PMSM电流预测控制参数误差量化分析方法

交流永磁同步电机（PMSM）电流环控制性能是制约交流伺服系统性能的关键。电流预测控制拥有更快的动态响应、更低的电流谐波和优良的转矩响应，但该算法依赖精确的电机模型，参数失配会引发稳态电流误差，无法输出额定转矩，进而导致电机转矩输出效率降低。根据永磁同步电机电流预测模型，详细分析了d、q轴电流静差产生的原因，以及电流预测控制对电机参数误差的敏感性，提出了一种参数误差量化分析方法。该方法引入了电机参数偏差因子，量化描述了电机电感、磁链参数误差与电流静差之间的制约关系。通过仿真分析，验证了所提方法的合理性，为高性能永磁伺服电流预测数字控制技术打下了良好基础。     

Design of nanofluid-cooled heat sink using topology optimization

The paper presented topology optimization of 2D and 3D Nanofluid-Cooled Heat Sink (NCHS). The flow and heat transfer problem in the NCHS was treated as a single-phase nanofluid based convective heat transfer model. The temperature-dependent fluid properties were taken into account in the model due to the strong temperature-dependent features of nanofluids. An average temperature minimum problem was studied subject to the fluid area and energy dissipation constraints by using the density method. In the method, the design variable is updated according to the gradient information obtained by an adjoint based sensitivity analysis process. The effects of the energy dissipation constraint, temperature-dependent fluid properties and nanofluid characteristics on optimal configurations of NCHS were numerically investigated with following conclusions. Firstly, branched flow channels in the optimal configuration increased with the rise of the allowed energy dissipation. Secondly, temperature-dependent fluid properties were significant for obtaining the appropriate optimal results with best cooling performance. Thirdly, heat transfer performances of optimal configurations were enhanced by reducing the nanoparticle diameter or increasing the nanoparticle volume fraction. Fourthly, the optimal configuration for nanofluid had better cooling performance than that for its base fluid.     

航天器自主导航状态估计方法研究综述

自主导航是航天器自主运行的核心关键技术。状态估计是实现航天器自主导航的核心手段，是指实时确定航天器在轨位置、速度和姿态等导航参数，是航天器自主导航技术的重点发展方向之一。首先，针对航天器自主导航的实际需求，阐述了研究航天器自主导航状态估计方法的必要性，具体从导航系统可观测性分析、导航滤波算法、导航系统误差补偿3个方面介绍了航天器自主导航状态估计方法的研究现状；然后，分析并总结状态估计方法在航天器自主导航系统中的实际应用；最后，结合理论研究和实际应用，给出了状态估计方法目前存在的主要问题并对其后续发展进行了展望。     

高能合成煤油GN-1性能研究 --“液体火箭推进”专刊

结合火箭发动机工程应用环境，研究了GN-1煤油高温高压热物性、安全特性、传热结焦性能以及点火延迟性能，并和现役火箭煤油作了对比分析。采用商业仪器对GN-1煤油在最高200℃、最高压力25MPa范围内的密度、黏度、定压比热容、导热系数、表面张力进行了实验测量。在实验数据的基础上，依据基团贡献法、基于比容平移法则的P-R方程、摩擦理论、广义对应态原理分别对GN-1煤油在最高350℃、最高压力60MPa范围内的密度、黏度、定压比热容、导热系数、表面张力进行了理论计算，建立了GN-1煤油的密度方程、黏度方程、导热系数方程，并将方程的计算值与实验值进行了对比，计算偏差较小。对GN-1煤油和火箭煤油的安全性能进行对比研究，GN-1煤油的闪点为40℃，自燃温度为305℃，高于火箭煤油(225℃)；燃点为47℃，低于火箭煤油(82℃)，GN-1煤油的爆炸极限范围为0.44%-2.9%（40℃）。GN-1煤油和火箭煤油的急性经口毒性LD50＞5000mg/kg，均属于第五级化合物（实际无毒）。在入口压力10 MPa，流速10 m·s-1，内壁温480℃条件下，GN-1煤油的传热系数比火箭煤油提高14.4%，建立了传热准则方程。GN-1煤油出口油温220℃时试验段平均结焦速率是出口油温150℃时的4.43倍，GN-1煤油不锈钢材质管路中试验段平均结焦为高合管材质管路中的22.3%。在970K-1105K温度范围内，GN-1煤油的点火延迟时间为320μs-471μs，是火箭煤油的55.6%-69.3%。相关研究可对发动机可靠设计及应用提供重要参考。     

Framework and development of data-driven physics based model with application in dimensional accuracy prediction in pocket milling

In the manufacturing of thin wall components for aerospace industry, apart from the side wall contour error, the Remaining Bottom Thickness Error (RBTE) for the thin-wall pocket component (e.g. rocket shell) is of the same importance but overlooked in current research. If the RBTE reduces by 30%, the weight reduction of the entire component will reach up to tens of kilograms while improving the dynamic balance performance of the large component. Current RBTE control requires the off-process measurement of limited discrete points on the component bottom to provide the reference value for compensation. This leads to incompleteness in the remaining bottom thickness control and redundant measurement in manufacturing. In this paper, the framework of data-driven physics based model is proposed and developed for the real-time prediction of critical quality for large components, which enables accurate prediction and compensation of RBTE value for the thin wall components. The physics based model considers the primary root cause, in terms of tool deflection and clamping stiffness induced Axial Material Removal Thickness (AMRT) variation, for the RBTE formation. And to incorporate the dynamic and inherent coupling of the complicated manufacturing system, the multi-feature fusion and machine learning algorithm, i.e. kernel Principal Component Analysis (kPCA) and kernel Support Vector Regression (kSVR), are incorporated with the physics based model. Therefore, the proposed data-driven physics based model combines both process mechanism and the system disturbance to achieve better prediction accuracy. The final verification experiment is implemented to validate the effectiveness of the proposed method for dimensional accuracy prediction in pocket milling, and the prediction accuracy of AMRT achieves 0.014 mm and 0.019 mm for straight and corner milling, respectively.     

