通过转子磁链的变化来估测转子轴向偏移量,然后将轴向偏移量转化为d轴电流分量参考值i*d,通过对i*d的调节来改善薄片转子的轴向恢复力,实现对轴向振动的有效抑制,从而有效改善电机的悬浮性能。试验结果表明:所提出的轴向振动抑制策略能够对薄片转子轴向振动进行有效抑制,提高系统的抗干扰能力,系统的运行性能得到了有效改善。