高热流密度燃烧室壁面阵列空气射流-燃油组合冷却结构研究（爆震专刊）

针对高热流密度燃烧室壁面热防护需求提出了一种空气阵列射流冲击和燃油冷却肋板的集成冷却方式,在射流平均雷诺数(Re_j)为10000至30000、燃油进口流速(v_f)为2.33m/s至5.23m/s的范围内,采用数值模拟方法对其传热特性进行了研究,并基于壁面加热侧当量对流换热系数的概念,分析了基准肋板以及燃油冷却肋板的传热增强作用。与无肋板靶面的阵列射流冲击相比,带肋板阵列射流冲击的面积平均当量对流换热系数是前者的1.6倍,压力损失系数相对提高了约25%；采用燃油冷却肋板,加热壁面综合传热能力进一步增强,在Re_j=10000时,采用燃油冷却肋板的面积平均当量对流换热系数是基准肋板的1.5倍以上,即使在Re_j=30000时,燃油冷却肋板的传热增强比也可以达到1.2；燃油冷却肋板的出口温度相对进口温度的提升在20K~50K范围内,其提升幅度随着射流雷诺数或燃油进口流速的增大而减小。     

Modeling and experiment of grinding wheel axial profiles based on gear hobs

Hobbing is one of the crucial gear manufacturing processes with high precision and high efficiency. In order to improve the accuracy of hobbing and hob relief grinding, more precise grinding wheels are demanded for relief grinding in the production of gear hobs. In this paper, a new and accurate mathematical method for calculating the axial profile of grinding wheel based on the corresponding gear hob to be ground is proposed. Considering that most researches have been conducted to focus on the optimization of hob geometric feature and only can be applied to a specific type of hand of helix and rake angle of gear hobs. The method in this paper can be served as a general algorithm for generating axial profile of grinding wheels on the basis of the spatial envelope theory, the principle of coordinate system transformation, and studies on normal profile of single-tooth. The accuracy of grinding hobs is based on applying the approach in practical manufacturing. Taking two typical different kinds of pre-grinding gear hobs as examples for calculation and experiment, the results of tooth profile errors strengthen the position that the validity and feasibility of this method, it can be employed for gear hob design and grinding processing.     

散射对高温气体-碳黑颗粒混合物辐射传输的影响

基于全光谱k分布(Full spectrum k distribution,FSK)模型、MIE理论和有限体积法(Finite volume method,FVM),构建了均温、均质辐射参与性气体-碳黑颗粒混合物介质热辐射传输模型,并分析了碳黑不同尺寸、不同体积浓度以及介质不同路径长度和不同温度条件下,因忽略碳黑颗粒散射所导致的介质热辐射传输特性(如辐射热流、辐射源项)的计算误差。研究结果表明:体积分数不变,增大粒径,计算误差呈现出先增大后减小的趋势;数密度不变,增大粒径,或者粒径不变,增大体积分数,均将使得计算误差相应增大;粒径、体积分数不变,增大路径长度,或者升高介质温度,均将增大计算误差。通常对于含有大颗粒、高碳黑浓度的辐射参与性气体-碳黑颗粒混合物介质,碳黑颗粒散射不能忽略。     

Experimental and numerical investigation on surface quality for two-point incremental sheet forming with interpolator

The unsatisfied surface quality seriously impedes the wide application of incremental sheet forming (ISF) in industrial field. As a novel approach, the interpolator method is a promising strategy to enhance the surface quality in ISF. However, the mechanism for the improvement of surface quality and the influence of interpolator properties on surface roughness are not well understood. In this paper, the influences of process variables (i.e. tool diameter, step size and thickness of interpolators) on the forming process (e.g. surface roughness, forming force and geometric error) are investigated through a systematic experimental approach of central composite design (CCD) in two-point incremental sheet forming (TPIF). It is obtained that the increase in thickness of interpolators decreases the surface roughness in direction vertical to the tool path while increases the surface roughness in direction horizontal to the tool path. Nevertheless, the combined influence between thickness of interpolators and process parameters (tool diameter and step size) is limited. Meanwhile, the placement of interpolator has little influence on the effective forming force of blank. In addition, the geometric error enlarges with the increase of step size and thickness of interpolator while decreases firstly and then increase with an increase in tool diameter. Finally, the influencing mechanism of the interpolator method on surface quality can be attributed to the decrease of the contact pressure due to the increase of contact area with the unchanged contact force. Meanwhile, the interpolator method eliminates the sliding friction on the surface of blank due to the stable relative position between the blank and the interpolator.     

基于视频的行人再识别

行人再识别是指在无交叉区域的多摄像机视频监控系统中,匹配不同摄像机中的相同行人目标。本文提出了一种基于视频的行人再识别方法,用HOG3D来描述一组视频的时空特征,在训练集上用预训练的DenseNet来微调模型参数,利用迁移学习得到的模型来提取视频中行人的表观特征,融合两种特征来描述视频序列中的行人。最后将融合的高维特征降维,并用度量学习方法计算行人对之间的距离。本文在PRID 2011和iLIDS-VID这两个视频数据集上进行了使用,实验结果表明本文的方法取得了较高的累积匹配得分。